What a difference 7 years makes, because my axle it square tubing, not a C channel.

What material?

wdym not done yet that looks clean for a 250 it looks big or maybe im just a 5'8 filipino and that looks big for me but dude that is looking dope

Solid. Ultra clear, wonderful explanation.

Nice built

Plastic Crushed Universal Pellet extruder for 3D Printer Filament Plastic Granules Crusher extruder Assembly kit install on Anet A8 or leap frog HS or even a Tenlog pro

Awesome...I'm about to build my own too!!

Did u rejet for the pod filter?

There are vAdvantages and Disadvantages to the open Axle frames Boxed Frames can hold water and Mud inside and Rust out faster, either way ?iMO all Trailers Axles have some weakness to them as far as Construction goes a plus to that is the prices of many replacement Axles has dropped significantly over the last 25 or 30 years so purchasing a upgraded one for any project is Affordable and easy to find with upgraded Spindles or whatever you want many of them can be shipped right to your door for a very reasonable cost

How is the lathe now?

Do you have the specific part numbers for the rexnord bearings?

Very nice facility, love the tools. Thank you for sharing your video.

Incredible. Thank You.

Que diámetro tiene el caño de PVC.?

You should have had the circumference marks layed out where you will cut the flat ends off and kept running through until they lined up. That may have been a backup bar for a full pen pipe and that not being spot on could have been a big prob.

Thank you for this video. I'm sitting here with almost the same pile of bearings, pulleys, arbors, etc. I wasn't certain that 1/2" diameter parts would work on a decent sized lathe. You gave me the inspiration to give it a shot. Thanks again!

What a cool project! Thanks!

Where can I purchase a Ray Peña original???? Lots of counterfeits out there!!!!! Please let me know!

Sorry you got your finger greased

Did you make a Whell Disk out of wood ?

Question, once you build this, is it easy to take apart for storage in an apartment? I’m looking for something I can store in an apartment but take to the lake or river.

Where did you get the spindle from?

Hello sir where can I get this type of spindle

I've been waiting to get one but I didn't know you have to go get a title for it...... new jersey is a pain. How do I go about that if buying from harbor freight?

I hope you don't end up with an "exwife plaintiff" as a result of all these purchases :) Thanks for sharing the information so others don't have to.

as you said, pricey piece of kit

Awesome build.love how you moved battery and cleaned up everything under the seat👍🏻.

I need two wheels that can use tires for a car, About 245/50/18's. But I need to mount hub motors in them. I'm making a three wheeler with two wheels in the front and one in the back. It will be front wheel drive.

The best tool in the whole world. I have many of them. Well made and accurate. You will never go back to anything else.

the instructions are like 80% clear and 20% “figure it out bro”

I am a Machinist and I loved this video, I have just inherited my grandfathers lathe which is overhead belt driven so this was cool to see. However one point I would like to mention is that when he said the lathes were 4 speeds, I don't think that is technically true. Most lathes from that era were back geared, which means a lathe that appears to be 4 speed is actually 8 speed.

Nice. I would love to have the plans if they are available.

I am building one soon. 16 ft on 24" diameter pvc or cpvc with 2 45 elbows at the front capped.

What size tubing did you use for the tongue??

TY sir for this video. I will make this as we have many Rainer cherry's (finally) after almost a decade. ☝we are excited to start havesting them here in WA 🌲🏔 Yippee 🤸‍♀️❣

В работе станочная мастерская не потребляет не одного келовата и не одного ватта электричества а освищение наверное на керосиновых лампах

Cannot see what you do ,too far away

Great video. Short and to the point! 👍

Обрезать бутылку и горлышком насадить на палку. Зачем столько возни.😅

#Ray MAKES /Ray MAKES @Ray MAKES where are ya? You haven’t made a new video in 6 years, how is life what’s going on man you’re a fuckin genius with your crafts.

Not enough detail

Good job on the live center.

Why didnt you fold it , if it is a folding trailer like in the photo? and What is your forever trailer if this isnt good enough ?

How did you fold it???

hello

Did you put this extruder on some printer? Any news?

Wow, great job, i want to do this on a smaller scale to make a rc boat, unmaned, for fishing, trolling, as i sit on shore and control it.

how many miles an hour is that rated for? great Job

@RayMAKES asshol*! you never reply my comment!

Pretty decent video overall if you ignore all the crying over stupid/little issues, most caused by yourself. Also, don't put pins in tongue and you can fold it down when you flipped trailer over, and wouldn't have issue with beam above you.