Salut, încă nu am pus-o pe dyno pentru că după 300 km a crăpat cutia, am făcut swap la DSG și sunt aproape gata și o să fac după, oricum undeva la 350 aproximativ.
@georgiK_5 күн бұрын
@@WRCgarage wow 350=)), cat a costat, si cam ce consum are acu =)
@WRCgarage5 күн бұрын
@georgiK_ Am toata lista la descriere la ultimul clip si pretul total, nu stiu ce consum are.
@landrovervideos11827 күн бұрын
Just bought this kit after breaking a tap in the timing chain guide excellent tool
@cipriangrad69887 күн бұрын
Mulțumesc ❤
@Anonim-fy2mx11 күн бұрын
Am înlocuit și eu axul cu came cuzineți și tacheti . Dar după motorul nu mai trage ca înainte Înainte trăgea de Numa, acum numai are lag mare Sa fi greșit ceva?
@WRCgarage11 күн бұрын
Daca ai pus axa corect înseamnă ca ai pus avansul la distribuție diferit si de asta nu mai trage asa. Pune un tester si vezi daca e pe zero sau -1.5 daca e edc16
@Anonim-fy2mx10 күн бұрын
@@WRCgarage ecd16 ce înseamnă? Nu ma pricep. Mecanicul a zis ca a pus avansul pe 0 Dar am lag foarte mare
@WRCgarage7 күн бұрын
Tipul de calculator (ecu) depinde de mașină daca e mai veche sau mai noua
@Anonim-fy2mx6 күн бұрын
@@WRCgarage Ok Mașina e din 2002 Mecanicul nu folosește vcds are altfel de tester. Și mia zis ca unghiul de torsiune la pus la 0 , dar nu trage ca înainte și turbina nu mai intra asa repede Am verificat furtune vacum toate sunt Ok Poate fi pompa tandem defecta dar e noua nouță
@Anonim-fy2mx6 күн бұрын
@@WRCgarage ce valoare trebuie sa aibe motorul 1,9 ajm?
@John-hv5sx12 күн бұрын
In the manual it says to measure 15mm from the bottom of the cylimder do u think it makes a difference from measuring from top
@WRCgarage12 күн бұрын
Yes, it does, you have to measure it 15-20 mm from the top or bottom of the cylinder to have a precise measurement.
@simonkrezias761512 күн бұрын
Great video.Rebuilding as it should be! Is there another with a Common rail tdi with two cams?
@WRCgarage12 күн бұрын
Thank you, yes it is the 16v ones
@simonkrezias761512 күн бұрын
@@WRCgarage Thanks for your answer but have you put it up on YT,I cannot find it.
@WRCgarage12 күн бұрын
Unfortunately i don't have any video with 16v yet
@miketaylor628213 күн бұрын
It was time for the first oil change by the time the engine started, oh and a new starter. 😂
@WRCgarage13 күн бұрын
Not everyone understands that i did that on purpose to lubricate all the parts with oil before starting, but it's okay. I'll let all the smarties comment as long as i know what I'm doing i'm not bothered.
@andreiiurciuc190113 күн бұрын
Sunteti prin România faceti reparatii ?
@WRCgarage13 күн бұрын
Sunt in tara dar nu repar cutii de viteze
@andreiiurciuc190113 күн бұрын
@@WRCgarage pe motor. Daca este cazul am tot asz
@WRCgarage5 күн бұрын
Doar recondiționare totală la motor
@andreiiurciuc190113 күн бұрын
Mulțumesc pentru video
@Justiceandlaw13 күн бұрын
Clean, perfect,accurate and quality job...
@traianraduastelean801614 күн бұрын
Salut Care e diferența de a monta injectorul chiar in admisie cum l-ai pis tu sau mai in spate pe traseu? Nu e periculos pt motor (fiabilitate) sa fie chiar in admisie? Si cam de la ce boost ai recomanda inceperea injecție tinad cont ca full boost e la 2.5 bar Mulțumesc
@WRCgarage14 күн бұрын
Salut, nu prea e mare diferență, ideea era să fie cât mai aproape de admisie ca să ajungă cât mai repede injecția de methanol.
@secretvenda857415 күн бұрын
My dumbass think i can do this 😂
@papascabs276716 күн бұрын
Ahhhh! That sounds absolutely delightful when it starts!
@papascabs276716 күн бұрын
How do you like the clutch? It looks like a racing style?
@WRCgarage16 күн бұрын
The clutch isn't the best option for comfort, but it is a Sachs SRE performance ceramic paddle with dual mass. It holds a lot of power, but it is very, very annoying in town as it takes a bit of force to push it down.
@michaelakerman786017 күн бұрын
Amazing! Should there be a pipe from the PCV valve on the crankcase?
@WRCgarage17 күн бұрын
Yes, but it's going to a catch can, then under the car
@michaelakerman786017 күн бұрын
@WRCgarage is there a way on these engines to test the pcv valve is working correctly? I have a 1.9tdi transporter, blue smoke from exhaust, leak and pressure test all good. Thinking might be the pcv valve stuck open/closed
@WRCgarage5 күн бұрын
I don't know if there is any test for them, but you can check if your oil stick jumps out or if you have excessive pressure when you open the oil cap.
@IsaacKofiArthur-od6bb18 күн бұрын
great video!!!
@059898056821 күн бұрын
We never put the ring gap in the thrust side of the piston top ring needs to be 180 degrees from the second ring.
@WRCgarage5 күн бұрын
I don't really get what you meant, but I always install them like that, 180°, and I've never had a problem. I always get good compression.
@05989805684 күн бұрын
@@WRCgarage we always put ring gap on the wrist pin sides. When we replaced pistons on 2.5 liter ecotechs (oil consumption issues) we would find ring gaps that we aligned with each other. We always wondered if they were installed that way or if the moved while the engine was running.
@vasilistheodoropoulos995923 күн бұрын
Do you have Instagram or fb? I want to ask you something for my car 1.9 tdi
@WRCgarage22 күн бұрын
Ask me here, if i can i will answer it
@antn838727 күн бұрын
wow a cast iron block with piston cooling jets!!!
@discoverinnerpeace457427 күн бұрын
Sincer mi a fost de folos video tău am un b5.5 1.8t și l am schimbat acum cam 15 minute toate treaba , 😂 am crezut ca trebuie sa dau bară față jos și etc , mersi mult !
@nicolaenita5127 күн бұрын
👌
@discoverinnerpeace457427 күн бұрын
Salut păi și dacă am aerul pornit și el nu merge de nici un fel , nu prea bagă rece de la el să fie nu ?
@WRCgarage25 күн бұрын
Foarte posibil !
@mikoaipan735129 күн бұрын
⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛⬛
@roscaandreea5681Ай бұрын
Cum procedezi daca s-a rupt surubul de la axa cu came cel de 18 ?
@WRCgarageАй бұрын
Salut, nu am pățit asta până acum, dar dacă mai este ceva rămas la exterior, puteți încerca să sudați o piuliță în cap sau, dacă nu, găuriți cu burghiul de la cel mai mic până se ajunge la diametrul șurubului.
@arnabbiswas3973Ай бұрын
call bmw dtsi 2}2
@WRCgarage25 күн бұрын
Call baby !
@ionion6318Ай бұрын
Da dar are un mic semn pe pistol
@WRCgarage25 күн бұрын
La scutere, asta e motor de masina !
@mihaihans287Ай бұрын
vrajala multa cu masurarea si alinierea injectoarelor.cind ii pui blocatorul cu surubul vine perfect la punct dar pe youtube e la moda vrajala multa
@WRCgarageАй бұрын
Asa este, e vrăjeală mare rău, aveti grija sa nu faceți asa...
@mariusmazutis9844Ай бұрын
Hey, is it the same for Passat b6 2.0 tdi BMR?
@WRCgarage25 күн бұрын
Yes !
@v0tke245Ай бұрын
Hi what the point to lubricate head gasket?
@WRCgarage25 күн бұрын
Read the comments!
@have-a-gorepairhero2760Ай бұрын
What tool did you use to get to the difficuly bolt at the back? I've heard a union joint but what size? That's 😊
@WRCgarage25 күн бұрын
Just a 10 mm or a Torx, depending on what type you've got there.
@konstantinsherbetov2865Ай бұрын
Nice video, but loose the stupid music :)
@WRCgarageАй бұрын
Sorry, mate. KZbin asked me to change the music for copyright reasons.
@konstantinsherbetov2865Ай бұрын
@@WRCgarage just don't put any, it is going to be better!
@WRCgarageАй бұрын
@konstantinsherbetov2865 It was too late for that, as the only option was to choose a KZbin-approved one.
@AndreiB62.0TDIАй бұрын
merge pusa axa de sdi pe 2.0 bmp cu o axa cu came ?
@WRCgarage25 күн бұрын
Cred că da, nu am pus, dar am înțeles că au pus alții și merge.
@heizerbirne5892Ай бұрын
old camshaftbearings :(
@WRCgarageАй бұрын
If you don't follow my channel, why do you comment without at least reading the comments? The bearings are new, just 860 km with the same camshaft. I just took the camshaft off because it's been an issue with the edge of the lifters. Then I put everything back. When you spend 8k on one engine, believe me, it's not about the money. There's just no need for new ones, as they're new and not even break in.
@heizerbirne5892Ай бұрын
@@WRCgarage Because the camshaftbearings (not crankshaftbearings) look really bad
@WRCgarageАй бұрын
Any new camshaft bearings after just one mile from new will look like that. They have a layer on them for breaking in, but that doesn't mean they are old.
@user-jp9hm2is8vАй бұрын
Ax cu came ce firma ai folosit sau care este mai bun multumesc.
@WRCgarageАй бұрын
Kolbenschmidt.
@user-jp9hm2is8vАй бұрын
@@WRCgarage multumesc
@user-jp9hm2is8vАй бұрын
Va mai rog ceva tot aceleași proceduri de strangere și montare sunt și la 2,0 tdi 140 ps?
@WRCgarageАй бұрын
@user-jp9hm2is8v La 16v nu stiu exact, trebuie sa verificați într-o carte specificatiile.
@dumitrupaun6098Ай бұрын
Noroc!cat ajunge manopera la lucrarea asta? mulțumesc!
@WRCgarage25 күн бұрын
Salut, momentan lucrez doar pe masinile personale dar cred ca undeva la 300-400 lei
@YuriyFITSAKАй бұрын
Loji.zrizowskii.lashara.m550
@siliconeheaters1492Ай бұрын
Te-am urmarit cu mare placere, cu cafeaua langa mine. Treaba faina, te unge la suflet!
@WRCgarageАй бұрын
Mulțumesc frumos !
@HURRlCANEVIEWSАй бұрын
I just need to install the camshaft gear, is there a way to install it without the tool?
@WRCgarageАй бұрын
No, you can't install it wrong. Just make sure the toothed wheel has the toothed gap facing the top as you see in video.
@dp8685Ай бұрын
Why smear oil on head gasket?
@WRCgarageАй бұрын
I answered to another 50 with the same question, it would help me if everyone check the comments before, the oil is not necessary but i just do it because i fell that in that way will seal better but again its not necessary.
@1vantheterr1ble47Ай бұрын
I see a lot of very precise measuring - for what? They sent you the wrong parts?
@WRCgarageАй бұрын
This is a must when you rebuild an engine, no wrong parts
@ViiralDznАй бұрын
miss my 1.9 tdi pd, solid motor never ever gave me problems lol
@danielrus10822 ай бұрын
Cum se face reglarea injectoarelor ?????????????
@WRCgarage2 ай бұрын
Daca te uiți pe canal aflii imediat, ai totul pe tavă ...
@Marian2122222 ай бұрын
Distributia este la fel ca si la golf 4 1.9 ajm?
@WRCgarage2 ай бұрын
Salut, da dar la ajm mai ai inca un intinzator hidraulic, dar cu punerea la punct este identic !