Витя где находится твоя мастерская хочу приехать к тебе починить lexus случайно не в Калифорнии?
@Viktor_G_Automotive9 минут бұрын
Unfortunately I am pretty far away from you, in Canada :)
@streaminskeleton55156 сағат бұрын
Hey Viktor. Ty for this Video. Just replaced the shocks on my RDX due to left rear noise when going over the smallest of bumps. Fixed the issue and replacement took exactly 2 hours. Fine job sir. Video was of great help.
@Viktor_G_Automotive12 минут бұрын
Excellent work, thanks for the positive feedback!
@user-lg2hd8ht3d10 сағат бұрын
How many liters do I need to pour?
@Viktor_G_Automotive9 сағат бұрын
Hi, the video has all the information you need.
@user-lg2hd8ht3d9 сағат бұрын
I have bad English, can you please write?
@Viktor_G_Automotive8 сағат бұрын
@@user-lg2hd8ht3d 4.3 litres
@bryanfurys11 сағат бұрын
hi can you tell me how to tighen up coolant cap correctly onl lexus nx200turbo year 2014
@Viktor_G_Automotive11 сағат бұрын
You just turn it clockwise until it makes a clicking noise and stops turning: 2015-2021 Lexus NX200t NX300 All Underhood Fluids Level Inspection And Top Up Instruction kzbin.info/www/bejne/pZbUpXWjast-p7s
@bryanfurys11 сағат бұрын
@@Viktor_G_Automotive how i can contact you i live in another country but i need your suggestions... do you have email or something.. i got issue with my car i need your advice please.
@Viktor_G_Automotive9 сағат бұрын
@@bryanfurys hi, unfortunately I am unable to assist with diagnostics over the internet. If it is something simple, you can ask on here and I’ll try to answer.
@bryanfurys9 сағат бұрын
@@Viktor_G_Automotive car doesnt need diagnostic i have techstream its not that, we recently made coolant replacement for lexus nx200 turbo engine, all toyota procedures was followed , 1 electric pump was moved with techstream , other while car was started since its mechanical, in order to air bleed, after couple of days car was needed to be topped with around 2 litre of coolant genuine from toyota is this normal or there is a issue,
@Viktor_G_Automotive9 сағат бұрын
@@bryanfurys that sounds like the air was not fully bled out of the system after coolant replacement. Keep an eye on it, if there are no external leaks and the coolant level settles and does not require more topping up, you should be good.
@user-pj8of1vr6w21 сағат бұрын
Thanks and how about the water pump 2019 es300H?
@Viktor_G_Automotive11 сағат бұрын
Will do if I ever get a chance, thanks!
@user-pj8of1vr6w2 сағат бұрын
@@Viktor_G_Automotive Thanks and have a good weekend
@albertmaxwell1095Күн бұрын
Any chance to have a video how to replace the 2010-2015 RX Motor mounts? Thanks. I'd like your videos, very instructive. The best
@Viktor_G_AutomotiveКүн бұрын
I will if I ever get a chance, thanks!
@thebikedog8790Күн бұрын
Hey Victor, i have a question i need answered. 2015, RX350 key fobs have brand new batteries but only a 10-20 ft range outdoors unobstructed. Where is the receiver within the vehicle? And is there a way to boost the range?
@mariofigueroagКүн бұрын
perfection!
@Viktor_G_AutomotiveКүн бұрын
Thanks Mario!
@user-eg4jg8lo9oКүн бұрын
Is it the same way to replace the blower motor for the 2007 RX350?
@Viktor_G_AutomotiveКүн бұрын
Pretty similar
@bryanwilson5779Күн бұрын
Thanks for the video. I thought this would be an easy job but this could take a few hours. Not sure what the dealership charges but it has to be over 600 dollars plus tacking on additional jobs like throttle body cleaning. Currently I am either going to do the front half (easy part) and check the wear on the plugs to save for later. Going to look into those intake seals and see how much they cost before I start. Sometimes these parts are hard to get and I don't want to be caught with a long wait time. Thanks again.
@Viktor_G_AutomotiveКүн бұрын
You are welcome!
@paulcamalin5236Күн бұрын
Hello Viktor. As you recall I said my sunroof is a bit off and the edge of it is on the roof. That's why it can't close. I took out the motor and I saw that the railing inside the assembly that holds the motor is damaged. That's why it can't spin anymore to move the sunroof. The motor is fine. Can you please give me some advice on how to replace the whole assembly that holds the motor and is attached to the roof? I can't believe Lexus makes such a fragile plastic railing for this heavy job.
@Viktor_G_AutomotiveКүн бұрын
You have to remove the roof headliner and that will give you access to unbolt the sunroof track assembly.
@@Viktor_G_Automotive I just saw a video on youtube. It seems you a lot of work to repair the belt. To do that you need to remove the whole assembly by ripping your roof apart and then replace the whole assembly not just the belt.
@Viktor_G_AutomotiveКүн бұрын
@@paulcamalin5236 correct, it is a pretty involved job
@arielreyes12Күн бұрын
If it would come with kick sensor, would it have to be remove?
@Viktor_G_AutomotiveКүн бұрын
Yes, its supposed to get disconnected.
@arielreyes12Күн бұрын
@@Viktor_G_Automotive thanks for the quick response, appreciate it. I have a 2020 f-sport i knew about the damper, and then i realized the kick sensor was in the way
@ryanyoung75922 күн бұрын
Worked perfectly, thanks!
@Viktor_G_Automotive2 күн бұрын
Glad to hear!
@raiyanyousuf1922 күн бұрын
I have a hybrid like yourself. Is there a way to keep the engine on so the oil can circulate properly, the hybrid will obviously turn off after a little bit
@Viktor_G_Automotive2 күн бұрын
Yes, there is a way to put the vehicle into a maintenance/inspection mode which will make the engine run all the time without shutting off. I can make a video one day. Alternatively, you can just give it a bit of throttle, which will make the engine run as well. You only need to run it for 15 seconds or so anyway to circulate the oil around the engine.
@anatutech2 күн бұрын
After watching this I was able to change my own spoilt horns in about 15 mins. Thank you Viktor. I also made a video and will post my own version soon. Thanks a lot
@Viktor_G_Automotive2 күн бұрын
Nice work!
@bogdandol35432 күн бұрын
Thank you very much, very helpful!
@Viktor_G_Automotive2 күн бұрын
You are welcome Bogdan!
@BruceParks2 күн бұрын
Imagine my surprise to find you comparing the two cars I own. I bought a 2017 GTI 6-sp manual new in April 2017. It's been a joy to drive, super fun, quick, and even economical. It's a car I planned to keep a very long time but my wife really wanted our main car (we're principally a one car household) to be an EV. We picked up a 2024 Prius Prime SE this past January. It has been a joy to drive and is quicker than expected. I'm reluctant to sell the GTI but the PP is doing its best to convince me otherwise. Thanks for the video.
@Viktor_G_Automotive2 күн бұрын
That awesome that you have both and can compare them! I’ve not driven a GTI myself, but I’m quite impressed with the Prius thus far. Thanks for the comment!
@SWAYLAB2 күн бұрын
Thank you, Viktor! I was looking for the torque specs and this video solved my concern. 🚙💨
@Viktor_G_Automotive2 күн бұрын
Glad to hear you found the video helpful!
@mikeshagoury3 күн бұрын
Hi Victor. I’m trying to remove the black housing that you put the tape on, but I can’t figure out how to detach the end next to the window. Anything you can do to help me is greatly appreciated. Thank you!
@Viktor_G_Automotive3 күн бұрын
Are you talking about the whole black frame piece that the mirror cap attaches to? It’s a pretty involved process to disassemble it. It’s attached with a number of screws and clips. I’ll make a video one day, but don’t know when I’ll have the time.
@mikeshagoury2 күн бұрын
@@Viktor_G_Automotive I found another video for it, thanks! Got it done, but man, they made an unnecessarily complicated design for these mirrors! Thanks for getting back to me!
@roadanvicarstereo33003 күн бұрын
Direct emails will be blocked. My homepage has my contact information. I look forward to working with you.
@sunearth263 күн бұрын
It seems like the link no longer find the product. Could you share the parts id? Thank you.
@roadanvicarstereo33003 күн бұрын
This is Astra from Roadanvi . We are a brand specializing in car stereos, infotainment systems, and related accessories.I would like to invite you to review our products. How should I contact you?
@Viktor_G_Automotive3 күн бұрын
What is your email address?
@roadanvicarstereo33003 күн бұрын
@@Viktor_G_Automotive
@roadanvicarstereo33003 күн бұрын
@@Viktor_G_Automotive
@roadanvicarstereo33003 күн бұрын
@@Viktor_G_Automotive
@roadanvicarstereo33003 күн бұрын
@@Viktor_G_Automotive
@robyoung92673 күн бұрын
Hey Viktor, It it the same procedure for a 2017 RX?
@Viktor_G_Automotive3 күн бұрын
Not quite, the interior is pretty different.
@robyoung92673 күн бұрын
@@Viktor_G_Automotive Can you do a video for me?
@Viktor_G_Automotive3 күн бұрын
@@robyoung9267 if I get my hands on that generation RX, but I don’t know how soon that will be.
@jayl81304 күн бұрын
Hello Victor, I am wondering if you can demonstrate how to clean or replace hv battery cooling fan.
@Viktor_G_Automotive4 күн бұрын
Normally, you just clean or replace the filters, the fan itself doesn’t really require any service kzbin.info/www/bejne/naickGWabrt0hposi=M0Tjjg9pcZ_s1Mog
@steveshih46224 күн бұрын
I have a 2011 rx 450h. It’s got an intermittent rattling noise in the middle of the dashboard while driving, especially on rough surfaces. Is there anything I can do ? Any feedback would be greatly appreciated. Thanks again.
@Viktor_G_Automotive4 күн бұрын
Diagnosing and fixing a dash rattle is usually a time consuming task. You have to work methodically to find the source of the noise and then insulate the contact points with foam tape. Often the entire dash has to come out to complete the repair.
@martinalbert56534 күн бұрын
You are wearing gloves is this to keep the oil from your skin from getting on the bulb or it doesn't matter?
@Viktor_G_Automotive4 күн бұрын
Is doesn’t matter with these little bulbs, they don’t get hot enough for the glass to crack from contamination. I just always wear gloves when working on vehicles to keep my hands and the vehicle interior clean.
@oliviav73894 күн бұрын
Any chance you can make a video on removing the sliding seat carriage parts after removing the seat? So the interior space is as flat as possible without the metal pieces sticking up.
@Viktor_G_Automotive4 күн бұрын
I may do it one day, but it is a pretty involved procedure, requires dropping the fuel tank etc.
@bryantaskins44484 күн бұрын
If I buy a Toyota OEM hub assembly and wheel bearing can they be pressed together? So they sell it as one unit?
@Viktor_G_Automotive4 күн бұрын
Toyota doesn’t sell the complete assembly pressed together, but you could buy all the parts separately and ask a shop to press it together for you.
@timd55975 күн бұрын
I replaced my RDX bushings this weekend, I noticed the sway bar has a cut near the lower sway bar link end. Can that be welded or can the sway bar be replaced easily? 2018
@Viktor_G_Automotive4 күн бұрын
I suppose it could be welded. Not sure how much work it is to replace it, I don’t work on Acuras very often.
@kenyan20025 күн бұрын
Hi Viktor, I replaced my PCV valve the other day. I applied a small amount of the blue, medium, loctite. But, it did NOT screw completely back in like the original. There is maybe 3-4 mm of threads exposed. I compared the new PCV I picked up from Lexus parts counter and it’s the same size and engravings. Is this a concern to operate it not fully seated in?
@Viktor_G_Automotive5 күн бұрын
I wouldn’t worry about it.
@kenyan20025 күн бұрын
@@Viktor_G_Automotive thank you for the prompt response. Also, really appreciate all the videos you provide for us DIYer folk
@Viktor_G_Automotive4 күн бұрын
@@kenyan2002 no problem!
@jeffthimineur6225 күн бұрын
Did this now I have EPB malfunction on dash
@Viktor_G_Automotive5 күн бұрын
I mention the possibility of setting fault codes in the description under the video. You would need to clear them with a scan tool.
@jeffthimineur6224 күн бұрын
What kind of scan tool The tablet kind or a simple “code reader”
@Viktor_G_Automotive4 күн бұрын
@@jeffthimineur622 the basic code readers often don’t have the ability to access the EPB ECU, but more advanced versions and the tablet types would be able to.
@nectros84525 күн бұрын
Nice video! Well explained and professionally delivered.
@Viktor_G_Automotive5 күн бұрын
Thank you for the positive feedback!
@CoreyKnight-ri8nm5 күн бұрын
It refuses good what is it
@Viktor_G_Automotive5 күн бұрын
Sorry, I don’t quite understand your question.
@bubbatennessee75315 күн бұрын
Thank you for the detailed instructions
@Viktor_G_Automotive5 күн бұрын
My pleasure!
@shilpa19835 күн бұрын
Great Video; you mentioned you Turned the Rotors. How much need to get turned or what’s max size or thickness of Rotor need ? Beyond what thickness size left you can not turn and need to discard to buy new ones ? Minimum specification size will help.
@Viktor_G_Automotive5 күн бұрын
Hi, new rotor thickness is 28 mm. Minimum thickness is 25 mm. How much you need to machine off the rotor will depend on how warped or grooved it is. Usually they can be machined twice before they reach minimum thickness, but that will depend on your driving style and the type of pads you use (aftermarket ones often wear the rotor down significantly more than the OEM pads do).
@stephenzies88676 күн бұрын
W0W Awesome
@Viktor_G_Automotive6 күн бұрын
Not bad for a Prius 😀
@PrinceBryann6 күн бұрын
Hi
@Viktor_G_Automotive6 күн бұрын
Hello
@MADelectriCITY6 күн бұрын
Wish i watched this first! The swaybar boot was damaged when i used locking pliers on the back side of the link. I didn't need a torch but the threads were full of crud like you mentioned. Impact spun the way bar link on one side so i had to use a ratcheting box end to finish it carefully
@Viktor_G_Automotive6 күн бұрын
Yeah, removing the sway bar link is often the most time consuming part of the job.
@EM-tc6tp6 күн бұрын
Hi Victor, As always great video! I bookmark all your videos. They are a huge help in doing maintenance DYI. Thanks! I have a problem with my RX350, but my is 2016 (4th gen) and I cannot find anything on the issue I have. First, the gate started opening just half way sometimes, sometimes fully. But the other day, it got worse. No matter what method I use to try to open it, it starts opening it, goes for 3 inches, stops beeps twice and that's it. If I click again, it does the same thing, moves 3 inches farther, then stops again. On the third time when I click the button, it just closes it. What could that be? I could not find anything on that specific issue for my model. I took panel off but not sure how to proceed debuging it. Maybe disconnecting jam sensors first? Would that bypass "invisible obstacle"?
@EM-tc6tp6 күн бұрын
Looks like disconnecting jam sensor did not work. If I disconnect them, it just gives a long beep and does not move at all. I guess cpu recognizes they are missing. No idea how to proceed here.
@Viktor_G_Automotive6 күн бұрын
Sounds like one (or both) of the liftgate motors may be failing. If you have a good scan tool, you could check them for fault codes and proceed from there. If not, you would have to take the vehicle in for diagnosis.
@EM-tc6tp6 күн бұрын
@@Viktor_G_Automotive I do have scan tool and I scanned it, but didn’t found any codes. Not sure if my scanner is good enough to found those faults but I think it should…
@henley31516 күн бұрын
Hello Victor, appreciate all your maintenance videos. Can you make a video of how to locate and clean the AC drain plug for a 2017 lexus nx200t?
@Viktor_G_Automotive6 күн бұрын
Will do if I ever get a chance, thanks!
@yongqiangsong73716 күн бұрын
Honda Odyssey is a lot more easier to remove the seats Toyota really bad design
@Viktor_G_Automotive6 күн бұрын
It’s literally 4 bolts each, takes 10 minutes to remove them 😉
@sams76036 күн бұрын
Did you make trip back to calgary?
@Viktor_G_Automotive6 күн бұрын
No, I weighed the boat/trailer combo and it was almost 5500 lbs. The wife said it was too much for her van to pull over the Coquihalla, so I brought it back with the Tundra 😅
@shadowscreamer17 күн бұрын
Mine won’t turn on but the outer tail lights will
@Viktor_G_Automotive7 күн бұрын
Have you replaced the bulb already?
@shadowscreamer16 күн бұрын
@@Viktor_G_Automotive I have and thanks for the response. I’m embarrassed to say that I realized it was the reverse lights lol…my excuse is that it was after a long day of detailing and VHT tinting and buffing my lights. It was a “duh” moment
@Viktor_G_Automotive6 күн бұрын
@@shadowscreamer1 😆
@nistorsaula12337 күн бұрын
hi Victor does this box not have an oil filter?
@Viktor_G_Automotive7 күн бұрын
It does not.
@nistorsaula12337 күн бұрын
thank you
@Viktor_G_Automotive7 күн бұрын
@@nistorsaula1233 no problem
@MsAlexMos7 күн бұрын
Thank you Comrade Helped a ton :) Subscribed)
@Viktor_G_Automotive7 күн бұрын
Thanks!
@nickt45337 күн бұрын
Thanks!
@Viktor_G_Automotive7 күн бұрын
Thank you so much for your support Nick, I truly appreciate it!
@rubenflores36247 күн бұрын
Another awesome step by step video Victor, thank you!
@Viktor_G_Automotive7 күн бұрын
Thanks Ruben!
@sergiibuch8 күн бұрын
Hi Viktor, my dealership in Quebec recommends to change oil every 8k km, do you also change it every 8k? Are you in cold climate?
@Viktor_G_Automotive7 күн бұрын
I live in Alberta and replace the oil every 8K on my own Sienna.
@mariomejia17018 күн бұрын
Gracias amigo ❤
@Viktor_G_Automotive7 күн бұрын
You are welcome!
@DailyAhadeesInEnglish-fl6pq8 күн бұрын
Hi, my running light or parking light bulb is not working on the same side , how to replace it. Thanks
Can I send you a small video to show what’s wrong, where to send a video
@DailyAhadeesInEnglish-fl6pq7 күн бұрын
kzbin.infoqBoL6GY2VZA?si=27RDpxf560vxXlic
@DailyAhadeesInEnglish-fl6pq7 күн бұрын
Please check the above video and suggest, my parking corner lights does not work without brake , Thanks
@Viktor_G_Automotive7 күн бұрын
@@DailyAhadeesInEnglish-fl6pq hi, I am not able to share my email. If you are talking about the corner bumper marker light, here is my video regarding its replacement 2010-2015 Lexus RX350 RX450h Rear Bumper Lower Side Marker Light Bulb Replacement Instructions kzbin.info/www/bejne/hKeTlWdqpdB5m9E If it is something else, just search my channel, I have a video for every bulb on the 2010-2015 RX.