Fixed my issue in 15 minutes. Thank you 👍

Hello, could you please provide the trigger measurements?

Pull your blocks

I’m having this problem even with a drop in after this happened

thanks bro, that fxed my issue

Good job 👍 nice truck

Great video thank you

If you run a 35x11.50 on factory 18 wheels or 285/75r18 (34.8x11) they will fit just fine. No wheel spacers needed.

I have a problem to were it will shoot once then the trigger won't reset just stay stuck in place even with the upper off should I just get a new trigger?

Thank you. My kit was t together correcty but it isn't ihtting the disconnector at all. I haven't shot it because I knew it was going to possibly shoot on its own. I was staring at it and playing with it and realized it was not matching like it should. Out od spec. So thank you. This is exactly what is wrong. You saved me a lot of hit and miss.

You are a good man, sir. Because you care.

Free machine gun weeeeeeee. In all seriousness, I left the sear spring out of my first AR on accident, free machine gun, but unpredictable af.

Binary is legal.

This happened on my RA 434 drop in

My build has a crappy trigger pull and gets hung up on the reset I go to pull the trigger and it’s like the safe is on remove pressure and go right back on works fine 15 20 cycles then hemmes up again. I am petrified to f with the trigger but might investigate it a bit and see if it will clean up…. Awesome Vid.

O and instead of going thru all of this you can but a nice stainless Anderson firing group for 19 bucks and they are silky smooth

I know this is 6yrs old but bianary trigger are legal now lol

Yg pas nya gini aja untuk mobil uty ini bos hahahaha....

Dude, huge thanks

I have a problem with the trigger not setting after I queeze it. I fails the function test. Now I know the problem. I just don't have the tools to fix it. I know a good smith to take it to. Good to know others have problems too.

Great video! I just finished an AR15 pistol and it dbbl fired! Never happened before and I wasn’t sure it even did until I saw two shells! My bad -first by putting disconnected spring upside down 🤦🏻‍♂️… I fixed that but now I have a very slight 1/8” pull before trigger actually engages. My best description would be what it feels like when safety is on and you attempt to fire getting that little pull before safety stops you. Any idea what’s happening?

absolutely legal....its called binary trigger....identifies as TRY\ME.

1) binary triggers are not illegal. 2) that Dremel should not be anywhere near your trigger. 3) if you have a problem get a new disconnector or check that your spring is installed correctly. Do not dremel or file triggers 4) If you want a lighter trigger get a nice two-stage component trigger like the larue mbt2s or Schmidt tool

Thank's for the video I'm'm thinking of getting spintech exhaust for my foxbody, can you give more details on your setup? Did you have catalytic converters X or H pipe and was this 333SCS or 333DSC?

Polymer 80 lower.. double fire city.. going to fix that ASAP..tried a new hammer.. same shit.. disconnecter..never thought of that gap..ty..be safe

Thank you I am having this issue with a brand new 9mm rifle. I did swap out the springs for the JP3.5 springs which I have on three other ars and have not had this issue. Could those springs have anything to do with this issue.

🔥Sick vid👍

Dremels and triggers are a bad combination.

Binary is legal unless it’s not legal in your state!

Your the goat 🐐 for this one

58 seconds GET TO THE FUCKING POINT or just shut the fuck up and forget the video Cause your stupid. There is 1mil vids like this where the person should just forget it Know what you’re gunna say before you start the vid! Or just forget it Cause you’re stupid

Thanks! Worked like a charm.

Binary triggers are not illegal. ATF has not went against them. It's not a force resetting binary trigger like the WOT. Some states binary triggers are illegal tho

Hi man I have the same truck, but did you put wheel spacers? I bought a leveled kit from rough country and 35’s, I don’t install yet. I want to know if you installed a wheel spacers.

So everyone is going to just ignore Mr. Potato Head

Thank u for the Info very helpful

Awesome, thanks for the info. .50 beowulf double fire scared the crap out of me. Easy fix

IDK people pay good money for binary triggers. Free built in binary trigger sounds like a bargain.

Está bien linda la camioneta

Are most forged uppers all equal to eachother? Does BCM actually make a better upper than a psa?

In theory, if you removed the disconnector, would it be full auto?

So to sum it up, you messed with a mil-spec trigger, designed not to be a 3 lb. target trigger but designed for combat, and in changing four precision metal surfaces with your Dremel tool, you screwed it up and NOW have fixed the problems you created. Is that about right?

I’ve had a lot of stuck cases reloading brass and steel alike their actually very similar and I usually just remover to top thingy and hammer em with the rod or a old hinge pin or something.

Depends on where you are but binary is legal in some states and full auto is still legal if you have an 07 ffl and an 02 sot

Short story is be very careful with trigger mods.

Disconnector not extractor

Looks real good 👍

Thank you so much! I appreciate this video!

Realize too that parts here are often surface hardened. Once you kiss them with that grinding stone, you remove the hard facing and then the parts will wear quickly due to the softer steel being exposed.

Would be better if you used proper terms for the parts. Its a disconnector vice an extractor. geez. Glad you corrected that later in.