How to Replace Timing Chain 96-99 GMC K1500 5.7L

Buy Now!
New Timing Chain Set from 1AAuto.com 1aau.to/ia/1ATBK00063
1A Auto shows you how to repair, install, fix, change or replace a broken, noisy, squeaky, worn or groaning timing chain belt tensioner. This video is applicable to the 96, 97, 98, 99 GMC K1500 5.7L
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oTE/1AXAA00013
• Complete Metric Socket Set 1aau.to/okE/1AXAA00043
• 2 Jaw Gear Puller
• 3 Jaw Gear Puller
• Harmonic Balancer Holding Tool
• Harmonic Balancer Puller 1aau.to/ok/1AEHB00094
• Adjustable Wrench
• Channel-Lock Pliers 1aau.to/oav/1AXAA00139
• 3/8 Inch Air Impact Gun
• 3/8 Inch Drive Ratchet 1aau.to/oJ8/1AXAA00015
• Torque Wrench 1aau.to/oox/1AXAA00044
• Anti-Freeze
• Brake Parts Cleaner
• Gasket Adhesive
• Paper Towels 1aau.to/oeQ/1AXSS00035
• Drain Pan 1aau.to/oec/1AXAA00320
• Funnel 1aau.to/obA/1AXAA00310
• Hammer 1aau.to/ogS/1AXAA00091
• Razor Blade / Gasket Scraper 1aau.to/oa2/1AXAA00280
For More Info visit us at 1aau.to/h/aAE/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@jameskelly2094]

On reinstall tighten the pulley center bolt 🔩 to 70 ft the balancer on the crankshaft moved from compression stroke mark. Is that okay in order to get 70 ft Torque on center bolt 🔩? I hope you can respond to my question... Thanks...

[@matthewclark7781]

All these videos are by far the best automotive tutorials on KZbin

[@camo_fisherman]

Great instructional video without the unnecessary talking. Straight and to the point! Love it!

[@Joeelectronicschematicsforauto]

your videos are absolutely amazing with photography and description I really think that you'll video should be made for students in vocational schools while learning automotive like Lincoln tech and other schools absolutely amazing you are what you do

[@jamessmejkal8803]

I agree, videos are great in a training situation. " A picture" is worth a million words. Back when I was in "Auto School" we found videos well worth the time.

[@jhanlon1903]

when you put the water pump on make sure you put rtv silicone for anti freeze on the threads, as the bolts go into the water jacket

[@esanzi41]

You deserve appreciation and praise. It is an excellent channel. I really benefited from it

[@esanzi41]

Thank you for this excellent channel. It deserves all the appreciation. Excellent practical explanation and wonderful photography. This defect is found in my car GMC 1996 Sierra 1500. Thank you.

[@gcaprice406]

Great video, just a couple of follow up notes: -There is a very good chance that you will have to remove the first 6-8 oil pan bolts to get the cover out. It is rare that the cover comes out without doing this, as it seals to the oil pan. -On the same subject, look at your oil pan gasket where it seals to the timing cover. A lot of these trucks have had their oil pan gasket replaced, and usually with a FelPro brand gasket. The FelPro gasket is one piece, and is quite thick where the oil pan seals to the timing cover. In this case, you would not want that massive bead of silicone in there. Just clean the one piece gasket very well with brake clean, and then put a decent sized spot of silicone on each corner of the timing cover where the oil pan lips seals to it. -I would strongly recommend using red Loctite or the special locking fastener the aftermarket offers to keep the 3 cam gear bolts tight. Not necessary, but why take the chance of them loosening up. -Use thread sealant or Teflon tape on all 4 water pump to block bolts, or they will leak. -Lastly, you might change the chain only to find that the engine runs rough/doesn’t start, or the computer sets a P1345 Cam/crank correlation code. This can happen if the vehicle was retimed at any point while the chain was loose. If so you will need the engine retimed with a scan tool. Great video though, and good luck with your repairs everyone.

[@1AAuto]

+gcaprice406 Thanks for checking us out! 1AAuto.com

[@waynemcaurthur8026]

Hey there, good comments. I can't find any good videos on how to do the timing correctly with a timing light. Specifically where the dam cable is for the auto timing to the ecu, that needs to be disconnected first. Any suggestions or links you have would be awesome. Thank you. 1997 K1500 5.7l vortec

[@jameslogue8394]

Nice step by step video! I'll be doing the same on my 96 Astro. 230K miles and not running to well per timing issues. I assume the chain must have some bad slack. Adding my 2 cents, I see you added a new water pump on the re-assembly. Loosening the bolts on the water pump pulley would probably been easier (for those who don't have an air ratchet or impact wrench) before taking off the serpentine belt. Also, the same for the crankshaft pulley as well. Cleaning the gasket residue around the water pump jackets and the timing chain on the block first would probably been easier before adding the new chain set. Other than that, awesome and most detailed video I've seen on youtube! Thanks!

[@1AAuto]

+James Logue Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/timing-chain-set/i/1atbk00063?KZbin&CTA+Comment&UeIe2Cgchs

[@veronicathebeautiful]

Well, I just wish... I COULD DO THE JOB MYSELF! Who can pay $2500 dlls for this Job. My truck 98 Chevy Tahoe needs to pass emmisions inspections, because the stupid engine light is on and has been on for years. AND DOES NO HARM TO ANYONE! MY TRUCK RUNS JUST FINE! What the hell!!!!

[@colesheperd1165]

Very good advise I was thinking same thing

[@Rolandrollins]

hell yea , mo fo's ... this vid was a life saver... im ordering from 1a now

[@1AAuto]

+Roland rollins Thank you for your order. If you would like to leave us a review on Google it would be greatly appreciated. Here is a link to our reviews section. Have a great day! goo.gl/i5JFNY

[@etceteraleatherworks1103]

Awesome video! Eagerly awaiting the oil pan gasket replacement video for this model of truck.

[@1AAuto]

+Etcetera Leatherworks We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com

[@allanbrogdon7453]

On removing the bolt on the crankshaft put a socket on bolt with a breaker bar against frame bump starter bolt comes loose it is threaded this way so it doesn't come loose while running.

[@blacktone1084]

U made this look so simple and easy

[@robertj.3682]

You guys are amazing!! Deeply appreciated

[@Marc48ify]

You should do one for a 5.3L silverado/Sierra that would be so awesome! I love your videos.

[@1AAuto]

+Marcus Blanco Thanks for watching. Have a great day!

[@EATSLEEPFARM]

I miss when this channel did actual repairs. Great video!!

[@1AAuto]

+It'syourboy LS Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@ntambidean3016]

so great guys !

[@philipeckstrom1254]

Check your torque specs! Timing cover is 6.75 ft-lbs not 18! (or 75 in-lbs). I figured that out after breaking off 2 screws in the block!

[@bigdaddy7913]

How did you fix? I had the same issue. I knew it seemed a lot tighter than they came off too.

[@kevinbaker7936]

Yeah I snapped 9ne of mine also. He also doesn't tell you that the oil pan gasket is one piece and you tear the part between the pan and timing cover when you pull it off. Now I gotta drop my oil pan to fix that. Mine is leaking right there.

[@adamjohnson286]

Thanks a ton for this video. I should tell you that I tried to buy the timing chain (or cover, I can't remember) from you and you are out of stock. Funny. I'm originally from Hopkinton. Keep the good videos coming.

[@McCracken_9]

Oil slinger or reluctor wheel for crank position sensor?

[@jsmith3019]

Oil slinger ? You mean the relucter wheel that keeps the timing for the computer.

[@Devo1987]

It may ! be for both

[@nicenonya3]

wish this was for the 4.3 L vortec,looks very close to it,but I've seen some that require the oil pan to drop out of the way!

[@jasongrappone345]

Would’ve been great to know that it may leak if you don’t drop the oil pan front! Used a ton of RTV and it was a PITA to get in and still leaks which now means I need to drop the oil pan AGAIN! To finally get it to stop leaking!

[@mistakrazeunomas6943]

🤦🏽‍♂️

[@kellismith4329]

I usually replace the balacer at this time also, when fixing the cover, install the balancer enough to centre itself in the seal, secure the timing cover bolts you can reach, then pull the damper off again to alpply final torque to timing chain cover - it is sometimes necessary to test the crank pos sensor clearance toshaft as the cover may be shifted slightly from centring seal to shaft. Spacers can be added to sensor to increase clearance.

[@mikes6916]

Guy cleaned the housing after putting the new chain on. Guess hes trying to grease the new chain with the old sludge. 😂

[@lisandromelendez9545]

Good teaching. I have to do that to my 96 Tahoe. It's running well, but there is a slight hesitation on the engine.

[@1AAuto]

+Lisandro Melendez Thanks for watching, hope this video helps you out. If any of our viewers needs to make this repair, we carry the new timing chain shown in this video on our website. Here is a link to them. We also offer free shipping. Hope this helps you out www.1aauto.com/timing-chain-set/i/1atbk00063?KZbin&CTA+Comment&UeIe2Cgchs

[@johncoulter1507]

Great job!

[@jimatkins2980]

Best damn informational video I've ever seen. Great job dude 😎

[@1AAuto]

+Jim Atkins Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@randybeard6040]

Very Good Video, Very Informative!!!

[@1AAuto]

+randy beard Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@Luisrod56]

GREAT video guys thanks alot

[@1AAuto]

+Luis rodriguez Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them: www.1aauto.com/timing-chain-set/i/1atbk00063?KZbin&CTA+Comment&UeIe2Cgchs

[@georgemarquez7850]

I looking for some help to how to change a timeing Cain on a 2000 Lincoln LS with a V8

[@biff314]

Good video, thank you. What was the torque on the three crank pulley bolts? What was identified as an oil slinger, is the crank sensor reluctor ring. Clean the timing cover gasket surface, and water pump gasket surface as soon as the timing chain and gears are removed or, prior to installing the timing chain/gears and timing cover. Makes it easier to access those surfaces without those items being installed.

[@1AAuto]

+biff314 Step 1.Removing the Fan Shroud 0:59 Unclip the wiring retainer from the fan shroud with a flat blade screwdriver Pull the wiring off the fan shroud and set it aside Remove the seven 10mm bolts from the fan shroud Lift the fan shroud up and out Step 2.Draining the Coolant 1:47 Twist off the radiator cap Have a drain pan ready Twist off the radiator drain plug Allow the coolant to drain Twist on the radiator drain plug Step 3.Removing the Fan Clutch 2:13 Attach an adjustable nut to the fan clutch nut Tap the wrench with a hammer to loosen the nut Attach a 3/8 inch drive ratchet to the serpentine belt tensioner Turn the tensioner as far clockwise as possible Tap the adjustable wrench with the hammer again Remove the ratchet and the adjustable wrench Spin off the fan clutch Step 4.Removing the Serpentine Belt 3:16 Familiarize yourself with the route of the serpentine belt Insert the 3/8 inch drive ratchet into the tensioner Turn the tensioner clockwise to loosen the belt Pull the belt off the alternator Release the tensioner Pull the belt off by hand Step 5.Removing the Water Pump 3:45 Press the clamp on the upper hose Twist the hose free Remove the hose Have a drain pan ready Loosen the clamp on the lower hose Wiggle the hose free Remove the four 14mm bolts from the water pump Pull the pump off Remove the last hose Remove the four 10mm bolts from the water pump pulley Remove the pulley Step 6.Removing the Crankshaft Pulley 5:51 Remove the three 14mm crank pulley bolts Remove the 16mm center bolt Remove the pulley Step 7.Removing the Harmonic Balancer 6:43 Reinstall the 16mm center bolt without the washer Insert the hardware from the puller kit into the bolt holes Run in the center bolt supplied from the puller kit Tighten the center bolt Slide the harmonic balancer off Remove the center bolt Step 8.Removing the Timing Cover 8:22 Disconnect the crank position sensor Remove the 8mm bolt from the sensor Remove the sensor Remove the eight 10mm bolts around the timing cover Remove the timing cover Step 9.Removing the Timing Chain 9:15 Remove the oil slinger Insert a socket as a spacer into the crank Rotate the crank until the timing marks on the gears line up so that both dots on the gears' teeth are lined up close to each other Hold the crank shaft with a 16mm socket and ratchet Remove the three 13mm cam sprocket bolts Remove the camshaft sprocket and timing chain Install the two or three jaw puller to the crank gear until the gear comes off Step 10.Installing the Timing Chain 13:06 Install the crank shaft gear with the dot facing you Tighten the bolt with an impact gun Insert a large socket or install tool and tap it to adjust the pulley into place Insert the 16mm crank bolt Insert the camshaft pulley and chain into place and around the crankshaft pulley Push the cam gear in Reinstall the three 13mm cam sprocket bolts Torque the cam sprocket bolts to 26 foot-pounds Reinstall the oil slinger with the high side facing in toward the crank gear Remove the crank bolt Step 11.Installing the Timing Cover 15:17 Wipe off any grease off of the timing cover and around the chain Scrape off any built-up gasket material with a razor Wipe off any dirt and debris with brake cleaner Apply oil safe gasket sealer to the bottom of the timing cover Press the bolts into the cover Press the cover into place Tighten the 10mm bolts Let the adhesive dry Torque the bolts to 18 foot-pounds Install the crank position sensor Tighten the 8mm screw to the sensor Connect the connector to the sensor Step 12.Installing the Harmonic Balancer 19:35 Install the installer tool into the crank shaft tightly Insert the harmonic balancer onto the crank Tap the balancer with a hammer Install the sleeve of the install tool Install the bearing Install the bolt and tighten the nut down until the balancer is bottomed out Remove the tool Step 13.Installing the Crankshaft Pulley 21:15 Insert the pulley into the engine Tighten the 14mm bolts to the pulley Tighten the 16mm center bolt and washer by hand Step 14.Installing the Water Pump 21:40 Tighten the four 10mm bolts to the pulley Clean the gasket surfaces with a razor blade Set the bolts into the pump Place the gasket on the pump Connect the inlet hose to the pump Insert the pump into place Tighten the hose clamp Tighten the 14mm bolts to the water pump Torque the bolts to 30 foot-pounds Reinstall the remaining hoses to the water pump Step 15.Installing the Serpentine Belt 23:23 Loop the belt around the crank pulley Bring it around the water pump Bring it under the power steering pulley Bring it around the A/C Pulley Bring it around the belt tensioner Bring it under the idler pulley Pull the tensioner clockwise with the 3/8 inch ratchet Pull the belt over the alternator Release the tensioner Torque the center crankshaft pulley bolt to 74 foot-pounds Step 16.Installing the Fan Clutch 24:33 Start the fan clutch nut onto the pulley by hand Attach an adjustable nut to the fan clutch nut Tap the wrench with a hammer to tighten the nut Step 17.Installing the Fan Shroud 24:48 Line up the fan shroud Fasten the seven 10mm bolts into the fan shroud Place the wiring on top of the fan shroud Clip the wiring to the fan shroud Step 18.Filling the Coolant 25:17 Add coolant to the coolant bottle using a funnel Twist on the coolant bottle cap Run the engine briefly Add coolant as necessary

[@abdalraheemalmasri703]

Great video

[@tommylopez8338]

Replace the ignition switch module! My truck had the same issue. GM was having ignition switch problem way back in the 90's as well. Replace the ignition switch and the crank shaft sensor.

[@1AAuto]

+tommy lopez Thanks for checking us out. 1aauto.com

[@camerojl]

Like your vid’s but I’d like to note that on TDC of the #1 compression stroke the cam reference mark is at the 12 o’clock position. Unconventional in my experience but everything starts with the engine set at the TDC of the compression stroke on #1 cylinder.

[@badboyr66]

Old video....solid video

[@BasicBenny]

thank you!

[@ez439]

Alittle work there huh👍

[@chrisallen3839]

Tried tightening the belt like this guy did on a 2001 gmc jimmy, pullies would still turn, finally broke down and got the actual tool at Advance auto, so much easier, ull need a 1 and 7/16 inch wrench and a tool that u take 2 bolts out of the pully behind the fan then instert the tool to hold that in place

[@andersonautohelp1563]

Or just hold the pulley with a pry bar instead of even stretching out a otherwise good serpentine belt.

[@andersonautohelp1563]

Also never pry on old hoses with pliers...use a pick and spray a little silicon. Will come right off easy

[@andersonautohelp1563]

Also when turing a engine by hand...remove your spark plugs this way your not fighting so much compression.

[@1AAuto]

+Anderson Auto Help Thanks for the feedback!

[@cCH3artlessCc]

FYI when you put the cover on it doesn't actually slide in like it looks like it does that's why you have to put so much rtv on. Found this out the hard way.

[@1AAuto]

+Tyler Elliott Thanks for the tip!

[@rickwolhoy2151]

Great video. Except for the part where he says torque the timing cover bolts to 18 ft. lbs. I just broke a bolt in my block. The correct torque is 106 inch pounds. Very frustrating.

[@kevinjunge2279]

I broke a timing cover bolt while torquing to 18 ft-lbs. Make sure to double check the torque specs for your vehicle. After doing my research I found the torque spec for my timing cover listed as 106 in-lbs or about 8 ft-lbs. I have a 99 K1500 Suburban

[@paulsears775]

+1. I also broke a bolt and had to drill it out. Chilton's recommends torquing to 100 inch pounds, or 8.3 foot pounds.

[@leilanichaplin7642]

How long did it take you to do a job like this?

[@trillrifaxegrindor4411]

you need to always use a measure of common sense when working on cars,trucks etc.a timing or valve cover or oil pan/trans pan isnt a structural or combustion sealing item so it will always be in low inch pound increments or tighten to tight plus an 1/8 to 1/4 turn

[@Devo1987]

Lock tight ? For timing cover bolt?

[@carolbellinger]

thank you, that was the best video I have EVER watched for doing this. I was told there is 2 differant timing chains for my 97 GMC Sierra 1500 truck, it;s got a 5.7 V8 motor. they told me They needed to know what timing chain it was. So I need to take it off to show them what one it is? Is this true?

[@charlierosene1117]

8 digit of the VIN assuming it is a 5.7 then: If the 8th digit is R then you have .280" Tooth Width Sprocket

[@ianwilds3139]

You are correct..there are two different types one being a roller chain with .280" width sprockets or the inverted tooth chain with .400" width..my '97 Vortec 350 VIN R has the latter.

[@randallw7437]

I noticed you didn't mess with the distributor, do I need to setine 180 out cause I changed my chain and distributor

[@pauljb1979]

When I took off the cover on the oil pan side there was a plastic seal that fell apart. Will just the gasket sealer work or do I need to replace that plastic front main seal part?

[@freebrady8789]

a little late but rule of thumb I've been taught I'd is a if you take a component that has a gasket replace it. The cover should be ok unless you notice a crack. Gasket sealer was place at the bottom to reinforce where oil will sit the most

[@brettneuman1960]

Do you need to remove the oil pan first

[@csarebel8657]

Would this be the same process for a 5.3 vortec? 99 Sierra Z71

[@allanbrogdon7453]

Don't they use gasket glue any more?Also silicone always shrinks later been many years in silicone better now i had bad luck with this trying to use it as a gasket replacement.

[@lightningsurvivor1432]

How do i know when it bottoms out. Will just turning? I dont want to ruin anythin as it gets tighter and tighter

[@robertwilson4400]

would this video and steps also apply to 88-94 Silverado

[@b_wilk98]

Was this Truck throwing a p1345 code before the timing chain and sprockets were replaced?

[@TateReggie]

Thanks!

[@richodd2292]

i replaced mine, it dosnt leak at idle or reving the gas, but on the road i have a leak, i used a whole tube of sealer, whats the issue? clean it and apply more sealer to see if it stops?

[@bobduncan9060]

TDC compression stroke number 1 cylinder : both cam and crank marks are at 12 o'clock position.

[@johnathanlivings8540]

Is this correct? Sure seems like it! Because I'm at this very point and my rotor is at the #1 cylinder when both are pointing at 12 o'clock position!

[@wayne8498]

@@johnathanlivings8540 yes it is correct. When dots are at 12 and 6, (dot-to-dot) that is actually number 6 top dead center. Edelbrock techline confirmed this for me and it was correct when I started the engine.

[@jodybuell9710]

How do you replace the keyway on the crankshaft in a 97 GMC suburban 5.7 leater

[@juniorcharter639]

I'm putting the head's and intake&all the accessories off the off my 95 throttle body on the block of my 97 Vortec do I need the oil Slinger

[@juancupen1162]

I put the change and its feell lose in both sides feel the same like the old one i buy this truck a week ago and i try to replace the timing change and i dont know if the rigth part

[@christieturner5567]

Could you please do a timing chain replacement for a 2008 chevy equinox sport 3.6 l v6 soon?

[@1AAuto]

+Christie Turner Thank you for checking us out. We will keep this in mind for a future video upload. 1aauto.com

[@johnhandcock3242]

What is a holder? How do you keep that wheel from turning?

[@victorreyes2135]

Remember ,I did this job on my girlfriends truck , ..4hours later she attempted to start the engine, and it popped, The look on her face was priceless 😂😂 😂🤣 🤣...

[@1AAuto]

+Mr Vic Thanks for checking us out! 1AAuto.com

[@xhambonegaming2694]

One time use on timing cover for 6.5?

[@johngouker3887]

my 4.3 has a geared ballance shaft , how are the dot's lining up

[@Djevan41598]

I never knew you had to replace timing chains

[@1AAuto]

+djevan 41598 Thanks for the feedback!

[@scottbox1342]

When you turn your crankshaft this way do you ever risk breaking your crank pulley screw that you used?

[@1AAuto]

+Scott Box Not typically, as long as you follow the directions in this video you shouldn't have any problems! 1aauto.com

[@TheSweden740]

Hello. I used your torque specs on my timing cover which you stated in video 18ft pounds and I broke 2 bolts off instead the block. The correct torque is 6.5 ft pounds. Not very happy. I will from now on just look up torque specs

[@JJ-tv2pc]

Is it better to heat crank sprocket for install or using the tool shown?

[@jamessmejkal8803]

NO, it does not slide on that tight, just clean the crank nose a little with sandpaper or cloth and it will slide on.

[@togodbetheglory9725]

How long it takes to do this job?

[@davidsummers4558]

Timing cover torque specs say 7ft lb not 18. I broke a bolt at 18

[@ricardoarias1357]

How did you get it out

[@patrickjohnson7801]

This is not the first time this set has been changed the original set was a dubble row chain and I had to drop the pan , if you use the factory type of plastic cover you can use the better set of gears of you use the Holley aluminum cover with a replable seal You need a thin set like this one or single row chain. I do mine a little different I take a old dampener and cut the shaft off and use it to aline the cover ( seal ) with the crank but pan needs to be lowered but I don't have leaks something you would have to remove the alinement pins . If you have very high mileage put a new dampener on at this time.

[@1AAuto]

+good guy Thanks for the feedback!

[@sebastianmcneilly8623]

My cover bolts are not 18 ftb and now I have a broken off bolt . ... FYI to anyone doing this job the cover bolts are so delicate so be careful or they will snap off on you 😢

[@camillejordan714]

I have a 94 c1500, 5.7 v8. Is this a similar process?

[@dylanbrado4264]

How do you know if it is a non interference motor if it's been rebuilt

[@willyjilly9684]

There's two different size chains for a L31 vortec which one do I choose??

[@1AAuto]

+willy Jilly We do not have any information on the correct size for your vehicle but your dealership should be able to tell based off of your VIN.

[@Leveluplivin]

17:40 question?? A1auto .... So I can make my own gasket sealer for the bottom timing cover? Because I have this thick rubber gasket where you have to drop the oil pan some just to install the timing cover for the bottom rubber u shape gasket to fix properly. What's the name of that oil gasket sealer brand or name?

[@1AAuto]

+Darren Stevens You will want to create your own gasket/seal for that part of the installation. That is just an oil-safe gasket maker that can be found at any local auto part store! 1aauto.com

[@duncanvaughn7586]

So I got one I have a 98 k1500 Chevy my baby but original motor 215 thousand got a tick or I thought it was adjust timeing advance dimed it down I get new battery put in then listen to front where pulley are in front motor and heard the tick their is it ever heard of time chain slapping around and almost like a lifter tick but on front of motor help me if can ?

[@allanbrogdon7453]

On a 350 we were looking.at to buy it sounded like a knock I was worried dad sprayed wd 40 on the belt and it went away.Worth a try don't remember if it was a pulley or belt.

[@angelguaman309]

I understand you guys have to sell your parts to make a living like we all do, but you should warn that this replacement IS COMPLICATED and should-work very careful not to damage the crankshaft’s threads. You make it so easy to replace. GUYS IS NOT SO EASY, PLEASE BE VERY BE CAREFUL. This video they made easy with only purpose of selling you the parts.

[@1AAuto]

+Angel Guaman While some of our repairs may be more difficult than others, we believe that they can all be performed by the consumer. If you are uncomfortable and feel that a repair is too complicated, we do recommend you have it done by a professional. Thanks for the feedback!

[@timbosims4397]

Oil slinger? I thought that brass plate was the reflector gear for the crank sensor....

[@jerrywicker3451]

This needs captions turned on.

[@chadwickperry7700]

So I put a timing light on my truck and it’s showing it’s 8 degrees off. How do I adjust that out before removing the lower sprocket?

[@1AAuto]

+Chadwick Perry We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@Devo1987]

1A auto parts. So On a 1998 gmc k1500 5.0 L 305 serria SL z71 1/2 ton pickup is my vehicle make a non interference engine ?

[@1AAuto]

+Devo As far as we could find, that engine is not an interference engine, but it would be best to check with a local shop or your dealer to be sure. Thanks for checking us out! 1AAuto.com

[@ManuelPerez-gz3ky]

MUCH EASIER TO CLEAN THE AREA WHERE THE GASKET GOES WITHOUT THE GEARS AND CHAIN IN PLACE, NO ?

[@jamessmejkal8803]

Enjoyed the video, but I can do without music in the background. I do not know why everyone thinks you must have music with a video, such as RTV ( thread sealer) on threads going into a water jacket and I was wondering about the "oil slinger". Thanks for the list of items needed for the change.

[@1AAuto]

+James Smejkal Thanks for the feedback!

[@ColoradoMelons]

Hello. It isn't an oil slinger. The part he decribes as one is actually the Crank Position Trigger Ring. It is what the cover-mounted Crank Position Sensor uses to create a reference signal to the ECM.

[@dailyvlogzz123]

Oil slinger ain’t coming off it’s stuck like glue?

[@91CTD]

That's the crankshaft sensor reluctor wheel, not an oil slinger.

[@Devo1987]

Do you have to drain the oil in order to change the timing chain cover ?

[@1AAuto]

+D.L.P You do not need to drain the oil to perform this repair! 1aauto.com

[@wadeyarbrough5731]

@@1AAuto do I need to drop the oil pan? And will I need a new oil pan gasket?

[@1AAuto]

+Wade Yarbrough Thanks for watching! No you do not need to drop the oil pan in order to perform this repair.

[@ThatSaskGuy]

This does not comply to a normal 5.7 chevy, only the vortec

[@b_wilk98]

Is this similar on a 4.3 vortec?

[@1AAuto]

+Brandon Wilkinson It may be a different procedure on that vehicle. 1aauto.com

[@singlepistonproductions3232]

Can I have a link for a timing chain for a 1996 Chevy 1500 extended cab 4x4 v8 5.7L?

[@1AAuto]

+Keagan does Things Here is a link to the timing chain that we carry for your truck. We are currently out of stock on them goo.gl/eta1sP

[@trillrifaxegrindor4411]

exact same proceedure

[@stephenhardaway7821]

did you have to pull the spark plugs to do this?

[@1AAuto]

+Stephen Hardaway Thanks for watching! No you do not need to pull the spark plugs to perform this procedure.

[@sandiegojody]

Hello, will this be similar to a 1994 Chevy 5.7L?

[@1AAuto]

+Jody Castro This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c

[@michaelknight7684]

@1aauto so you had no slack in the chain?

[@1AAuto]

+Michael Knight Thanks for checking us out! This should fit in very snug and not have any excess slack.

[@wadeyarbrough5731]

Do I need a new oil pan gasket to do this?

[@1AAuto]

+Wade Yarbrough We suggest replacing it if you are in there.

[@etceteraleatherworks1103]

It's much easier to seat the timing cover if the oil pan is hanging loose just a bit.

[@wadeyarbrough5731]

Did you need a new oil pan gasket? I got a 96 c1500 305. V8

[@heavychevy2289]

Oil slinger... I thought it was the reluctor ring.

[@jessehulbert6524]

That was funny

[@jameskelly2094]

Is the reason you replace the water pump cause it was bad?🤔

[@nolanmiller2035]

Is it a vortec 350?

[@AFatherToTheFatherless]

Yes 5.7L

[@terrysmith147]

Looks alot like the dodge durango under the hood.

[@benjiminbliss1016]

Can this prevent my vehicle from running totally?

[@1AAuto]

+Benjimin Bliss We wouldn't be able to diagnose an issue like that here, but you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com

[@dawsonscruggs1609]

Soooo i dont need to take the oil pan off?

[@1AAuto]

+Dawson Scruggs Thanks for watching! No you do not need to take off the oil pan if you are performing this repair for this vehicle.

[@mikeb9478]

followed the video and have no spark what could the reason be ?

[@1AAuto]

+Mike b We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@grndzro777]

I don't see anything wrong with the old one.