10 FPV VISION issues & how to fix them - hacks | MaiOnHigh

[@MaiOnHigh]

Learn how to FPV (Parts, builds, solutions, flying, laws) and how to REALLY TRAIN ("just fly more" won't cut it) www.maionhigh.com/fpv-academy

[@imsomii]

I hate setting up recievers sometimes

[@ragndroneman]

Got to be things just randomly stopping working after they were fine and the quad just not being used for a bit like I mentioned in my comment 👍

[@dougmcpheters1546]

For me is getting different cameras to adapt. I have several AKK VTXs and finding the correct connector and adapting can be painful.

[@madladdan]

The video. I have these faint lines in the middle of the feed that refuse to go away. Only happens when I run cam signal through fc to vtx.

[@MaiOnHigh]

@@madladdan that's probably caused by some electrical noise. Is your signal cable tied together with gnd? That may help

[@ИванПавлов-й8ф]

The most useful video I have seen so far. And everything is packed in a slightly more than 5 minute video. So underrated!

[@MaiOnHigh]

Thank you! Be sure to share it so it gets more traction :)

[@ИванПавлов-й8ф]

I return to this video because my video is bad again after switching to direct battery supply. I will try to add a little capacitance to the supply line, because it gets bad when the throttle is altered.

[@kerjs02]

Wow! Black wavy lines, nailed it. Motor screw was touching windings. Thank you

[@MaiOnHigh]

haha glad I could have helped!

[@imsomii]

wow... this was a nice list! Hope it helps beginners a lot! I once had the screw touching the motor and I didn't know whyyyyyyyyyyyyyyyyy it looked so bad! Like I switched camera and VTX and Antenna and everything :o

[@MaiOnHigh]

Haha yeah it's an expensive lack of knowledge 😔 I had it too once

[@gandaulf_fpv6925]

I've been flying alot more analog lately. This is always good to fall back on. Thank you Lexie. 💜

[@MaiOnHigh]

Haha yeah... You still fly analog?

[@gandaulf_fpv6925]

@@MaiOnHigh One long range and a few whoops are still analog. I still enjoy it.

[@qm2105]

Bookmarked this one! Short and right to the point! Great job! 👍

[@MaiOnHigh]

Thanks a lot! Glad you liked it 💜 I am always happy to share some quick tips to the point ☺️ I remember this is what I would love most ahen I was starting...

[@Grevil89]

Trying to work out an issue with my first build right now, and it looks exactly like what you showed as "too much noise" - will check if twisting ground and video cables, also ordered a replacement antenna. Thanks for this, it sure helps!

[@MaiOnHigh]

@@Grevil89 keep me posted!

[@GreasyHorror]

thank you for making this, very to the point and helpful

[@MaiOnHigh]

@@GreasyHorror thanks for watching!

[@betterdog]

Hey, Thanks … I couldn’t get to my camera cable attached to circuit board. You gave me the confidence to open up my frame. It was lose from board. Snapped back in it works great now…. THANKS

[@MaiOnHigh]

@@betterdog happy to help!

[@Wtf_drone_productions]

Thanks! Those 6 minutes saved my hours of troubleshooting and wondering around the internet!

[@MaiOnHigh]

Glad to hear! 💜

[@lankog777]

This video literally coverd all of the issues i had in the past (except camera falling out)! Great content, keep up with great work!

[@MaiOnHigh]

Thanks a lot! And kinda glad I covered them all 😱😂😅

[@dougmcpheters1546]

Lexi, you become such an FPV authority and such a great reference and resource in virtually every facet of the hobby. Then to have placed 8th in a heavy competitive tournament (with poor VTX reception!) is pretty darn impressive! Looking forward to more!!!

[@MaiOnHigh]

Thanks a ton! I am absolutely preparing more stuff, so don't worry! 😉

[@slowridefpv9668]

I have a quad I’m going to try twisting the video with the gnd wire. Love the quad the video is just sub par.

[@MaiOnHigh]

🤔 hmmm... Does it have capacitors?

[@slowridefpv9668]

Yes on the caps, moved the ground around, separated the wires, reroutes the wire, still see noise in the video that gets worse with the throttle.

[@slowridefpv9668]

Horizontal scrolling lines that are very faint but they are there. Haven’t flown it in 6 months.

[@slowridefpv9668]

Thought about your other comment about a regulator with an L/C filter.

[@JohnnytheBikeGuySLC]

Brilliant! I have a blown video in/out on my FC and this really helped diagnose it. Thx Lexie!!

[@MaiOnHigh]

That's awesome! Glad I could help! What do you think I should tackle next?!

[@JohnnytheBikeGuySLC]

@@MaiOnHigh I think something with similar common issues. much like this issue of video clarity. the tip about twirling the video and ground but not power cables is epic!!! Stuff like that is absolute GOLD! Ill think of a good issue for you as I work and meditate today. Love your content MIA!

[@MaiOnHigh]

@@JohnnytheBikeGuySLC thanks a lot for appreciation

[@Darckrun]

It was the power output all along, thanks!

[@MaiOnHigh]

💜

[@jakestyles002]

Great job! Well paced and packed full of info! Thank you.

[@MaiOnHigh]

Thanks a lot! I like it straight to the point 😅

[@jkpisces]

great video . never see pilots speak about these. thanks!

[@MaiOnHigh]

@@jkpisces you're welcome!

[@flipfpv]

Nice job! I always twist the cam and vtx wires together but didn't even think that you should leave out the red power wire but that totally makes sense. I would add that some lenses, like the ones on the Foxeer Predator cameras, break internally on hard crashes and can vibrate and appear as if the lens is loose even when it's not - but it's actually the lens elements inside that have broken loose.

[@MaiOnHigh]

Oh I didn't know that 😅 (never used foxeer 😂

[@nmrlab3807]

Very nice, any comments about diagonal consistent background noise? Thanks.

[@MaiOnHigh]

Would you mind sending me a video or screenshot to [e-mail]?

[@nmrlab3807]

@@MaiOnHigh Not at all, I'll be in touch. Thanks.

[@MCsCreations]

Fantastic tips, Lexie! Thanks a lot! 😃 Stay safe there with your family! 🖖😊

[@MaiOnHigh]

Thanks a lot for watching and stay safe! 💜

[@SchraubeUNDMutter]

thank you!

[@MaiOnHigh]

@@SchraubeUNDMutter you're welcome

[@fpvkevlar8101]

Great video

[@MaiOnHigh]

Thanks!

[@Lephro]

I needed this! Awesome work. Thanks a lot.

[@MaiOnHigh]

Great! Happy to deliver! Anything else I can do for you? ☺️

[@Lephro]

@@MaiOnHigh Well, the dog needs to be walked, Car needs to get cleaned .... .. :P :P :P Nah, just joking ofc.... you did so many good videos that helped me and probably countless other people. Couldn't ask for more!... ... or hmm actually.. ... maybe one thing: Never stop beeing the cool person you are! Much appreciated!

[@ragndroneman]

Last time I flew my tinyhawk2 everything was fine, then went to fly it again after a few days and just could not get the goggles to find any signal! Went into bf to check I had the right channel and frequency. Must be the vtx I think but not sure why it just stopped working! Great video btw 😀👍

[@MaiOnHigh]

Maybe you crashed? 🤔 Should be vtx if there's absolutely no signal

[@FpvBudgetBuilds]

Great info. Thank you 👍 👍

[@MaiOnHigh]

And thank you for watching!

[@fellowrc3787]

That was freakin' interesting. Infos are on point and very helpful.👍🏼

[@MaiOnHigh]

Thanks! Glad you enjoyed it!

[@grawlix4419]

It’s amazing how simple and so unintuitive issues in this hobby can be.

[@MaiOnHigh]

Haha true

[@junifferjardinez4851]

thanks for this video

[@MaiOnHigh]

And thank you for watching!

[@FlyZoneFpv]

Thanks Lexi 😉great tips

[@MaiOnHigh]

Thanks for watching!

[@andreua8779]

Meteor75pro, im loosing signal in 5-10m, in 400mw littlebit better, but when i flight to the corner of building signal totally lost😢 earlier its works well on 25mw

[@MaiOnHigh]

I'd check and change the antenna in this situation

[@GuruFpv]

There will be unclear screen at short distance if vtx goes in pitmode.i had that experience.

[@MaiOnHigh]

Ah yes, that too

[@sparky6200]

Bjork does FPV now? Awesome Is there some system or combination of components that provides the highest HD display with very little latency? Latency is my #1 problem....makes everything "feel" off. I also wan the highest HD I can get....Suggestions my Bjorky-wizard-of-FPV???

[@MaiOnHigh]

?

[@ramdonko6661]

Cheers / All helps = how about black lines going up/horizontal at higher throttle ?!? (could be my soldering :-))

[@MaiOnHigh]

Hmmm can you send me a dvr of this on [e-mail]?

[@Fizz_Gerard]

Ciao! Complimenti per il video! Breve ma ricco di informazioni utilissime! Purtroppo dopo un crash non vedo più niente sugli occhiali Quando ho ritrovato il drone(dopo 30 minuti)era acceso ma senza antenna sulla vtx. La vtx si accende indicando i canali ma se faccio la ricerca automatica non trova nulla di visibile Nemmeno l'osd Potrebbe essersi bruciata la vtx perché è rimasta accessa senza antenna? Hai qualche idea da darmi? Grazie in anticipo Un saluto dall'Italia😊

[@MaiOnHigh]

VTX burned. You need a new vtx. They burn without an antenna sometimes as quickly as within seconds 😅

[@Fizz_Gerard]

Grazie mille per la risposta!! Anche se si accendono i led dei canali pensi sia bruciata quindi?

[@iammeobviously6815]

Help! My camera (bf C02) overheated (sitting there, drone plugged in) while I adjusted settings. The image had a blue tint, and after I let it cool, it was back to normal‽ Did I damage anything????

[@MaiOnHigh]

@@iammeobviously6815 don't let the vtx or camera stand there plugged in for too long 😅 It may be happening, yeah

[@iammeobviously6815]

@@MaiOnHigh ok

[@PrgProplay]

Mam can you solve my problem I have a video transmitter of ts832 (ROTG01) model and when I have connected to the uvc video receiver with my Android tab then when the transmitter and the receiver connected with the same channel (i.e,.5584M=5584M) only the audio is transmitted from the transmitter and received in my tablet . After few and quick tries when I have connected with the video also it is a difference between 361 GHz between The frequencies of the transmitter and receiver(i.e,.5584M=5945M) which gives me very less range about 30 to 40 m but the audio range is mainly about 1 km to 5 km so how to resolve this problem mam please help me .. I also have videos of this issue on drive should i give the link to you ?

[@MaiOnHigh]

Hey! I never transmitted fpv to a tablet but shoot me an email with the video to [e-mail] It may be an issue I can solve

[@dailydronejourney]

nice info, I got issue no 1 and no 2.. :(

[@MaiOnHigh]

Well! Hopefully you know how to solve them now 💜

[@clazy9222]

When it is a grey back and you have don't osd it can also a antenna of your google, this peoblem i had a long time, and don't know why i have this problem...

[@MaiOnHigh]

Never had that. Usually antenna's issues mean either snow of small range 🤔

[@clazy9222]

@@MaiOnHigh yeah that i thougt too, but in the end it was my patch antenna. Every time I flew a little farther away, the picture suddenly disappeared and suddenly turned gray no one could explain exatly to me why. Finally I came to the conclusion that it must be the antenna. Then I took off the patch antenna and now i flew about 5 times without problems. Now I hsve to get a new patch antenna... (I have to say, it was a very cheap one before)

[@joeasciutto5770]

My fpv feed breaks up at about 50 meters on 350 mw, is this normal? Help would be much appreciated. 👍

[@MaiOnHigh]

Have you tried changing the antenna? Sounds like an issue there. Does it just break to nothing? In random or just within that range? (Like always when you are further away)

[@joeasciutto5770]

@@MaiOnHigh i watch videos of people with the exact same setup and vtx, (hglrc Zeus nano) and they get much better range and less flickering on the fpv feed.

[@joeasciutto5770]

I tried to change the output power and that didn’t do anything either. Even when the quad is relatively close to me, about 2-3 meters, the screen flickers and cuts out heaps. The antenna that I’m using is a pig tail, should I use a different type?

[@MaiOnHigh]

@@joeasciutto5770 this actually sounds like a broken vtx if it flickers in such a close proximity. Would you mind sending me some pics to my email? [e-mail]?

[@joeasciutto5770]

@@MaiOnHigh I sent a clip, tell me if you get it

[@badder9492]

i had black lines because i had vtx antenna cable close to camera cable

[@MaiOnHigh]

@@badder9492 that can also happen

[@davidmartins1854]

I have other issue! In my osd I have the consumption of mah and they go up, really crazy and I am just stopped...

[@MaiOnHigh]

Well that's pretty normal when you are pushing a lot of throttle. Or is it way too crazy? You can send me a dvr on [e-mail]

[@Binkoro]

What if have good video feed but no OSD? Everything in Betaflight is set up correctly.

[@MaiOnHigh]

Are you setting up the osd from fc or the camera?

[@Binkoro]

@@MaiOnHigh from the fc

[@Binkoro]

I think the OSD chip is defective even the the FC is brand new

[@rotorfpv4117]

I very often be nervous flying digital fpv because of failsafe posibility (eg. plug off the cable of gogles). Mam nadzieję, że dobrze to wyraziłem :) Ale w fpv jest mnóstwo niebezpieczeństw, szczególnie jak nie mamy gps a nawet jak mamy, jest nieprzewidywalny.

[@MaiOnHigh]

Haha prawda

[@JP-qq2kn]

You forgot 1.. if you see only black on the screen, REMOVE THE LENSE COVER!! 🤪

[@MaiOnHigh]

Hahaha true 😂

[@bonnet1994]

This happend to me then I removed the cover and still had black screen. Turned out my video In and video out pads had given up

[@022fpv]

I got reddish video after replace the camera lens. 😢

[@MaiOnHigh]

That may be a sensor issue or power issue

[@022fpv]

@@MaiOnHigh thank you very much

[@sorellebankson2479]

I remember once having the worst vibrations on my quad that none of the other pilots could resolve... (no one heard it, no one knew what's wrong... We switched props and stuff) At the end one of the guys was like: "Hey, is it a lens?" And he just screwed it back in 😐

[@MaiOnHigh]

Hahaha I can imagine everyone's faces! 😅😂🍿

[@TheXanthoman]

Ive got an fpv issue , wherever i go , ive got a vision of this really cute fpv girl that i just cant get out of my head . I did check my screws and i think ive got a few loose . 🤖

[@MaiOnHigh]

Smooth... 🤫

[@SirCreepe]

first

[@MaiOnHigh]

noice

[@THEORGCHANNEL]

Nice 👍 I was too busy today

[@kimgudboi]

shizz I have 3 of the 10 issues lmao!

[@MaiOnHigh]

haha you know how to repair them now though, right!?

[@THEORGCHANNEL]

NOT first 😥

[@MaiOnHigh]

😔 next time?!

[@THEORGCHANNEL]

@@MaiOnHigh 🤞🤞

[@TheXanthoman]

😍😛

[@MaiOnHigh]

☺️

[@borawskikrzysztofkali77]

comment 😉

[@MaiOnHigh]

Algorithm thanks you 💜

[@borawskikrzysztofkali77]

@@MaiOnHigh you welcome 😉

[@MaiOnHigh]

@@borawskikrzysztofkali77 💜☺️

[@AlwayslookingNeverlookedfor]

Thank you so much

[@MaiOnHigh]

You're welcome