Thanks for the video! This same approach (buying the replacement switch) and swapping out the two parts worked for my 2005 Acura TSX. For my repair, I removed the airbag (kzbin.info/www/bejne/gInXkGmBnLqWbK8). It doesn't seem to be possible to disconnect the plugs at the circuit board. Fortunately my switch assembly (the group of three buttons, circuit board, rubbery membrane, and housing) was just held together with the three screws. There was no need to pry on tabs to get it to come part.
@MariaLeon-yg5rx10 күн бұрын
The screws are fairly rusty on mines, are there replacements for them anywhere?
@JosephDungee11 күн бұрын
NO, you cannot fit your hand int between the Power Steering pump to grip that damn clamp...I tried at least ten time snd my friend with smaller hand than my could not grasp / pinch it. I had to remove the front lens and work the whole unit out and then put the unit back in after replacing the bulb and reclamp an dglue the lens back on.
@adamsojka608012 күн бұрын
Very useful. Thanks
@benpatton6484Ай бұрын
Why skip the actual removal of the pulley?
@onjofilmsАй бұрын
Some videos show you how to do it so you can do it, and some show you how much of a pia job is and that you don't want to do it. This is one of those videos.
@clintathusazАй бұрын
🤣
@tedjohnson64Ай бұрын
Nice video! The video is a year old…does the trunk latch still work?
@clintathusaz21 күн бұрын
It does! Not a problem at all with it!
@petermeleg8826Ай бұрын
Got to change out my clutch assy. The coil has no continuity, hence the AC comp clutch does not engage. Brilliant down to earth video. Keep up the good work. From an aged 71 year old petrolhead. No one is so clever that they can’t learn from someone else. TTFN from Ontario Canada.
@petermeleg8826Ай бұрын
Down to earth and basic. Good video mate. Just what I needed to know.
@maverickperson5443Ай бұрын
Followed the whole process and installed the pump, but now it is not engaging and steering is extremely hard to turn, what could it be? Thanks for the great video.
@xtor13Ай бұрын
Some Pump if have too many scratches will never works again ..like mine too gone after changed seal. Why mechanic sometimes say " if it's works leave it"
@upthechallangeАй бұрын
Great demonstration. I'm gonna have to try that.
@HRradnessАй бұрын
This worked great for me on a Mk7 sportwagen thanks for saving me $280
@rickjeffjeffАй бұрын
Awesome.... Easy fix... Your car will go 200000 more
@dawinksta2 ай бұрын
That’s the tensioner not the idler!!!
@meanbillydeane2 ай бұрын
Would the Mouser part work on a 2005 Acura TSX? Steering wheel button placement looks very similar on the accord in the video.
@jrrojas90502 ай бұрын
Hi, I followed this instructions to rebuild a leaking on my 2007 crv. But after putting everything back and reinstalling it, pump dond work.😢. Can't figure out what i did wrong.
@hikgerguy12342 ай бұрын
Nice vid. i think the cracks I recently noticed in my air intake tube are from be "brute forcing" the air filter cover off. Replacing the air intake tube and air filter today.
@fidelgomez91582 ай бұрын
Excellent explanation! I was having a lot of trouble lifting the air filter housing. It was so difficult! But with your fantastic explanation this will be a piece of cake. Thanks for taking the time to make life much easier for the rest of us.
@clintathusaz2 ай бұрын
Thanks you for the comment!!
@jrrojas90502 ай бұрын
did use all 6 bottles of fluid, is 3 enough if you are not draining the lines? thanks
@jrrojas90502 ай бұрын
nice!! thanks'
@yahwehkingdomministry2 ай бұрын
Dear Clint, Can you please give me the right link for the switch for 2011 honda crv lx 4door front wheel drive? Thanks YKM
@L-ot5fs2 ай бұрын
Great video
@natedeppermann71422 ай бұрын
Big thanks! Worked to fix my 2008 CRV, though I had to remove the two screws holding the center air bag unit as well. Thanks for taking the time
@Daddys_moneey2 ай бұрын
This helped a lot thank you
@gixxerboyroyluvdrumswaters90232 ай бұрын
I have the same issue, BMW need to do something about it. cant even charge my phone.
@robfrydryck1273 ай бұрын
Nice video. Clamps cheaper at Harbor Fright.
@RoosterTailFilms3 ай бұрын
anyone know if this will fit a 2016 gti?
@clintathusaz3 ай бұрын
It should.
@whans93 ай бұрын
I made a 3D printed step so it can’t fall through
@Stinkyjo553 ай бұрын
I did this, but the rear latch will not unlock and I have to manually pull the white actuator. Is there a rod that connects to the rear latch?
@fallrising54433 ай бұрын
Hey what's that retainer ring part number..? 😅😅
@goshenable3 ай бұрын
How can I make it to where when I right click and choose transparency, it makes the whole model transparent and not just one particular face? I used to be able to do this pre 2021 version.
@clintathusaz3 ай бұрын
I think in a model it will make the selected face transparent, but in an assembly, it will make the selected part transparent. Probably still not all that helpful to you though
@goshenable3 ай бұрын
@@clintathusaz That does help, I believe that may be my issue. Thanks!
@lneomty74443 ай бұрын
What is the name of the yellow tool you use for the rings?
@clintathusaz3 ай бұрын
Snap ring pliers
@stevenkerwin40413 ай бұрын
How many compressors have been replaced when this was all that was needed? Thanks for the demonstration with minimal, no-fancy tools. Great to watch the mechanics with all their pullers, etc., but no fun buying/storing rarely used tools.
@clintathusaz3 ай бұрын
Thanks! Appreciate the comment
@Emma-hg1vi3 ай бұрын
Thank you sooo much
@frankyavocados57944 ай бұрын
Can you do it without removing the heat shield?
@richardchirichillo50614 ай бұрын
Your post helped the most, thanks!
@clintathusaz3 ай бұрын
Glad to hear it!
@dazergurl4 ай бұрын
Can you remove the screws all of the way? My screws are stripped from a mechanic using the drill driver. You can use an 8mm but I'd rather use a screwdriver in the future
@itssalmonthatfly74654 ай бұрын
Thank you very much
@clintathusaz3 ай бұрын
You are welcome
@johngallagher6074 ай бұрын
How to change a high beam light?
@dantecardova48974 ай бұрын
Anyone know how to do this for 2 door ?
@bronniesboy4 ай бұрын
What was the condition of the Mount when you changed it
@mrau92me4 ай бұрын
Great video! My 2007 Accord EX-L switch assembly looks the same from the outside, but mine has two very small white connectors that I can't seem to pull off (there's no apparent tang to press to release them), even with a small pry tool. I was afraid I was going to break them, so I decided to remove the 3 screws with the electrical harness still connected. After doing so, the plastic plate on mine just came right off without having to release any clips like in this video. If your is like mine and you do it this way, be careful not to lose these 2 tiny plastic button contacts that I almost lost into my car's crevices. I hope there were only 2. I'll know for sure once I reassemble it with the switch I'm about to order using the Mouser link provided in the description above.
@rosachavez63943 күн бұрын
Are all the switches the same for all Hondas? I have a 2007 Honda accord sport.
@clintathusaz2 күн бұрын
I think it will probably work for that year accord. I assume the button panel looks the same? 2003-2007 were all the same body style
@mrau92meКүн бұрын
@@rosachavez6394the fix in this video worked for my 2007. If your switch looks like the one in this video, this fix will likely work for yours too. If yours is not working anyway, go ahead & take it apart & look to see. You can still drive the car while you're waiting for the new button to come in. Even if you go ahead and order one upfront, u won't be out that much $$ if yours is different for some odd reason
@rosachavez6394Күн бұрын
Ok perfect. Yes look a lot like it. I will have to fix mine. Thanks a lot
@CalebCx964 ай бұрын
Thanks for doing the job twice to record this! 8 year old vid that’s still helping out
@danialirsyad74384 ай бұрын
Rear sensor or front sensor?
@toddalehman5 ай бұрын
Just did this tonight - thanks so much for the handy steps and even giving a link to buy the switch. I did that but in my 2005 Accord Hybrid I couldn’t get the switch cluster out. Turned out to be necessary to remove the airbag. That’s pretty simple but I used another video (searched how to remove airbag from 2005 Honda Accord - straightforward) to walk me through those steps. The tips I’d offer: remove the airbag - makes working with the cruise cluster possible. Keep the cluster connected by wires. Once it’s loose from the steering wheel remove the 3 tiny screws as shown here then take the switch apart and replace as shown. A tip for removing the airbag: definitely use a cordless drill to remove/re-apply the screws that hold the airbag in place. Can’t wait to drive with cruise control again! Thank you for making it possible. 😊
@davidgonzales58785 ай бұрын
Would it fit a 2012 golf TDI?
@JoseRivera-uv2yk5 ай бұрын
Thank you for letting us know the precautions. A lot of folks don’t mention those things.
@ava00035 ай бұрын
Used this video today to fix my cruise control switch. Got the switch from mouser. I watched this a few years ago and never fixed it, then decided to do it a couple weeks ago. Got it in the mail and did it today. Thanks for the video and the help.
@clintathusaz3 ай бұрын
Great to hear!
@markwhaling73155 ай бұрын
Slight modification in my case. My 2007 Accord Coup cruise control assembly wires were soldered in place and could not be removed. So, I had to remove the steering wheel airbag to gain enough access to disassemble the cruise control assembly and replace the switch. Great video on airbag removal here: kzbin.info/www/bejne/Z2aUl4OMoNpoj7s&pp=ygUlMjAwNyBob25kYSBhY2NvcmQgYWlyYmFnIHJlcGxhY2VtZW50IA%3D%3D