I just bought the 7100 crankset, it says to use the bb72 but will bb92 work aswell as its €6 difference at the moment and presumably smoother with an extra seal 🤔

Great instructions! Very thorough!

This is ingenious.

You made this easy to understand, can't thank you enough. Not to mention also how easy going you made this. Something's at times can be so unforgiving. These steps are very simple to understand. I can learn from you. Thank you..

Awesome Videos! Liked and Subbed even after all this time 😊 Thanks for taking the time to film and show us all how to. Cheers

Really informative video, many thanks

Thanks for clearly showing how the tabs are supposed to align when mounting the derailleur! Seems like every other video just totally skips over that part.

Can I install this one at Cervelo bbright 46x79? Thanks

Can I install this one at Cervelo bright 46x79mm?

Thanks

Again, many thanks for your thoughtful and methodical instructions. I have done this many times but one always learns some minor tips and tricks, you have provided a few, so again, thanks!

Thank you. Best explanation I've seen to adjust this derailleur.

Great video! Many thanks.

Top man

The cheap side of cycling is what makes it so good. Servicing your own bike, finding great deals. Thanks for your excellent videos

This is my last hope, if the tick sound still in there I might consider replacing my chain before considering to change the BB.

Amazing

Perfect vid. Now I just need one for the front

Great work

Really helpful. Thank you 👍🏻

This was such a thorough explanation. My fresh drive train went on without any issues at all, thank you.

thank you tutorial misteri

Great!

This tool should come with a WARNING, it damaged my new carbon wheels, Tyreglider offered no help at all, very poor customer service from Kevin

Thank you for the excellent explanations. However, I have a question following a problem: I have a shimano 105 FD-R7000 front derailleur, like the one in the video. It's parallel, at the right height, the limits are adjusted, but the chain touches the ends both on the big gear and on the smaller gear. I took it to the repairer, and received it back from the repairer in the same conditions, saying that it was in order. But it's still touching, is that normal?

Thanks for the extremely informative video. I'm riding an Ultegra R8000 11spd Mechanical set-up and thought about "upgrading" my chain to a 12 speed (narrower inner & outer plates). I now know that the "narrower outer plates" of the 12 speed chain causes front derailleur shifting issues to my 11spd R8000 Mechanical (as per video proof shown). *It has been claimed that the 12 speed chains is compatible with an Ultegra 11spd Di2 system. **However, a 12 speed chain isn't compatible with an Ultegra 11spd R8000 Mechanical system- verified!

Please write a script next time. How crap you jump around more than a squirrel on meth

What position should the H & L screws be at the start of installation (screwed all the way in, out, somewhere in between?)

Superb video, very detailed and explained every step and factor. Also nice to hear a fellow West Country accent. New sub here😊

Ah the bloody lines near the tyre to set cable tension. Trust Shimano to overcomplicate the design.

Yep, i learned. Thanks.

T10 Torx bit worked for me. As a bonus, the bit survived the ordeal!

Excellent video, very helpful - thank you.

my go to video when setting up a front derailleur. Clearly explained and easy to follow.

That's helpful 🎉 thank you

The best bicycle adjustment videos so far. Thank you for your work!

Creative solution! But maybe problem(?): the GRX lever/caliper holds a BH90 hose. And is the MT410 not set for BH59 hose? How do you handle that?

I'd've used an all thread shaft with washers, nuts, and sockets instead of a hammer. Bearings don't much like hammers. Otherwise, thanks for this, there's very little to help a Mavic wheel owner on KZbin!

Thanks! Straight to the point, very informative.

Campy ErgoPower routing is so much better and no ferrules needed.

Nice video thanks for help

Very good guide. Clear and to the point.

Thanks a lot! My right (rear) shifter doesn't seem to pull up the teeth, does that mean It needs reparing? Is it possibile to repare? Thanks 😊

Cheers great video

I have this same hub on my 2015 Cannondale Synapse. I've been looking for replacement bearings but so far haven't found any place on the web that sells bearings listed for this exact hub. The Mavic website doesn't seem to have these for sale and ebay lists bearings that supposedly fit Mavic wheels but don't specify bearings for the Mavic Aksium Disc Rear Wheel. Do you have a part number or some way of specifying which bearings I should order?? Also when I hold the rear brake and push the bike back and forth under pressure there is a popping sound kind of like spokes might make if rubbing together but I can't find any loose or broken spokes just that weird and rather loud snapping sound. Thank you for your great video by the way!!! One of the best instructional videos I've found, very clear and concise. Excellent job!

ST-R8150 specs say the shifters have only 2 ports actually, not 3? But that should still be enough to implement the wiring you explain?

Another excellent explanation! I just want to add with boost spacing AND the use of wide tires (2.6, or more, wide), the top of the chain has to clear the tire. So even if the chainring clears the frame, you may still need to push the chainring outboard for the top section of the chain to clear the tire. This can happen due to short chainstay lengths.

What about 12 speed cassette with 12 speed chain with 11 speed RD + FD + Shifters + chainset? Any idea?

Esté sistema es compatible con mi bicicleta Fiji de carretera modelo gran fondo 2012 gracias

It increases how much % of performance from 8s?