1972 Evinrude 4hp lightwin outboard engine twin cylinder cold start

  Рет қаралды 41,287

origionaldz

origionaldz

Күн бұрын

Пікірлер: 41
@williamhiggenbottom
@williamhiggenbottom 4 жыл бұрын
Found one under the family tractor shed slapped it on the back of the boat backed into the pond and pulled five times she fired right up. Mind you it’s was under the shed for approx 25 plus years
@Fajah69
@Fajah69 3 жыл бұрын
I have the 3HP Johnson that is similar to this one. Smoothest thing ever.
@origionaldz
@origionaldz 12 жыл бұрын
$150 a fair price for a great running vintage outboard. I would feel confident on actually using it, in fact we may this weekend.
@outboardfixer
@outboardfixer 4 жыл бұрын
And we got a couple here.
@origionaldz
@origionaldz 12 жыл бұрын
It came with the gas tank, fuel hose and primer, original owners manual and some brand new lower unit oil.
@waydejenkins4964
@waydejenkins4964 Жыл бұрын
I have one. Full choke 1st pull, 1/2 choke 2nd pull starts EVERY TIME
@origionaldz
@origionaldz Жыл бұрын
They are really good outboards, will last forever with basic maintenance
@evinrudej
@evinrudej 3 жыл бұрын
Damn good price and looks like it’s been tuned up or just never really used
@rustynailz1687
@rustynailz1687 6 жыл бұрын
What's your slow and high speed adjustments on I've got the same year and model motor I'd like for it to rack off like that one!!???
@brentb7643
@brentb7643 3 жыл бұрын
I just got one for 200 cad today same issue yours has the clutch is loose how did ya fix it
@michaelmiley8552
@michaelmiley8552 Жыл бұрын
I just picked up the same motor! Is your still running well?
@origionaldz
@origionaldz Жыл бұрын
It was when I sold it years ago. I used it for awhile then upgraded to a bigger boat. Probably still running as these outboards are hard to kill.
@cliffpint4914
@cliffpint4914 11 жыл бұрын
throw a carb kit in it , also a impeller, both cheap parts, check leg oil to , milky = seals , also cheap
@roba9335
@roba9335 4 жыл бұрын
I have a 1973 Evinrude Yacht Twin 4 Hp 2cylinder. There is a knob on the front of the engine that adjusts "lean - rich". Anyone know what this supposed to be set on for starting, then normal trolling.
@origionaldz
@origionaldz 4 жыл бұрын
That knob only adjusts your fuel mixture off idle. You always want it more on the rich side. You have to fine tune it on the boat and under load.
@outboardfixer
@outboardfixer 7 жыл бұрын
Should have set mixture screws in front.......nothing wrong but that.
@cliffpint4914
@cliffpint4914 11 жыл бұрын
ps, very easy to do, fun little twin cylinders , maintain it and it will last a long time, pss never full throttle in a bucket = over-rev , and put some good oil in it like xd-50 also stay away from ethanol mixed gas e
@nikkibooth4905
@nikkibooth4905 10 жыл бұрын
I have a the same motor and my dad has adjusted all the mixtures, do u have some info on where they should be. I can get it to fire but wont run. New fuel pump and new plugs fitted, new fuel too.
@sailingdiscoverypassage
@sailingdiscoverypassage 9 жыл бұрын
Nikki Booth I have a similar question. I have a similar motor, and I'm currently trying to tune the carburetor. Could you let me know what the tuning turns are for the slow speed and high speed is? The only info I've found so far is a carburetor tuning for a 1957 Johnson 7 1/2 hp. They recommend 1 1/2 turns out for low, and 3/4 turns out for high. Would this be the same for the 1971 4hp? Thanks in advance!
@rustynailz1687
@rustynailz1687 6 жыл бұрын
I seated my top gently to the right then turned out one full turn and a half turn,on the bottom only about a half turn out only finger tighten the carb bolts with a half turn of a 7/16 wrench or it won't run period unless u put starter fluid init or straight gas which is very very bad
@justinpelletier5172
@justinpelletier5172 10 жыл бұрын
How much compression does your motor have? I have a near excellent looking motor but my compression is in the 45psi range. The motor will run throttle open but as soon as I try to idle it at a trolling speed it dies. I have so far invested in a impeller, fuel pump, head gasket, exhaust cover gasket, and cleaned the carb. Any ideas?
@alphadeltazero1659
@alphadeltazero1659 10 жыл бұрын
Change your fuel pump..
@justinpelletier5172
@justinpelletier5172 10 жыл бұрын
Thanks for the comment. I was able to get the motor running. I ended up doing a complete rebuild including coil and condensers and it runs like a dream. I think from the start it was coil or condenser. The bogging down was due to running on one cylinder. It was my first rebuild ever but i had my machinist neighbor help me out as far as what i should for when rebuilding.
@rustynailz1687
@rustynailz1687 6 жыл бұрын
Loosen your carburetor bolts the two nuts that go onto the studs only fingertighten them I replaced every piece of mine just to find out that's all it was
@thomastoups3451
@thomastoups3451 5 жыл бұрын
45 psi is too low. It should be at least over 65 or so. 75 to 90 is much better. These old motors are low compression. You aren't going to see 120 psi or higher like on modern motors.
@mikeyoung6347
@mikeyoung6347 4 жыл бұрын
Is the fuel mix 50:1 ?
@adamg.n.3170
@adamg.n.3170 10 ай бұрын
32:1
@danmontenegro592
@danmontenegro592 8 жыл бұрын
How do i tilt the propeller out of water?
@squat224
@squat224 8 жыл бұрын
Pull on the little lever under the downshaft, and then pull towards the bow of the boat on the motors cover. There's a lever/hook that catches on the adjustment pin, that's gotta be unhooked first.
@danmontenegro592
@danmontenegro592 8 жыл бұрын
+Squat251 Gaming thanks man, but can u make a vid or something. idk what any of that is
@squat224
@squat224 8 жыл бұрын
Danny Montenegro Sure, it was raining all day today, but I can make one tomorrow.
@danmontenegro592
@danmontenegro592 8 жыл бұрын
sweet man!! i really appreciate it, i just can't get how to do this lol
@myerchinizing
@myerchinizing 6 жыл бұрын
Anyone have a manual for this motor they're willing to part with? Just picked one up myself. Now the fun begins!
@origionaldz
@origionaldz 6 жыл бұрын
You can usually find the manual for these on ebay, thats where I got mine when I had it.
@myerchinizing
@myerchinizing 6 жыл бұрын
Yup, bought an online Seloc manual. So far so good. Parts in the mail. Should have it in the water this weekend!
@origionaldz
@origionaldz 6 жыл бұрын
Jason Myerchin nice good luck. These engines are usually bullet proof. Make sure you change the water impeller before you really use it.
@myerchinizing
@myerchinizing 6 жыл бұрын
Thanks for the advice. I'll def get one ordered. Can't wait to get it fired up. It's in really good shape. Hardly a chip in the paint. Couldn't have been used much. My turn to put it to work now.
@origionaldz
@origionaldz 6 жыл бұрын
Mine had awesome power and torque for a 4hp. I used mine on a lake for fishing. I'm on a river now so I need something with a little more HP because of the current.
1977 Evinrude 4 HP Starter Repair and Rewinding
27:57
Brandon's Garage
Рет қаралды 67 М.
Friends make memories together part 2  | Trà Đặng #short #bestfriend #bff #tiktok
00:18
風船をキャッチしろ!🎈 Balloon catch Challenges
00:57
はじめしゃちょー(hajime)
Рет қаралды 40 МЛН
PIZZA or CHICKEN // Left or Right Challenge
00:18
Hungry FAM
Рет қаралды 12 МЛН
The Singing Challenge #joker #Harriet Quinn
00:35
佐助与鸣人
Рет қаралды 25 МЛН
Evinrude 4hp TOP SPEED!  (Modified?!) 1970 lightwin.
3:34
1969 Evinrude 4hp YachTwin 2 cylinder 2-stroke
4:15
Outboard Madness
Рет қаралды 550
Pinpointing Problems On a Outboard Motor
14:36
ThatBoatGuy
Рет қаралды 1,2 МЛН
1972 Johnson 4hp
6:23
acatsnowman
Рет қаралды 10 М.
1977 Evinrude 4 HP Outboard Test Start
22:05
Brandon's Garage
Рет қаралды 54 М.
1972 evinrude 4hp
3:05
Skidoo elan73
Рет қаралды 469
Getting a Spark but your Outboard Motor will not Start?
10:03
Matthew Brenengen
Рет қаралды 177 М.
1980 Johnson/evinrude 4hp on a seago 2.6m inflatable boat
1:32
Tom Reeve
Рет қаралды 2,1 М.
Evinrude 4hp part 3. Impeller access
9:08
accordioncafe
Рет қаралды 43 М.
Friends make memories together part 2  | Trà Đặng #short #bestfriend #bff #tiktok
00:18