10EE part 20b

[@peterbrandes5166]

One of the best rebuild series I’ve seen on KZbin in a lot of years. Keep it up!

[@fourpondsshop7940]

Wow Peter! That's an awesome compliment!

[@darrenblattner2508]

The finish on the cross slide is fine. The apprentice marks are acceptable also as thats part of the history of the lathe. Very nice rebuild, I wish I had half of your patience. Keep smiling

[@fourpondsshop7940]

Hi Darren thanks for checking out the channel! I appreciate your comments. I like the characterization of the cross slide damage! It's a positive way to look at it!

[@mikescott4007]

The machine is looking beautiful! Can you say that about a machine oh heck why not! hey don’t forget to keep me on your list of people interested in the 30 inch

[@fourpondsshop7940]

Thanks Mike! You most certainly can say that about a machine if it truly deserves it! And I think the 10ee does

[@glennstasse5698]

Before and after shots are great and gotta make you feel great, too.

[@fourpondsshop7940]

Hi Glenn, thanks for watching and commenting. Yes, it's been a very gratifying project.

[@ActiveAtom]

We see we are joining Outside Screwball here as a pair of new subscribers here, we love the Monarch 10EE only as a GREAT machine, thank you for making these videos. Lance & Patrick.

[@fourpondsshop7940]

Thanks guys! Appreciate it!

[@russkepler]

When you check the slack in the cross feed screw and nut be sure the taper bar is clamped on the back of the taper attachment. There can be a little play there. In any case .006" play there is not bad at all. BTW: The 10EE is designed so that one wrench is required for all normal operation, a 9/16 open end and 3/8 square end. There are several makes and you can find them in ebay. I've aligned the slide in mine, just remove the chip shield on the headstock end and mount an indicator to the bed referenced to the slide. Adjust the swivel so the headstock end is centered and the other is on the 0 mark. Run the carriage back and forth and adjust for 0 on the indicator using only the cams on the headstock end.

[@fourpondsshop7940]

Russ.. Very helpful info... Thanks!

[@waynep343]

when you get the taper attachment rod holder made up. be sure to lock the taper adjusting knob at 0.. and the taper guide at zero thru the lens.. then run the table back and forth with the dial indicator on like you did with at the end of the video.. then adjust the 3 eccentric screws on the taper attachment so you get ZERO crossslide movement when going up and down the bed.. on the eccentric screw bearing preload against the slides.. those probably have to have a significant amount of force to prevent the tool bit from pushing the crossslide and taper attachment back from the workpiece..

[@fourpondsshop7940]

Thanks for the setup info!

[@mikepelelo5657]

Nicely expedited! I'm really enjoying this series.

[@fourpondsshop7940]

Thanks Mike!

[@Anotherhomeshopguy]

ps. awesome before and after shots!! wow.

[@fourpondsshop7940]

I saw that on another channel and it really stood out so I wanted to include my before pictures

[@kimber1958]

Very nice job

[@fourpondsshop7940]

Thanks!

[@bid6413]

Adjust the taper attachment using the 3 cam adjustable screws so the taper attachment move parallel to the bed ways? Another great video filled with good information and tips. Thanks. Cheers, Will

[@fourpondsshop7940]

Thanks Will, makes perfect sense!

[@kimwood7718]

I have the bed clamp for the taper attachment and can get you a dimensioned sketch...., I will trade you I am missing the rod on mine and would like the dimensions thread size etc for that. Enjoying the series thanks for all the effort you put in to share your experience.

[@fourpondsshop7940]

Hi Kim, thanks for the offer! I'll send you dimensions for the rod this week

[@kimwood7718]

I have taken some.3 view photos and have a PDF dimensioned sketch

[@kimwood7718]

How.would you like me to send them?

[@fourpondsshop7940]

Hi Kim.. Can you send it to [e-mail]. Thanks!

[@Randallvgc]

Kim, could you send me the photos and PDF sketch? Thanks [e-mail]

[@outsidescrewball]

enjoyed...great video production/discussion....if you don’t get an immediate answer to your request let me know as I have a couple of sources local

[@fourpondsshop7940]

Will do

[@mikebowling3228]

Try turning the shields for the taper attachment over I think you may have them upside down. I do have an original clamp for the taper attachment rod, I will send you some photos and dimensions of it.

[@fourpondsshop7940]

Thanks Mike! So according to the drawing in the monarch manual, the way I mounted them is what's shown. Do you have a picture of your suggestion?

[@Randallvgc]

I could use the measurements for the clamp too. Please let me know. Thanks!

[@pauldepilotpaul]

Another great episode! This is going to be an awesome historical reference. Just a thought, if someone has the part that we need and they would be willing to take pictures of it against a rule. Then I think we could 3D model it and make a pattern. Who knows, maybe Clark @WindyHillFoundry would be interested in a collaboration.

[@fourpondsshop7940]

Hi Paul.. Someone commented a link to the drawing on practical machinist. Looks pretty complete

[@kimber1958]

It gives it character

[@fourpondsshop7940]

I think your right.. You should not always erase history.. It tells a story about the machines past!

[@outsidescrewball]

I stopped by my buddy’s house, he gave me (I borrowed) the original part along with a made part, happy to photo and measure for you, just send me an email to outsidescrewball gmail

[@fourpondsshop7940]

Thanks Chuck!

[@simonsaelaertfurniture9883]

nice work, i m restoring mine at the moment. You still need the drawing of the clamp?

[@jackpledger8118]

If there is a source for a casting of the taper attachment bracket...I need one also. Great video. A lot of very good information. Not much in the manual from Monarch.

[@fourpondsshop7940]

Thanks Jack!

[@alonsoarteaga5056]

Hi love watching the rebuild process, I have a question, im in the process of rebuilding my taper attachment on my I/M 10EE. What bearings did you use for the top piece on the taper attachment. The piece with the closely coupled 4 bearings. And are they the same as the bottom 4 bearings on the main casting? Thank you!

[@fourpondsshop7940]

Hi! So I'm pretty sure I got those bearning on Amazon by using the number on the bearings. I figured they are rarely used and of course low speed so the quality wasn't a big concern. The original bearings were very gritty and had stiff places so they really needed to be changed.

[@Anotherhomeshopguy]

an awesome look into how that taper attachment works!! I'm no 10ee expert since I don't own one...(YET! lol) but I think you're thinking along the same line as I am.....since there was one fixed setting and three adjustable and the fixed was on the side attached to the lathe, I would assume once attached on the lathe you use one adjustable on the side of the lathe to adjust the channel to be parallel with the bed ways, then use the two outside ones to adjust for preload/slack? regarding the missing casting, If I had the 30, I could probably borrow a buddy's and send it to Cattail foundry to have a few copies made. =)

[@fourpondsshop7940]

I believe you are correct.. A couple of other folks posted similar thoughts

[@williamwilson9815]

Great video. I had one question related to the rod on the taper attachment. I am having to pickup missing parts for my taper attachment on the lathe I just purchased. What does the part look like that the rod screws into on the bottom side of the taper attachment frame? I just have two holes on each end with nothing in between. Thank you

[@fourpondsshop7940]

Hi William, On my lathe, the rod threads into a threaded hole right next to the way wiper closest to the lathe frame. Let me know if you need more info...glad to help

[@russkepler]

Taper clamp dimensions: www.practicalmachinist.com/vb/monarch-lathes/source-10ee-taper-bed-clamp-274429/#post2148764

[@fourpondsshop7940]

Thanks Russ.. Got it

[@profuse007]

Who's the engineer that designed the 10EE? Need to make a statue of him

[@fourpondsshop7940]

Ha! I agree!

[@kennethrenton9298]

Have you received the dimensions for the taper attachment bed clamp yet? If not I have one that I'd be happy to measure up for you.

[@fourpondsshop7940]

Hi Kenneth...so yes I did..thank you!. In fact a viewer actually sent me a bed clamp which I am so appreciative of!

[@pauldepilotpaul]

There is a thread on Practical Machinist Forum posted by "Vettebob" from 2017. He casts the brackets for $100. It doesn't appear as though he has posted in a while. Maybe someone has his contact info?

[@fourpondsshop7940]

Thanks Paul!