1994 to 1997 Chevy S 10 Front Grille and Bumper Replacement guide by Howstuffinmycarworks

[@colbysmith7724]

Dude I wish everyone's help videos was as smooth and to the point as yours! I'm doing swaps on my 94 s10 and this helped me alot!! Thanks

[@bernarda658]

Dang: You're so young. You look like a kid still in high school. Glad you showed this old geezer something. But I need to know how I can straighten out the bumper just enough to stop it from rubbing on the left tire to drive it to ABRA. Oh, thanks for the video.

[@pudding247]

Hey man, nice work. The guide is very easy to follow along with. I own a 1998 Chevy S-10 and I thought I'd point out the differences in-case someone owns a later model. Difference 1: The grill is not held in by any bolts, it is only held in by snap clips. Also, be extremely careful when taking the grill off, 20 year old plastic is fragile. Difference 2: You must gently pop out the turn signal from the grill. You only need to take off the lens (light cover?) of the turn signals. Disconnect them in the manner shown in the video. You do not need to touch the headlights. The way the 1998 bumper is bolted on is different from the 1997 model. There are two bolts underneath, located near the wheels (back corner on both ends of bumper). You must use a pivoting extension (I needed two) in order to remove the bolt. You must also (or at least I did) place a wrench on the square nut which is also on the bolt. The wrench pretty much holds itself in place and is only there to prevent the nut from turning. Under the hood of the truck (top of the bumper) there are 4 bolts. They are in a similar spot to the ones in the 1997 model except the 2 lower bolts are slightly harder to get at, use a pivoting extension (for your ratchet, of course). Other than that, it is a very similar process to the video above. Note: my 1998 S-10 is the sport side edition, I am unsure if the standard model has the same configuration.

[@Ambderp]

This helped , Thank you

[@gadasavideos8564]

Interesting. Didn't realize until that gen 2 was restyled in 98

[@curtisbundy432]

Saved me a lot time and my swap of the front end was easy after your video!

[@fumemanv]

Best S10 how to , ive seen,very straight,forward and to the point thank you for sharing..

[@floydjones7627]

Wow! You made it look super easy! Thank you for a perfect demonstration video! I will be changing mines this weekend. Thanks to your video, I will go into the project with a lot of confidence! Thanks again!

[@danielamezcua8007]

Ordered a billet grille for my Sonoma!! Thanks for the video man

[@JD-og9fv]

Nice video dude. Love how you kept the box under while installing just in case. Smart move. Keep up the good work

[@ombatexec]

Man, you are the best! I love my '97 S10 and you are helping me keep it straight. All I need now is your coordinates so I can add you to my will! :-). Thanks, Chris!

[@jeffmiller3499]

Great video man. I have a 99 so it seems a bit different & I'm super lost overall lol. but your video is very helpful!

[@SpringboroTea]

Excellent. You said it in a calm and easy to listen to manner. Thanks!

[@beardedtruck-a-holic3833]

the most help video out here . you made it look so easy tha k brother!

[@gretabridges3364]

Wow you made this look so easy. I'll be doing this tomorrow on mines. Thanks

[@C4props]

great video. this is going to help me replace mine. only down side is no list of required tools and I think thats an LS model which has a different bumper with chrome trim.

[@GlynRobinson]

hey Chris! great video!! Thanks

[@justinsmet]

Do you need the hood open to do it, my hood latch us stuck closed and tried pulling cable but doesnt to anything

[@jimmajr9224]

u da man. thank you for making this video. !

[@casasessi]

Do you know if 2002 blazer front end / hood will fit on my 2000 Chevy S10?

[@RetiredTony]

good job man...thanks for the video

[@nicolasptejeida5999]

Muchas gracias... Thank you very much....

[@danielamezcua8007]

Do i need to unhook the negative from the battery if I’m just replacing the front grill or should I be okay?

[@chaimyamin]

Appears to be helpful, and it is!

[@dvddmc]

how do you remove the lisens plate bracket on the front??

[@amanda_3697]

What exact tools did you use in the video ?

[@aww4954]

Well done sir.

[@thebakery3996]

All these positive comments but no likes or dislikes. Wtf?

[@stevendiffy768]

I have a broken bumper end cap. How do I remove it and replace it?

[@leeB0nes]

Very helpful, thanks!

[@robbiegonzalez1839]

Hello! Do you know what bolt size should I use for the rear bumper bracket? My rear bumper fell on the road and can't find the right size.... Thanks!

[@RavenKraken]

LMC truck has the bolts you need

[@turtlegaming3829]

Quick question for everyone on here, I drive a 2002 GMC Sonoma. I want a steel front bumper that’s made for the s10. I know that most parts between these trucks are interchangeable but is the bumper?

[@atlaseca]

need help jump start a suv with my chevy 97 s10 after the jump the truck started smokING from the left bottom corner around the battery..and won't turn back on

[@wdfgamingnetwork]

What size is the star bit bolts?

[@GetItDoneProjects]

Can't speak for any other year than my 1996, but the Torx (star) bit is a T50.

[@retiredrainbow2331]

were can i buy all the parts for the bumper

[@dannyfallahi1970]

Junk yard

[@Sounga74]

Can you show us how to do a 2001 chevy blazer LT

[@americanmilitiaman88]

should be about the same. slight differences. i have a 01 lt blazer with almost the same damage this has becuase these people decided that lights were not needed to drive at night

[@ilegendary1924]

Excelenteee

[@torowazup1]

👍🏼👍🏼👍🏼👍🏼👍🏼👌🏼😎

[@nathanmccutchen9315]

Buddy you did a great job but before you start all your kids tell us the tolls we need