2 Way HiFi Speaker Crossover

This video show you how to make audiophile crossover speaker specially 2 way crossover for 8ohm midwoofer and 8ohm tweeter with Lpad for Hf level control.
this diy 2khz crossover suitable for home use.
please follow the instructions for good results.

[@f.8084]

This is BY FAR the best video I've seen on how crossover looks and works... I am building my own home theater setup and this helps me understand! By chance, can anyone help me with crossing over? I don't want to mess up with this project..

[@ericschulze5641]

I've spent countless hours over the past couple years, not using a computer, but a graph, if you notice even the so called experts, end up swapping caps and coils, after all thier computer designs. Just buy a bunch of coils and caps and test test test, you can use cheap ones if your only building 1 set then build your final crossover with quality parts just use the Dayton caps thier cheap and sound better than the expensive ones Jantzen coils are probably your best choice for coils unless you want to spend a lot of money

[@marian-uy2fn]

Yes indeed

[@ilhamprakoso3844]

Good video mate ! Maybe you can explain about how choose the component value with the Freq that we want to. It will be helpfull

[@soundcoremusicmix]

Awesome! Nice for Bass & Treble music like EDM genre., 🎧🎶🤩

[@homemade_audio]

Thank you 👍

[@ndodhy]

Very nicely described a crossover and connections. 👍

[@homemade_audio]

Thank you 🙏

[@charitofran3382]

thanks for sharing. god bless.

[@ShadowPuppit]

Fire only things that's bothering me why didn't you just add another potentiometer in for separate volume control or just tie it in by putting it at the beginning then branch off into the tweeter and midwoofer and can you add a parts list in the description? Other than those two things I thank you because this was so helpful!

[@homemade_audio]

Exactly

[@creativeandinnovative4932]

Thank you for the video and I will do mine as well bro😁🤝

[@homemade_audio]

🥰🥰🥰👍👍👍

[@djordjejon4849]

Exellent main frend 🍻 My greetings from Serbia 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@djoso559]

What’s the extra banana plug for.looks like you coulda soldered the red and black cables being used to jump to the other side? Great video though.could you add a small detail what each do to make it work.

[@Ozzypants2020]

Yeah I’m confused about that. It looks good and simple otherwise but for essentially what’s supposed to only be one 2 way speaker should only be a right or left channel which should only require two banana plugs

[@alexanderdubois3579]

Also looking for this answer.

[@user-lq8gr6mw4g]

Здравствуйте ! Не понятно то как подключили ? Тоесть начало намотки пошло к динамику , а конец ко входу терминала ; на сколько мне известно от терминала ко входу и конец соответственно к динамику . Спасибо за познавательное и доступное видео - любой Человек может добиться для себя результата , посмотрев , и используя только свои уши - при навесном монтаже , хороших результатов . Благодарность зрителей

[@fernandoflorentin898]

Que función tiene la bobina de 0,33mh y el capacitor para el bajo en paralelo?

[@djashofficialsounderz.pro.6992]

Bro i have 2 top to way 12 inch speakers one top 400w i need a information from what capacitor i can use in parallel the woofer to get mid bass please help..thanks you

[@homemade_audio]

Crossover cut frequencies not àdd frequencies!!! We can make equalisation modification on crossover but just for few decibels. You must check the ref of your driver on Internet to see the response diaphragm.

[@Sandokans]

Subbed to your channel!! Thanks for your work

[@homemade_audio]

thank you 🙏🙏🙏

[@marian-uy2fn]

Do have a 1500 watts for this ?hoping you make one for diy thanks in advance

[@simonskidz]

Nice video but where is the source coming from? I don't see where the amp is connected. It's NOT connected the speakers nor does the diagram make mention of this.

[@husamettininan4367]

Netice mükemmel teşekkürler 🙏🙏🙏

[@rickwalicki7057]

Not real talkative…..but a pro with the soldering Anks for the video!

[@homemade_audio]

🙏

[@giovannipg3000]

Hello I got 2 speakers from wherfedale model valdus 400 and there are no cross inside only capacitor on tweeter. What can i make for the valdus 400 ???

[@YusufGinnah]

Hi Giovanni, most ready made speaker boxes have a single midbass/woofer to handle all the frequencies except for the highs. And they normally have either a 2,2uF or 4,7uF capacitor in series with the tweeter. This is how it is designed and will not sound better any other way. 😎👍🏼

[@giovannipg3000]

In this speaker enclosure there are 2x 8 inch woofers and 1x 1inch tweeter so the original crossover is not in the enclosure...i want to make a 2 or 3way cross over filter for the speakers so that the bass and high sounds warm and clearly.

[@grob318]

Thanks for the nice video. I am assuming this is a 3kH crossover. What ohms? I am trying to recreate a JBL Control 1 crossover and the original crossover is 6kH and 4 ohms. What uf capacitors would I need to substitute for 6kH? Thanks.

[@homemade_audio]

Thank you for your nice words, i do this because i love sound 😍😍😍 For 4ohm 6khz high pass try second order filter based on 4.7uf cap in serie + 0.2mH inductor on parallel, 0.5mh in serie + 10uf in parallel for low pass.

[@homemade_audio]

And sûre lpad for tweeter to control level .

[@grob318]

@@homemade_audio Thanks, I had to figure out how to get capacitance and inductance values in series, but have it now. JBL Control 1 are about 80hz to 18kHz and they also have an SK3 light bulb as an overload protection and have a 5W 5 ohm resistor which I think I'll replace with an Lpad.

[@jonathanharris3049]

Did you mean 1.2mh instead of 0.2mh?

[@thomasschafer7268]

Sorry datasheed says 4.2khz

[@humnaset]

Channel keren nih....

[@homemade_audio]

terima kasih 🥰

[@igors.5514]

How do I know how much power can withstand crossover?

[@35sonmen]

speaker resistance and crossover cutoff frequency are not very important? coil and capacitor values ​​depend on it.

[@homemade_audio]

Hello, you're right, but you have to read description before. To make crossover there're more important things to keep in mind like TS parameters and distortion/ response diagram. You welcome 🙏

[@fightinggamer9450]

If amifier is 4 ohm 150w then now many twitter of 8 ohms I can connect with it ?

[@cdps82]

18 dB/Oct high crossover for the tweeter and 12 dB/Oct low crossover for the woofer? Sure you don't need to mention the phase shift of the input signal in between the speakers?

[@brendonhauschild5248]

How many mH are the inductors ?

[@homemade_audio]

Hello, i have mentioned the values of all components on the video parts section 0min 50s

[@vlogndesochannel]

Bagaimana cara membuat lilitan kawat tembaga untuk crossover ??

[@Tasking0830k]

i well use only active crossover ist cost lot of power output

[@homemade_audio]

It's better to start with passive crossover if you want to make speakers because it's easy and doesn't cost much money. If you make a mistake in active crossover settings you'll destroy your hf drivers immediately. Don't forget to put 50uf caps between amp and hf driver for safety.

[@ladysmusic2932]

Sy punya twiter 3 inch,untuk mendapatkan suara high yg bgus,brpa nilai capasitor yg harus sy pke Terimah kasih

[@homemade_audio]

Anda harus terlebih dahulu mengetahui respons terendah dan impedansinya, kualitas suaranya tergantung pada kualitas tweeter dan kualitas kapasitor (sebaiknya mkp).

[@nooromi]

helo po pwede ba gumamit dalawang crossover in one channel output

[@danielfelipelauretta7615]

Hola el negativo no va en la otra punta del atenuador es decír pata más larga

[@homemade_audio]

el montaje es correcto, la señal llega a los extremos del atenuador porque el montaje es un divisor de voltaje (desde -1db hasta el infinito), el otro montaje sin cablear el otro extremo es un montaje en serie a partir del cual la atenuación es de unos decibelios.

[@dighuman1389]

For Mid and HF?

[@truthvoice9945]

Where do you get your parts from? I'm in Australia.

[@homemade_audio]

This links for original parts shop : www.hificollective.co.uk/componentshome.html www.banzaimusic.com/Electronics-c-1664/ www.audiophonics.fr/fr/condensateurs-selfs-bobines-hifi-c-6339.html

[@truthvoice9945]

@@homemade_audio Thankyou

[@adilfachatti2963]

Coool

[@humbertoqueiros9438]

At 2:45, Lpad 8 ohm, is it a wire attenuator?

[@homemade_audio]

Yes

[@MrPstandel]

Can I use potentiometer? N if yes which value

[@homemade_audio]

@@MrPstandel No. Lpad doesn't affect the impedance and supports power not like Potentiomètre.

[@salbahebf]

@@homemade_audio will it be okay if i dont have that Lpad

[@homemade_audio]

@@salbahebf ok it works, but you have to add resistor in serie instead lpad to control the level of HF response, same for midrange if it's level too high, it depends on the sensitivity of drivers used.

[@serhiisamoilenko3975]

What’s capacitor in bass line?

[@homemade_audio]

look at 0:29

[@kangmabreb_2258]

Elco size 36 uF 100v

[@ghostofkadesh9041]

🙂👍

[@vuilledeeresh4116]

Tried this but i had a big dip 1-2k regarless of polarity 😂

[@om7585]

los diagramas y los componentes

[@homemade_audio]

todo se nota en el video, ver 0:20min

[@Shailesh-sq4ty]

750 and 550 hf ma

[@markeyeconas4491]

Ilang po yung nagadtos mo Dyan sir

[@homemade_audio]

hindi ko naintindihan tanong mo!!

[@Paul-dv8zf]

​@@homemade_audio what is the cost of these parts to make the crossover

[@fabioramos8562]

Please diagram

[@A2Dsoldier]

Thumbnail