Musher deeds, thank you for this video!! I was able to take apart my 64 5. 5 Johnson outboard all the way down to the impeller because of it. Mine was a little bit easier. I was able to pull the driveshaft out of the lower unit and simply slide the impeller off the bottom. It's slid right out. I had to pay attention where the water pump aligned with the other rod for reassembly. My problem was that the key that holds the impeller to the rod fell out. I found it inside the water pump casing, slid it back into the hole in the driveshaft, just let the impeller over it and reassembled and it works fine now.
@Willah-wl3vm5 жыл бұрын
How did you set the fuel to air mixture? I took my carb off to clean the float which was sticking and I can’t seem to get the fuel to air ratio adjustments correct. Thanks!
@abrammcguire24594 жыл бұрын
Thanks for the video I have a 59 evinrude 5.5 Couldn't figure why it wouldn't spit water untill I seen the beginning of your video about the thermostat. So I pulled mine and it cools fine. Why is a thermostat necessary?
@neilyoungnut7 жыл бұрын
Musher Deeds... never laughed so hard in my life !! I`ve been where you were!!1 Love HATE relationship with these old outboards!! Jack
@cheechmachin013 жыл бұрын
I got almost the same motor evinrude 1962 5524r I believe. Is it 16to1 or 24 to1? Also I'm using it on a 12 ft v jon, is it enough to get it to plane? So far it opens up great after adjusting the mix speed on wot and on low speed sometimes it kinda kicks
@wmuhunter10 жыл бұрын
Have you had to replace the pull start yet? I have the same motor and I snapped the rope today.
@MusherDeeds10 жыл бұрын
No I haven't, mine hasn't broke. But we've been using it with success this duck season.
@davidmaj42595 жыл бұрын
I just had an issue with my starter but I cleaned it up and now its engaging. No rope issues yet.
@joshuanovotny24118 жыл бұрын
have the same motor and wont start any tips?
@POOHBEAR217010 жыл бұрын
Gotta love those old omc
@MusherDeeds10 жыл бұрын
I hated it at first, but it turned out to be pretty simple. excited to try her out. Thanks for the moment Pooh!
@aziggy252 Жыл бұрын
Poor design or not, these are good quality motors. But I understand your frustration 🙂
@ALVintageOutboards Жыл бұрын
Helps when your attitude doesn't suck before you start.
@aziggy252 Жыл бұрын
@@ALVintageOutboards For sure
@wmuhunter10 жыл бұрын
And did you ever put a thermostat in it?
@MusherDeeds10 жыл бұрын
no, I actually forgot all about the thermostat. I guess I should order one and put it in. whoops.
@wmuhunter10 жыл бұрын
Hahaha I pulled mine last night and will find put tonight if it spits water
@wmuhunter10 жыл бұрын
Have you cleaned the carb yet?
@MusherDeeds10 жыл бұрын
Matt LaFleur Yes, I did that when I first got it. It was very simple. I was careful not to get any carb cleaner on anything rubber so I wouldn't need a rebuild kit. But it ran great beforehand anyway. It really is an awesome motor, I wish they still make them.
@pwntagerz9 жыл бұрын
Musher Deeds - How'd you go about setting the HSN/LSN after you put it back together? The Seloc manual says something like 1-2 turns, but on mine it is closer to half a turn. I didn't spend a lot of time messing with it after I fired it up cause I thought it wasn't pumping enough water. Turns out it might be fine though, based on the last few seconds of your part 2
@pwntagerz9 жыл бұрын
I was watching this video because I thought I was going to need to change the impeller on my '62 5.5.... the water comes out the exhaust pretty much identically as yours at the end of your video, sort of spurting. I thought it was supposed to be a solid stream. Totally fine though huh?
@MusherDeeds9 жыл бұрын
pwntagerz yes, totally fine. if water stops coming out of the exhaust you've got problems. This motor was just stolen after a friend borrowed it and took it to Martha's Vineyard.
@jenessajohns9483 Жыл бұрын
I have the same engine. And same impeller issue. This video came in handy. Who the F&@k puts the shift disconnect UNDER the powerhead?? What a pain in the dick.
@ALVintageOutboards Жыл бұрын
Wow, what the!!??? 😂😂😂
@alexolivasolis8 жыл бұрын
thanks
@jimbuford41479 жыл бұрын
I am just one guy so who cares what I think, but what is wrong with the world? Can't anyone communicate intelligently now without using the F word?
@MusherDeeds9 жыл бұрын
Jim Buford Bad design = cursing allowance. Thanks for the comment!