1742 The Rocket Stove - Explained and Demystified

Don't forget to check out Luke's channel found here / @tntomnibus
If you want to have a look at those special videos become a member and join by clicking this link / @thinkingandtinkering
Don't forget that you can buy my books and materials for your own experiments including our conductive inks at secure.workingink.co.uk/worki... - and for the many who have asked, yes, you can also donate to further our work, again through the shop.

[@markusmuller5318]

Another point that is often missed: An ordinary wood stove, once the burn is established and going, burns its wood on the entire surface of the firewood. The rate of burning is mainly controlled by the reduction of the airflow to the burn chamber. This leads inevitable to a less efficient burn. The Rocket Stove on the other hand burns its fuel (if done/loaded right) always with the maximum amount of air it can possibly get - but only at the tip of the firewood. As I said, a small detail often missed out concerning Rocket Stoves/Heaters and their efficiency. Greeting from Germany - love your channel!

[@emel60]

I've never looked at it that way- that reduced airflow automatically lowers efficiency in the woodstove. Now you've answered a question which was baffling me for some time. With the addition of secondary air intake in my tall woodstove (see my channel), in the form of a vertical pipe, the fuel always burns. Now, the pipe is too perforated to create a proper secondary combustion (I guess the superheated air cools by the time it travels up just enough to not burn), but the bottom perforations always provide some air, along the primary air. So I incidentally made a hybrid. It gets it really hot, but I also have increased fuel consumption. A win win, depending on what one wants. Thanks bud!

[@modelnutty6503]

yup, and the burning end runs bright yellow to white hot as it gets, is a LOT more heat in shorter time from same amount of wood.

[@emel60]

@@modelnutty6503 as Mr. Robert said... A log of wood is a log of wood, same energy in two cases, but one does it faste, with more power. My tall stove has relatively thick chamotte bricks inside, about 35 mm, all around the combustion chamber, and 0.5 mm stainless steel body on the outside. The cast iron top (or head) is about 2-3mm, quite thinner, and it is on the receiving end of all the fire and heat. So it irradiates heat into the room quite quickly (especially with the addition of the stove fan), and then the brick mass below gets hot, and stays hot long after the fire dies out. That was a more elaborate explanation of my 'hybrid' term from the previous post.

[@sailaway8244]

Another thing to consider with wood stoves burning on tick over, particularly overnight, is that it's drawing in cold air from outside potentially cooling the space as much as heating it (unless fitted with a direct air system)

[@lanichilds2825]

Hey if it burns left to right wouldn’t that be good for thermoelectrics? Cause isn’t it the difference in temperature that causes the electrons to go to one way?

[@mechanicallyseparatedspiri8638]

Working as a welder in stainless steel a while back I made a small rocket stove, 2x2inch sq tube. I then put the stove inside a box, intake and exhaust flush welded to two sides. I added a spout to one end, and a handle to the other making a tank that holds about a gallon of water that can be poured easily. Great camping stove, I can boil tomorrows water while I cook tonights dinner, with only a few handfulls of twigs.

[@chrisbearden1331]

That sounds interesting! Would you mind posting a pic or video of it somewhere? I'd love to try out your idea.

[@ThinkingandTinkering]

nice

[@longllamas]

This is exactly what a Kelly kettle - Thermette is :)

[@loganvetsch8979]

I do blacksmithing as a hobby, and to make charcoal for my forge (I’ve since switched to propane), I settled on a method which involved a large pipe, about 3 feet (1m) long, 2 feet (65cm) in diameter, and 1/4 inch (7mm) thick, resting on 3 inch (8cm) metal spacers to allow airflow. I’d build a small fire in the bottom, and once it got going I could throw in bigger and bigger pieces of wood, filling the pipe right up. The heat from below would bake the wood on top and release gas, which would burn as long as the bottom wasn’t clogged with ash and debris. The flame from the burning gas could get up to 4 or 5 feet (over 1m) above the top of the pipe. And large spots of the pipe (which is quite thick, remember) would actually glow cherry red. To stop the process I’d remove the spacers (easier said than done) and place an oil drum with its’ top removed upside down over top of it to smother the fire. It was quite interesting, and I did my best to use some of the principles of a rocket stove.

[@AG-yb1lm]

Another GREAT Conversation! Thank you for sharing :) Regards.

[@ThinkingandTinkering]

Glad you enjoyed it!

[@grandenauto3214]

The best explanation I’ve heard for a stove…. Thanks

[@ashleysmith3106]

We have a Slow Combustion (pyrolysis) stove for heating, and a bloody great hub off a harvester outside as a "fire-pit" for enjoyment, because when its all said and done, there's something cathartic about staring into the dying embers of a mallee root open fire! Greetings from rural South Australia from a fan of your channel; thanks for such interesting content.

[@hansjansen317]

The Fin oven is a kind of rocketstove with downdraft. Very popular in Scandinavia. With downdraft section the hottest gases will stay in the upper chamber, while colder gases that did their job, leave through the chimney. In the eighties I visited a monastery in Kyiv, they had a HUGE wood fire oven in the cellar. The heat was trapped in a second "stove" consisting of just a hollow structure. Heat was dissipated in the walls, somewhere on the low side of this chamber was the escape for the gases. This construction continued for six floors. They started heating in August and only beginning of October the walls started radiating heat on all floors. Very huge stove, very huge monastery, very impressive! In March they stopped heating, the monastery kept warm until the beginning of May. The monk who designed the stove was Kuznetsov, so they called it the Kuznetsov stove. Built somewhere in 17th century. Apparently the system to preserve thermal energy by downdraft was known when they built the monastery.

[@ronwinter3290]

I would love to see a occur if diagram of the design

[@kerrryschultz2904]

In British Columbia Canada off of Highway 5a that goes from merrit bc to kamloops bc is a buddist monestary that is called the birken forest monestary if i recall correctly the name. They get winter temperatures down to minus 30 degrees Farenheit. COLD. They heat a 10000 sq. foot building with 2 smallish wood stoves, because the building is superinsulated, and sliding insulative doors cover the windows at night. Very interesting video.

[@SynapticTransmission]

The barrel part in your Mass Rocket Heater example releases heat right away - no waiting for the "Mass" part to capture, hold and release heat later over longer periods of time. That's the way I understand the system anyway. Terrific channel!

[@ThinkingandTinkering]

yeah pretty much spot on mate

[@modelnutty6503]

exactly, and a bit more than half the heat is stored for the slow release. the pipes don't load up with creosote quickly like a regular wood stove but cleaning access for the mass pipes is still needed.

[@KeithOlson]

@@modelnutty6503 Not a lot of cleaning is needed. I watched one video where a water heater RS was taken apart for inspection, and, after two years of constant use, the chamber at the top of reburn chamber only held a half-inch or so of dry soot/ash and no creosote at *all*. From what I've seen on most mass heater cleanouts, a compressed air hose is all that is needed to blow out the small amount of ash produced during the first 5-10 minutes of each operation. Most just have a small door at the end of each straight section to facilitate easier cleaning.

[@justinw1765]

@@KeithOlson I'm planning to build my rocket stove outside and pipe in heated air from a secondary, smokeless, horizontal "chimney" that will go through an opened window (obviously it will be modified to still insulate and to accept a pipe through it). So even if creosote etc was a potential issue, I would be A LOT less worried about it. This rocket stove will be so well insulated that I don't care that it is not directly inside. It will be insulated primarily by a combo of vacuum insulation and fumed silica. (Two of the most efficient insulators known to humanity, but with aerogel in between these on the scale [but aeorgel is far too expensive for me to use]).

[@coolloser85]

I was looking for someone to explain in great detail why its better how it works and the history behind it. You sir are amazing for this

[@roosteroriginal6458]

Best explanation ever! Thank you!

[@mikecondoluci53]

YOUR VIDEOS ARE THE BEST THANK YOU

[@Drjtherrien]

The issue of balancing different contrary demands is the essence of engineering. Very nicely presented!

[@fredy796]

If I only could send you a small video from. 2 years ago..a ramshorn in a so called pizza oven.. super insolated control of slow fire and adding a lot of stones around.. later introduced a heat transfusion with a water spiral to feed the CV. I left the guy with whom. I shared my suggestions and support because he had1000 things else to do. This is a hell of a product. I stil love this hell of a fire stove so easy burning..you can open the heart and the oven without danger or distirbance. Ideal Too hot for a single simple home.. You ll have to share with neighbours. I wish I could send you a video.. Thanks for your concerns and information. I love it, Fredy

[@brucereichert6509]

Watching your videos helped me refine my tire burning heater, so it doesn't give off black smoke anymore. It burns clean and since used tire are nearly free, I can heat my garage for a lot less and tires don't need to be seasoned to do the job like wood does. And there is a benefit of keeping tires out of landfills and free scrap metal to cash in at the metal recycler.

[@exbrownj]

Any pictures or information on your tire stove?

[@brucereichert6509]

@@exbrownj I'm thinking of building them for people in limited quantity locally. I can't add pictures, but I can give a basic explanation of how it works. It is a 2 stage burn. The tires have their own burn area controlled by air intake vent. A small fire burns the tire just enough to create flammable black smoke. That smoke is channeled into the vortex inlets of the rocket stove. And the whole set up is enclosed and the heat is vented into the garage. So far the only problem is that the tires burn much longer than the wood in the rocket stove, which means if the smoke isn't being burned up it will go out the chimney. I'm thinking about using propane to keep the flammable smoke from the tires ignited or cut back on the amount of tires I burn. Make sense to you?

[@angelusmendez5084]

Great class 👏 Thanks!

[@ThinkingandTinkering]

cheers mate

[@maxkennedy5073]

Rocket mass heaters have the advantage of giving a portion of instant heat, at least the ones with the steel drum in the build and storing the excess heat in the mass thereby utilizing the most efficient fast hot complete burn. A lot of the energy in wood burnt in woodstoves that are damped for the evening goes up the chimney as smoke and soot. If it didn't loose that energy you'd not have the phenomenon of a chimney fire. Exhaust from an RMH is also often at about 40C (100F), significantly lower than a wood stove so retained heat efficiency is also improved. Thus a few of your comments were just a bit off the mark.

[@mfr58]

A big advantage of mass heaters is that they produce radiant heat not so much convecting hot air which can be lost easily, when doors open and to the ceiling. They transform, fast high temperatures (as you say) into much lower temperatures for long periods, that are more amenable to body comfort and health....a problem with metal box, high surface temperature wood burners is that dust burns on the hot surfaces and is convected into the air resulting potential respiratory issues, also the fierce heat drys the air causing further problems. The Roman Hypocaust and the ubiquitous northern European masonary or tile stove have much to recommend them for space heating purposes, albeit they take time....

[@chrissscottt]

I like the idea of capturing and radiating as much heat as possible so I intend to experiment with those stacked 240 litre steel drum wood burners I've seen other pyromaniac youtubers build. I think they're referred to as 'double barrel wood stoves' but I'd like to continue stacking.

[@ThinkingandTinkering]

yeah I like that idea too mate - do a video!

[@jamesross1003]

Thinking it is a good idea. I would be interested in hearing your results. The more you can do with the same amount of fuel the better. For example, don't just heat a mass also generate with a thermopile at the same time and cook as well. The more you do with the same amount of fuel the more value it holds for you. Keep thinking like this!

[@modelnutty6503]

hmm.. rocket stove into a couple fire brick lined 30 gallon drums?

[@ricos1497]

Cairn of Dunn croft permaculture has a reasonable set of videos on a mass heater, worth watching.

[@Debbiebabe69]

Hold on.... mass heaters still exist in 2022??? I remember in the 1990s helping a family heating business, one of the things we often did was rip out the myriad of mass heaters put in houses in the 1950s and 1960s, when electricity was indeed cheaper overnight. I dont know of anyone installing a 'night rate' meter in a house from the 1970s or beyond!

[@rhiantaylor3446]

Robert, as you say, the key attribute of a Rocket heater is the efficiency and the clean burn of the gasses given off by wood in the initial fire. I assumed that it would be beneficial (necessary ?) to insulate the chimney to encourage that secondary burn to reach the temps of 600-1200 you mention. That then leaves you with some pretty hot gases coming out of the top and, by enclosing the chimney with an inverted can, you retain the heat to help keep the chimney hot but also radiate into the room and (for a rocket Mass heater) exhaust into a further heat recovery and storage area viz. the "mass", extracting most of the heat from the exhaust before it leaves the building.

[@boblordylordyhowie]

The Rocket stove or "J" stove was invented by a French inventor (whose name has mysteriously disappeared from Wikipedia) in the 1700s to reduce the amount of fuel to cook with, in the 1980s it was rediscovered and used to heat houses. House fires work on a 7:1 ratio the fireplace is 7 times bigger than the chimney but often it was temporarily converted to a rocket stove by draping a newspaper over the fireplace to reduce the ratio. The rocket stove is designed as a 1:1 stove but putting firewood into the inlet can reduce that further to 0.5:1 giving it the classic roar. I use storage heater bricks for my stoves as they hold the heat better and are easy to build.

[@Milkybar3320011]

The age old question, efficiency, coal/nuclear power stations are 35-40% efficient, so any process, burning wood, wind turbines etc don’t need to be super efficient. I’ve seen lots of comments saying why bother, it’s the fun of doing that makes it worth while.

[@Warriorking.1963]

Excellent video and very informative. Thanks also for responding to the message I posted on yesterday's video, regarding 100% carbon felt; I'll be sending you an order in a few days.

[@paulwheaton]

A rocket heater (without a mass) is good for a woodshop. A rocket mass heater is good for a home. A typical rocket mass heater puts out 70% as immediate heat and the rest into the mass.

[@joeferreira657]

Well explained, nice one Robert, thanks for your knowledge, really needed in meany countries, small rural areas.

[@MVSuances]

Hi from Spain Very interestiing video I made a belt batch box one year ago and in my opinión you are right on some points but you forget others It is true you must think about what do you want to warm and how quick If you want quick Heat The belt batch box solution is better than others because you have direct Heat as a conventional wood STOVE and in about 15 minutes you can have a clay máss Heat just above and radiate this heat On the other hand you forget that the clay dry and clean the room and you can fell a Very confortable Heat Finaly you forget that if you dont have a lot of money the batch box can use cheap wood like rest of wood cuts or even wood fron old fornitures because the pyrolisis burn the smoke Thanks and Buenos Días !!

[@kajlauritzen9765]

We had our masonry Mass oven built in 1995. Of course it needs a little bit of maintenance once in a while but it still functions perfectly. It was expensive, and of course these heaters still are, but very efficient. We have outdoor temps around 15 dgr C at the moment, and using about 15 kgs of wood we have heat for two days. The disadvantage as you mention is that it takes hours before heat comes out of the 2.3 tonnes of mass , so if we are away for several days it takes time to get some heat. But anyway, best investment ever. The upper chamber where the gasses burn acts as a cooking oven when the fire is out. A rocket mass heater can be built much cheaper and may be just as efficient.

[@MysticMCWizard]

Great vid, and your comments were bang on the money. Rocket stoves can be built from many types of materials for all sorts of reasons, all giving differing outputs and all working on the same basic principle as you discussed in your vid.. It's not always, however, the hotter it gets the more robust and thicker materials you need. It's sometimes how fast you can dissipate the heat from the device to stop it melting.. in my experiments (using tin cans) when I insulated the fire tube part of the rocket stove, it started to melt the tins, but the un isulated version did not as it was able to dissipate the heat to its surroundings, saving the tins from melting (great radiant heater, not quite so good for cooking on) but like you also said it burnt hot and fast, and when the fire went out it also got cool very quickly.. (my reasons to build a rocket stove were to make a greenhouse heater on the cheap. My experiments led me down the hot and fast burns with vortexes etc etc which were not appropriate for my needs and i ended up going down the route of a slower burning mass storage heater type rocket stove, using wood kitty litter pellets as a replenishable fuel source (a heat battery if you wish .. lol)) that slowly but surely kept my plants warm over winter without overheating and drying out the air. Also in my experiments, I found you need to get the air fuel ratio right as you can end up not getting your secondary burn to work well and end up filling your garden with smoke - stinking the place out with unburnt wood gas. Not ideal! Thanks for sharing your views and I agree with your comments. Great work! Looking forward to your next vid as always.

[@AndreaDingbatt]

I hope all is well with your greenhouse! I used to have a wonderful little rocket-stove that was outside of my greenhouse, it used to have a radiator that went twice around the inside of my grapevine and early* (sorry, I have the names on the tip of my tongue,but right now can't remember, *Yeargh!) It was brilliant, and I used to almost live in my garden!! Cooking on it was a joy, as I could avoid my mother!! In the summer, I used to have huge,sweet black grapes, and I live in the North West UK!! (Damnit, mother had the whole lot torn down after I was gone!) It was built by the Victorian who had built the house originally!! And,was an engineering marvel!! Best wishes, Andrea and Critters. ...XxX....

[@ThinkingandTinkering]

nice points mate - thank you for taking the time to post them and food for thought for me - just awesome - cheers

[@allanwood3562]

Rocket mass heaters usually incorporate a very hot radiating section (often the end of a 200l drum) before the gasses move on to heat up the mass. Flue losses are minimised as a result. A rocket stove gets hot for sure but flue gas in a room is undesirable so a flue is then required. One needs to harvest that heat before it's all lost to the outside world. For what it's worth a operated a solid fuel heater laboratory for many years and I can guarantee that the highest efficiencies were at the slowest burn rate where the mass flow of gas had a greater chance of contributing to a rooms temperature.

[@justinw1765]

Agreed on most of the points, except for one. You don't have to get really exotic and expensive to contain a hotter and more efficient rocket stove. Modified cob over stainless steel or glass works pretty good. By modified, I mean something like, instead of sand, you use a combo of fumed silica and diatamaceous earth to up insulation. And you still use some perlite and straw (or better yet, fiberglass cloth or strands for the structural part of things). Good clay can take quite a good amount of heat and over longer periods of time than steel, especially non stainless steels. I guess clay can be kind of expensive for some folks, but not really that expensive and especially not exotic for most people. The beauty is, just use some cheap steel or glass and protect these with a layer of well insulated clay (modified cob), and then you don't need much clay (rather modified cob). It's a type of composite's approach. Composites are a beautiful thing, balancing the weaknesses of different materials with the strengths of others and vice versa, so that you get a higher functioning synthesis material. Or, the whole is greater than the sum of the parts. (This connection/integration/synthesis is a material reflection of what I call spiritual truth--that of unity and connectedness [which, is really, the consciousness of Love], which I think is the heart/core of the so called "spooky action" of quantum physics. Newer physics strongly suggest what mystics from all over the world and various faiths have been saying for a very long time--everything is interconnected on a fundamental level. How else can things like quantum entanglement and Bell's theorem exist? It's really almost a "duh" if you think about it objectively and logically). And ultimately, the reason to up efficiency through things like better and well placed insulation, is so that you need less fuel to burn to get the same amount of energy out. Why not maximize this, so you can just run it on sticks and debris, rather than split logs and the like? In my yard, we have A LOT of the dreaded "gumballs". The bane of my spouse's existence apparently (she likes walking around barefoot etc), but, a potential fuel with its own aeration design built in.

[@Good4All4Good]

DEF: rocket stove - "a tube, to contain the pyrolysis gas, to give that gas a chance to burn, before the wind blows it away." 😊

[@mafferik6]

O no Robert, you missed out on this one. because the rocket stove generates a hotter flame in the tube everything is burnt better/cleaner. a mass heater does generate heat immediately throuhg the barrel that's on top of the j-tube.

[@lii1Il]

Well said! 60k-90k BTUs per log. Use it in an hour or 24 hours Their is something to be said about being able to burn almost all the fuel, but as you stated at the cost of a shorter life of the stove or complexity and/ or expensive. However, creativity and knowledge is what we're all about and being able to discover the hidden art of making materials that will extend the life of the stove, mass heater at those higher temps increasing the effective usable BTUs is just plain fun and exciting!!! I personally would love to see a mixture with relatively easy to make materials (the secret recipe) to make one that will not only last but utilize that extra 40-85% BTUs. At the same time I have no problem with those who could care less. Lol

[@KeithOlson]

If you can find 'fire clay'--ideally containing about a 1:2 ratio of aluminium oxide and silicon dioxide--you can literally make insulating refractory bricks to build your reburn chamber out of for free.

[@lii1Il]

@@KeithOlson I need to do this. Ty

[@KeithOlson]

@@lii1Il You are most welcome. /bows

[@gavinddd2070]

You just defended your use of glass as the primary with your temperature argument. Glass doesn't start to melt well beyond the burning point of anything a rocket stove can produce. Question: Would adding a small turning vane at the base improve the rate of combustion with improved gas mix and vortex generation?

[@TrickyDickyP]

Rob, as an air control for the Rocket stove, add a flap or damper on the air inlet tube and extend the tube for the fuel (so you dont keep loading) and put a flap or door on that so the combustion air is sucked in from the front, this will be fully controllable after the stove gets up to temp. Try it and see what happens.. it is all about the air...! All the best.

[@TrickyDickyP]

@@kensmith5694 yes I Agree 👍😊

[@williambianchi2006]

I think cardboard fire logs could be made using a shop press and bailing wire, and without soaking in water, blending, and pressing in molds. Where I live, getting free cardboard is fairly easy, and I like the idea of cost-free fuel for a rocket stove. There are large machines in a lot of stores like Walmart that compress scrap cardboard into large bails. I think the same thing can be done on a smaller scale by cutting cardboard into strips, stacking those strips in a shop press, then compressing and securing them with bailing wire. That should give a fairly dense "log" to burn that would last a good while during the burn. Could even accidently on purpose spill some WMO or used veggie oil on the logs for added heat and longevity. Cheapest shop press I found was at Harbor Freight for $135.00 or so. I already have an electric saw to cut the cardboard. Haven't seen anyone do it this way, but it seems like it should work.

[@smartliketruck]

Hello Robert, the steel rockets you've been building may be fine for making a cooker in your garden but there are some things you need to consider when plumbing them indoors. If you add a chimney and/or insulate the secondary burn area you can increase the draft which in turn will increase the efficiency and temperature of the burn, this can quickly get to temperatures where the steel will corrode and spall. A complete internal collapse of internal structure is not entirely uncommon in less than 1 full heating season even with pretty heavy steel construction. If you add systems to harvest more heat downstream of the burn chamber and don't have a complete burn of gassified wood you are creating condensation point for creosotes and a chimney fire risk or collection of CO and oxygen mixture which can set off with enough force to blow the system apart. I hope you can beg, borrow or steal an exhaust analyzer like a Testo so you can assess this yourself.

[@ThinkingandTinkering]

the temperature is a function of the chemistry mate not of construction - that is reactions happen at a fixed temperature. Heat retention is a function of construction - so heat will continue to build in an area until the rate at which it dissipates matches the rate at which it is generated - if you insulate the dissipation will be slow, equally if you burn quickly the build up will be fast - see where I am going with this? That's why you can make a rocket stove from a bean can and why every stove is not a forge

[@smartliketruck]

@@ThinkingandTinkering Reactions happen at a fixed temperature when at a fixed ratio of reactants. If you increase the draft, you increase the draw of oxygen and increase the temperature of the burn. It is relatively easy to add 8 feet of pipe to your rocket and see how much hotter the secondary burn area gets.

[@DFPercush]

An exhaust analyzer would be cool to see, just out of curiosity. At least an O2 sensor. You can get a cheap automotive O2 sensor on Amazon for about $20 US, and monitor with a volt meter in the millivolt range. Lower voltage = more O2 I believe.

[@justinw1765]

Agreed, in a well designed and insulated rocket stove, if you use steel or regular, cheap, soda glass, these need to be protected with insulated cob (or something similar). Then these former materials can provide the structure for a longer time, while the clay (which is very heat tolerant) can take the brunt of the heat. Just by protecting steel from burning oxygen, really helps to preserve it. Soda glass doesn't oxidize, but of course has a lower melting temp, but more importantly, it doesn't handle expansion to contraction and back and forth very well. A combo of thermal mass and insulation helps to regulate those cycles (slows them down) so that it can last a lot longer over time and use.

[@aramraeymakers1856]

Amazing video on the topic!!

[@ThinkingandTinkering]

Glad you think so!

[@ChristieNel]

May I suggest a design that burns as hot as possible and uses replaceable fire bricks to contain the heat before diluting it with cold air before it is used or goes up the chimney? By controlling the mix ratio, you can adjust the temperature instantaneously.

[@lagunafishing]

I'm experimenting with some fused glass refractory material which seems to wick quite well, but it's a fine powder and splutters and pops when it starts to get hot so I suspect its a bit damp. I'll dry it out over an open flame and give it another go or I might add some water glass to it as a binder and fire it to make a ceramic.

[@emel60]

There are plenty of minerals you can use to create refractory materials, each with a benefit and a drawback. Whichever one are you using?

[@Moist_yet_Crispy]

What do you think about doing a series on home made lab glassware for chemestry and expirments? I feel as thought it would be useful to many students out there that can't afford the premium stuff and are only doing some of the basic exercises. Just been doing some self study in this area lately and have been collecting jars for some time for this purpose. I know you'd be an amazing practical chemistry teacher for noobs like me. Much love from the states

[@nixonsmateruby1]

My home is from the 1930s in Northern England and it has 6 air bricks, and as seen in your video about the Roman room heaters, I now need to find a way to get hit air in those bricks because it just blast's cold air through my wall sockets.

[@justtinkering6713]

EXCELLENT ! !

[@ThinkingandTinkering]

wow - cheers mate

[@Xero1of1]

I'm curious... if you're looking to make a rocket stove for winter heating... what if you capped the tube inside the building, then on top of the cap, you install another tube to exhaust outside and then you bend a bunch of copper tubes to go from the capped section to the exhaust section? Would you get more heat out of it? I think copper is a bit better at radiating heat than iron or steel... Put a small fan behind the tubes to help pull the heat off of the tubes and into the air... I dunno... thoughts?

[@groovygrannysbicycle]

I wonder if you could come up with an idea for a simple 'flu box' that one can sit atop a standard commercial gas heater that catches the bad smell that the burning of gas emits and lead it through a flu to the outside but not without first extracting as much heat as possible.

[@modelnutty6503]

yes about the mass, good rocket stove mass heaters radiate heat now from the barrel section, then the exhaust is directed through the mass to warm it up for slow radiating. it does take a lot more space to make the mass, but once warmed it may only take 2-3 small fires a day to keep a place warm. a chimney over a kerosene heater, that collected+pushed heat through a mass could work similarly, bright white flame is pretty efficient, same burn as a decent kerosene oil lamp gives but using a much smaller wick.

[@ThinkingandTinkering]

that's jus a hybrid device mate and so it behaves like a hybrid a bit of one and a bit of the other

[@shanealexander9952]

Using a lot less wood to whatever end is something. Personally, I want to make a turbine Stirling engine based on hurricane forces and a jet engine turbine. Good luck you say, but I'd need a miracle!

[@Ian8008]

Good video - as usual! Thought your description of the best use of the mass heater was poor though. Hear this - they normally have a more extensive chimney system inside the room - properly done they look to have a cool stack outside the house (virtually all heat left inside) and zero smoke (all fuel burnt). Now - regards the mass part. They're mostly set up in northern climes with long cold winters (Russia, Alaska etc.). So you're heating the house for months on end - continuously - day and night, to a varying degree - but always somewhat. Feeding the fire all the time is a pain - especially at night - so the idea of the mass is you run a furious fire 3/4 times a day (it goes out in-between) but it's evened out to a fairly continuous room temperature is the main idea of the mass. They use around a third to a half the amount of wood of an ordinary fire too - which save much work/money. So it's not so much a set up for Kent or Cornwall - perhaps Scotland.

[@jamesross1003]

Nice instructive video! Something to ponder over. I have been working on a design to further improve cooking vessel efficiency. Patent is the plan, though provisional is on hold for government usage right now(ie... military would be my guess for field cooking). Probably will not get the full patent within my lifetime. Since I can get no benefit from it and it has no benefit for other than cooking. I will share the basics here. Just take a cone shaped cowl(must be a metal that can handle a lot of heat) larger in diameter than the cooking vessel that is open at the bottom and is slightly shorter than the vessel. Hence, top is wider than the bottom. Attach a heavier rim(rim must be of a heavier metal than the vessel) to the cowl to then attach that to the vessel. A short metal fin attached to the rim pointing down inside the cowl to direct airflow back down to the bottom of the vessel(roughly center). The idea is that hot air will rise and be constrained up the entirety of the vessel exterior. The fin pushes the air back down in the center space. The inward cupping of the cowl bottom recirculates the hot air inside of the inner sides of the cowl. Basically gives the vessel a hot air coat that circulates around the vessel trapping heat that would otherwise be lost. In doing so the heavy rim and cowl itself will be heated and transfer more heat to vessel. Less heat losses and more efficient that way. Where efficiency is concerned it most times pays to consider working both sides of a problem from not just gains but also cutting losses. Keep the videos coming Rob! I really appreciate them, thanks!

[@jamesross1003]

This is different than Withange's patent in that the fin recirculates the heat again(a third time internally and again externally to the cowl). Also the heavy rim drops losses of heat. And with the shape being cone shaped with the inner fins it better baffles the heated air. Those differences make a big difference in efficiency. Cheers all!

[@CairnOfDunnCroftPermaculture]

Concerning rocket mass heaters, it's incorrect to say you don't feel the heat for several hours. That's true of the mass component, but the rocket core runs inside a radiant bell. And that radiant bell gives off huge amounts of instant heat. The mass then absorbs most of the remaining heat, and releases it over days. The mass extracts more heat from the fuel, essentially bonus heat. This effect absolutely does make it more efficient, and absolutely does get more usable heat from the fuel.

[@ThinkingandTinkering]

fair enough mate - cheers

[@cuboloudspeakers]

From my understanding, to give the stove the maximum live span, special fire bricks that can withstand temperatures up to 1700 degrees Celsius can be used. Based on aluminium oxide it will last longer than steel at the generated temperatures, these are readily available and do not cost much either. I would argue that the rocket mass heater shown at 8:28 is better in a way. It has a bell with the same function as the rocket stove shown a few seconds later. The second stove goes straight to the chimney after the bell, while not all energy has been extracted from the hot gasses. The first one extracts more energy from the gases by guiding it through a thermal mass (disguised as a coach) after the bell, before going into the chminey. So while they both have the same combustion efficiency and thus produce the same energy, the rocket mass heater extracts more energy from the gasses before releasing it into the chimney. With regards to energy efficiency it's better than the second stove, at the cost of added weight, bulk and complexity. Just my 2 cents ;)

[@ThinkingandTinkering]

fair points mate - I am more than happy to agree to disagree lol - though it does seem a bit unfair to compare apples and oranges - how do you think a mass heater would perform if it was just connected to the chimney and not the bench?

[@johndough8115]

@@ThinkingandTinkering It should be obvious, so its baffling that you do not see why. With the 8:28 design, the barrel releases the majority of the heat into the room.. quickly and efficiently. The remaining exhaust heat that escapes the barrel transfer stage... gets pumped into the Bench, to be absorbed by that huge thermal mass... before exiting the house, in a vertical chimney. The thermal mass captures virtually ALL of the remaining heat from the heater.. and releases it slowly, throughout the entire day. Unlike fully instant heat, which most of it gets quickly lost to the ceiling... rather than on the level where Humans exist. Also, Since you can not 100% guarantee that a burn will be 100%... especially at the start of the fire.. you cant just burn a rocket stove in a house. You need a chimney that exits the building. And if you are directly dumping super hot air right out of the chimney... rather than recovering it into a thermal mass... then essentially, you are wasting it. According to reports Ive heard... People with properly build rocket mass stoves, like the 8:28 design... went from using 4 chords of wood... to 1 chord of wood, for their winters burn period. Thats a huge difference in efficiency, and effective Heating.

[@justtinkering6713]

I just found a channel that has a " No welding no casting DIY rocket stove" the stove is made from "Vermiculite board" and has a double vortex. You might want to look at that. I was grumpy because the steel for making the stove was costing more than I liked and found this. He has a follow up video " Make it roar rocket stove upgrades".

[@ThinkingandTinkering]

I'll look into it mate - cheers

[@davidbarnes241]

Well explained and perhaps it’s just as well to create a hybrid version that one can adapt for various scenarios. This could easily be achieved by adding a sleeve of insulation in the form of welding mats, that could easily be removed. Likewise, a sleeve of old storage heater bricks that could easily be added and removed depending on the circumstances. Thanks for the inspiration 👍

[@ThinkingandTinkering]

I think so mate - I. like that idea

[@totherarf]

A note of warning (yes I used to install them) Some of the older units contain Asbestos! It is in the form of woolly insulation contained in a flat pack. There is no safe way to handle this short of a full decontamination unit specialised suits, masks and specialist disposal! Of course when we did it it was just thrown in a bin bag although they did upgrade to a double bag that was red back in the 90's! The bricks can handle quite high temp (mid red glow) but don't ask me how I know that!

[@davidbarnes241]

Thanks for the nod👍

[@davidbarnes241]

Thanks for the nod👍

[@justinw1765]

Yep, I already plan on incorporating this (general concept) into my design (i.e. off and on insulation). Along with lighter-weight thermal mass i.e. compressed talc in metal buckets (far better than sand). A hot water tank would be even better, but that is more costly and faffy. Water has a ridiculous (compared to most common substances) heat capacity. Makes soapstone look like a chump.

[@RichardHoganVlogs]

You should check out the batch box vortex rocket stoves, theyre a hybrid between a normal stove and a rocket, very cool!

[@ThinkingandTinkering]

they sound cool I will check it out

[@ThinkingandTinkering]

yep went and looked - got it and it is cool! gave me an idea! cheers mate

[@RichardHoganVlogs]

​@@ThinkingandTinkering look forward to seeing what crazy contraption you come up with!

[@inkhole]

Hello Robert. I've been enjoying working through your very educational vids so thank you for taking the time to create and upload them. I've left a message before to see if it is possible to adapt and expand little camping stoves into heaters e.g. the Trangia, or more interestingly, a 'woodgas' camping stove? What are your thoughts?

[@ThinkingandTinkering]

oh sorry mate I did read that and was going to do a video for you - the simple answer is yes - and it's not that difficult I will try and do it tomorrow - cheers

[@NM-wd7kx]

I recommend also looking into radiant mantles for tilley lamps for more ideas

[@inkhole]

@@NM-wd7kx Thank you. Funny, I've LITERALLY just lit my brand new Feuer Hand lantern and was surprised at the heat coming from it. I then thought of Roberts aluminium reflector and cake tin set up to make things even better. Thanks again for the info. I'll certainly look into it.

[@inkhole]

@@ThinkingandTinkering That would be great -thank you!

[@RalfyCustoms]

I'll second that, love my alcohol stoves but they must be THE most inefficient lol

[@johnillemann8012]

Hay, i am new to this channel and did not really know where to write a question to you, and sorry for my spelling! For some time, i wanted to make electricity from fire. At the top of a rocket stove, there is a lot of "wind" power. I have played around with Thermoelectric Peltier Element, but it is not that good! steam is not an option, where i want to use it. Is it possible to combine those to, your wind generator and the rocket stow? my problem is the heat at the top. it will make the coils, magnets and Berrings to hot, even when i put Berrings outside the chimney, the fan inside gets so hot, it takes the heat out to the coil and magnets outside! can it be solved or should i just give up the idea?

[@johnjrgensen701]

Actually a mass stove also give instant heat. Usually it has a glass door and this will give instant heat...

[@bk7278]

In my opinion after having tried and built a large mass heater and being very disappointed With the amount of heat that was coming off the mass I feel the best use would be to use the rocket stove to heat water and then heat a radiant slab perhaps but the best thing is to just get the room hot and then shut the thing down you’re much better off spending your time sealing up your home and insulating then you are screwing around with a mass that just ends up looking ugly

[@ThinkingandTinkering]

yeah - I agree heat the room fast and stop it leaking heat is what I would do

[@hippie-io7225]

@@ThinkingandTinkering Same approach to using solar: Remove as many electrical inefficiencies as possible, then plan your solar system.

[@TheKlink]

i like to call it a harnessed chimney fire.

[@johnnorris1983]

Robert. Love the Tardis on the shelf behind you.. Have you any experiments on time you can kick us off with?

[@RalfyCustoms]

Absolutely wonderful Rob, I honestly can't think of a good reason not to fit a rocket stove, instead of an open fire or even regular wood burner, that secondary combustion is a no brainer

[@ThinkingandTinkering]

cheers mate

[@chrissavill8713]

Some of the better wood burners do have a secondary burn chamber incorporated into the design.

[@metamorphicorder]

Well mass heaters also do something else, which explains why we still see people making videos about the plant pot/tea light heaters. It traps the heat as a certain level in the room. So in the tea light heater, build a tea light plant pot heater and next to it put a single tea light. Both tea lights put out the same ammount of heat. But the one by itself puts all its heat up straight away. Up and typically above peoples heads and out of their line of senses. The cant feel it and since heat rises, it stays there warming up the ceiling. The plant pot gives a visua focus and as you said lengthens the time over which the heat is released, but it puts it where it can be sensed. They make nice hand warmers but not much more. If someone wants to make a really good plant pot heater for a small space then get you one plant pot. Put a small piece of screen or a small broken piece of plant pot on the drainage hole and then fill the pot with plain bargain basement unfooled around with kitty litter, or vermiculite, and set up bricks or pavers such that they will hold the pot off the ground and hold it stable so it doesnt fall over. Get you some sterno heaters or chafing dish heaters and use two or three of them to heat the pot and the litter. This will also heat the bricks or the pavers but less so. This will put out some residual heat immediately, near the device, but like he said you are just charging a heat battery. Once its hot, a small electric fan will help it heat more air more quickly buy blowing air over it. You can get this quite hot as chafing dish heaters can last 4 to 6 hours or more depending on size and type. So maybe set up something to keep people from bumping into it and burning themselves on it.

[@Vibe77Guy]

A Question Of Balance.... Ah yes, wonderful Moody Blues album. :)

[@ThinkingandTinkering]

is it? awesome lol

[@cindypost8364]

Could you use an open flame gas heater with cooking oil with some adjustments

[@AcvaristulLenes]

Hi Robert, This video inspired me to formulate a challenge for you. Currently there are 2 types of stoves used in bikepacking: propane and alcohol stoves. Alcohol is not as energy dense and can be dangerous in case of a spill near the fire. But the stoves (see DIY alcohol stove) are very light (20 g?) and small, thus portable on long journeys. Fuel can be carried in different size and shape bottles. Propane needs a certain volume and it's harder to check amount left in the bottle. Access is also limited to some specialized shops that one can find or not in his/her way. Advantage: it's instant, no spilling, it's energy dense. Now, my question: Can you come up with a different type of small, easy to carry and to assemble stove design that uses some other fuel that might be cheaper and easy to find, with acceptable energy density? My next year's plan is pointing to Greece where I can find Lidl supermarkets. Stove will be used to cook food, not just tea. Trip will take 2-4 weeks, so we're talking about a lot of cooking. Thank you!

[@ObamaoZedong]

Check out tin can wood gasifier stoves. They're light enough for bikepacking.

[@AcvaristulLenes]

In the meantime I made one for myself. It's a very cool device but it consumes the fuel very fast. I'm thinking about trying out a mix of wood and used cooking oil. If it doesn't make a smoke column visible from the other side of the Atlantic, it'll be a winner choice.

[@duncanmit5307]

💜💜💜💜👍👍👍👍 clever stuff👍👍👍👍

[@ThinkingandTinkering]

cheers mate

[@ElenaHaskins]

*Wish* I had found your channel years ago (sigh...)

[@TheEmbeddedHobbyist]

Problem with storage heaters is you have to know what the following day will be like, which I found was an issue so great that they had to go (I never got it right). Gas central heating replaced them as soon as I could afford it. Cold turn it on, hot turn it down 🙂 is there a design which has an ash pan?

[@salimufari]

Early on you talk about the heat going into the bottom of the pan or pot but missed one of the key points of the rocket style stoves. The gasses, soot, creosote & solids a fire pushes into the space or out the chimney. Importantly in developing parts where these were invented for those gasses were killing the folks who had to cook indoors slowly by causing cancers, black lung & in extreme cases CO2 poisoning. The more complete burn reduced these compounds dramatically. 8:00 The catch here is the barrel style of mass heaters. The quick radiant heat comes off the barrel top & sides but just after the exhaust you can push the cooling gasses into a bell or mass. This stretches out the warming time.

[@ThinkingandTinkering]

it's not a catch mate - if you build a hybrid device you get hybrid behaviour

[@mcdls5]

Okay folks. Here's a twist. What about recommendations for a rocket stove for a maple syrup evaporator? My big question at this stage is wondering if I should put the rocket stove in front of the evaporator and have it exhaust under the pans or is some other configuration appropriate? One thing to keep in mind is that you want as fast of a boil as you can get. Slow heating isn't very useful as you're trying to keep the sap boiling and the more vigorous the boil the more efficient it seems to be.

[@_MKE]

I would use a "Liberator" style rocket stove. People make them with the J stove thing he's showing here (often with an auto feed section extending up and away from the firebox), with an insulating chimney, inside of an upside down 60 gallon steel barrel. The hottest part is sitting on top of that 60gallon drum. But you can also gain a huge amount of energy from the horizontal exhaust piping before it leaves the building. The efficiency difference isn't in the burn because they both burn nearly identical. The gigantic efficiency gain from the style with the 60gal drum is in capturing the heat from the exhaust before it leaves the building, and in dumping that heat down low so that it warms the floor and rises upwards through the building. It's important to have a hot firebox and initial chimney section to allow for complete and steady combustion, however for best heating efficiency you then want to steal as much of that warmth as possible without killing your chimney draft. The 60gallon rocket stove with the horizontal exhaust that comes out low allows for the best of both worlds. It really is far superior in every way.

[@Flashahol]

There never is a best solution for all situations. Anything designed to do 2 things or more never does any of those things very well. Think using a helicopter search light to change a car tire at night. Blinding yourself extravagantly is not useful for that application. Extra physics points (for the cool geeks): You made me realize that a mass heater simply slows down the heat like a Bose-Einstein condensate slows down light and releases it slowly. Heat IS infra-red light, so man has been slowing down light since before the measurement of the "constant" speed of light! A-HA!

[@toml.8210]

I think of the rocket stove as kind of mini fireplace. There is the firebox at the bottom, and a tall chimney.

[@mrmcclung]

My understanding is if a rocket stove is shaped correctly it will burn/reburn the flammable smoke, gaining efficiency & heat..(commonly called wood gas, that is lost in the normal process)

[@Adrian-kj3uc]

have you ever tried putting a heat exchanger on or even just a water jacket so you can heat water with excess radian heat?

[@mcbarberblue]

Brilliant as normal

[@ThinkingandTinkering]

cheers mate

[@a3b36a04]

Having a lot of thermal mass like the size of a house means you have more control over the temperature inside. Like not having to burn to 40 degrees in the evening to still have above 15 in the morning. Less thermal gradient = less heat loss.

[@freydablack9027]

Thank you for making the concepts inherent in the "rocket stove" much simpler to understand. There are one or two points you make, however, that do not seem consistent. first, you say that the mass heater does not provide more efficiency, it just shifts the time frame of receiving the heat. Do you mean that in comparison only to a rocket stove or any wood stove, such as a cast-iron airtight stove. Isn't there loss of efficiency if there is no mass to absorb all the heat produced through a long run of pipe through a thermal mass ? At a hot enough burn to consume all the gases, most of the heat will be lost up the chimney since conduction and convection are insufficient to move all the heat produced out through the walls of the stove. The other point you make, about the rate of burn not having any effect on the total amount of energy produced, similarly seems to contradict what you explained at the beginning about the stages of wood burning. When lowering the rate of burn, one must reduce the flow of air into the stove (again, I am referring to an airtight stove). At that slower rate of burn, the gases given off cannot burn and escape up the chimney, thus reducing the total amount of energy captured by combustion (and releasing air pollution). Only a faster/hotter fire can burn those gases completely and thus gain all the energy from the fuel. If I am missing something, please explain where I am mistaken. I am certain you know a lot more about this subject than I do. Thank you !

[@azlandpilotcar4450]

Good one. I always thought the early experiments resembled an Indian tandoor stove, even older than the Roman hypercaust.

[@ThinkingandTinkering]

nice one mate - I can see that

[@Liam....]

I want you to go back to your water jacket design and try and make it more effcient, I like the idea of being able to have the fire and gases burning outside but transfering the heat into a central heating system or something like that inside the house, most modern houses dont have a chimney.

[@ThinkingandTinkering]

Cool idea!

[@danielfeyerabend904]

You can experiment with venting the hot gasses through a normal firetube hot water heater. You may find one that was scrapped due to a bad burner. The problems are keeping the firetube from getting chocked up with ash or creosote, keeping the burn of the stove from being too long and overheating the tank or system, and building a rack strong enough to handle the 40+ gallon water tank. Getting the flames hot enough to burn all the gasses is very important. Having a controllable airflow and shutoff is next.

[@chaosopher23]

I wonder if one can be built with both heater and forge in mind? Turn it into a forge with the opening of an air valve or something...

[@doggymamadrama5881]

I've seen cinderblock rocket stoves will those work as well as store bought?

[@ThinkingandTinkering]

I honestly don't know

[@doggymamadrama5881]

@@ThinkingandTinkering I'll have to check into it. Thanks for your videos

[@superrodder2002]

I've been thinking about putting a wood stove in my shop. I also have lots of used engine oil from the cars I work on. I've been thinking about combining the mass rocket stove idea with an oil burner to heat the shop and get rid of waste. Any input about burning oil in a rocket stove would be appreciated.

[@l0gic23]

Recommend recycling the oil. Whatever goes up will come back down and its vest to keep that out of your air and ground water.

[@superrodder2002]

@@l0gic23 recycle it into what?. I've heard that it is sold as bulk fuel oil to run large ships to help cut their costs. If they can burn it, so can I.

[@NoToPCBS]

Get the best of both. A rocket mass heater with a contraflow drum. Instant heat from the drum and slow heat via the mass. I wouldn't built a J tube version i would go with a box mass heater with a contraflow as you can load it and forget it.

[@John-mc8sh]

I wonder if It makes sense to install a rocket stove, even a brick rocket stove, outside and make two holes in my wall, high and low or left or right, and make a 20cm metal pipe go out of the house with a computer fan past the flame and back into the house and let it heat up the air in a closed system and keep the fire and fumes outside for a house without a chimney. I wonder if I could easily plug those holes back up if it would not work well. Would love it to work well tho. Thanks for making these videos.

[@mrgrumps3062]

It will not be much fun standing out in the cold rain feeding it wood.

[@John-mc8sh]

@@mrgrumps3062 true, true….

[@emel60]

I have a question, Mr. Robert, Can you increase, by a homemade method, the radiation of the stove bodies? A building material, a paint job, something else ? Is it possible to achieve a significant difference? Thanks!

[@justinw1765]

Yes, you just spray paint it with a high temp paint of some kind. You could also put a layer of carbon on the outside, but that is far messier, potentially. The more shiny and/or polished the metal, the more it needs a treatment like this to absorb and transmit IR. Shiny and/or polished metals are particularly good reflectors of IR. Though there are significant differences between different materials. (Aluminum is one of the best all around, broad spectrum IR reflectors).

[@emel60]

@@justinw1765 thanks Justin, for your reply. I saw the terracotta pot trick Mr. Robert did- painting it with graphite. Now, that would be messy as hell, but I guess there are more stable paint solutions. I have sprayed my woodstove (see my YT channel) with a 800 C black matt paint. It holds relatively good so far, for two seasons. I've always wanted to know of there was any other brands pr solutions to further increase it? I guess I should eventually bolt to the wall aluminium plate, because of the high IR reflectivity property it has. That way the wall behind the stove would not steal heat as it does now.

[@adus123]

The rocket mass heater is more efficient because the flue gases cool in the flue pipes heating up the mass before exiting as the flue gases cool it shrinks causing a vacuum pulling in more air. There is less heat lost up the flue pipe to the outside.

[@simongross3122]

Great video again, thank you. Is it possible to capture the combustible gases to burn later or in a different device? Or is that just a silly idea?

[@ThinkingandTinkering]

yes it is - that's what a gasifier does

[@simongross3122]

@@ThinkingandTinkering Ta mate. I've got a lot to learn.

[@theimpatientbrewer]

Have a watch of the last season of Moonshiners. One of them made a still with a rocket stove and a wooden barrel. Very interesting idea.

[@ThinkingandTinkering]

for sure

[@matthewday7565]

I'm wondering if it would be helped by additional air ingestion, like the re-burn in a smokeless firepit

[@ThinkingandTinkering]

yeah - I think it would

[@lii1Il]

Yes if you hook up an air compressor, stand back and watch your forge turn into a pile of molten lava. Lol

[@3dpchiron709]

What if, inside the chimney there is a sort of bell shape (or upside down pan), maybe with holes in, to further catch/slow the gases as they rise? Placed at the point where the temperature is best for them to burn. Perhaps it would allow for shorter chimneys. [edit: or mesh baffles around the outside edge of the chimney, and a cyclone airflow to throw the unburned gasses out to the side and keep them in the hot zone longer - maybe even a catalysed mesh, like in your flameless heater vid).

[@ObamaoZedong]

You want to speed up the gasses not slow them down for efficiency.

[@TheIrishdriven]

mass heater does prevent heat loss like in a chimney large percentage of heat goes up flue

[@ThinkingandTinkering]

mate it doesn't - that's a function of chimney design - you can have a convoluted flue non mass that would do the same thing

[@danielroden9424]

how about the relatively recent improvement to Archimedes screw? instead of turning the screw you turn the housing and its *better*!

[@ThinkingandTinkering]

lolol- it sometimes feels like that

[@gordonwood3184]

Still confused Rob can't make my mind up wether to go for a log burner/ multi burner .Or go for a Gamera rocket stove from Bulgaria. What confusing me is would the rocket stove give out enough heat on its own 9kw . without turning it into a mass heater . Your advice would be very grateful . keep the video,s coming 👍👍

[@ThinkingandTinkering]

I don't know the Gamera mate, sorry

[@NM-wd7kx]

I'm not sure on the mechanisms required, but wouldn't the advantage of a mass heater be the capability to distribute less heat over a longer period of time? If I heat a bucket of sand with my rocket stove, then gently waft a draft over the hot sand to spread 'less heat' for more time?

[@ThinkingandTinkering]

sorry. mate I don't think it will spread less heat over more time for a given situation - it will spread at a fixed rate from hot to cold depending on the environment - isn't that thermodynamics? on thinking about it - in an absolute sense it will spread less heat as the mass will retain some of the heat

[@NM-wd7kx]

@@ThinkingandTinkering my wording is definitely bad here, you'd definitely need some form of insulation, heat pipe, airflow control, or other cheats/techniques to reduce the heat dissipation to a rate that you're happy with. I'm certainly interested in trying it

[@ThinkingandTinkering]

oh ok - I agree with that mate

[@you-know-who.]

Hey Rob seen as though you have got your rocket stoves to burn so clean... I was thinking 🤔 how about a heat reflector, like you see on the top of patio heaters???

[@you-know-who.]

@whasapp5637 Converse about you being a con artist? Leave this channel alone... everyone that watched this channel is educated enough not to fall for you scams

[@ThinkingandTinkering]

blocked and removed them mate

[@amwartwork]

ude think these ideas would be part of building regs but these days theres that flakey thing called insurance around.

[@felewoverthecoocoo2556]

Can you guess where these lyrics come from mr. smith?"... And all this science I don't understand It's just my job five days a week A rocket man A rocket man

[@ThinkingandTinkering]

would that be Elton John?

[@jesicasa3718]

I want to build a rocket stove under a galvanized "hot tub". Is it possible?

[@alexwild4350]

I'm not sure I heard the very last comment correctly. Did you say "Do ensure you like and subscribe" or was it "Do ensure you light and subscribe" ?

[@ThinkingandTinkering]

like

[@ceder4696]

💪