2002 Polaris Ranger 500 2" Lift for The Front

[@mossman381]

Things that might help with a project like this: 2" Front Lift: amzn.to/2T0ealG This video contains affiliate links, which means that if you click on one of the product links and buy, I'll receive a small commission.

[@rikleavitt2966]

Just what I needed, Thank you for the Video, Made this very simple and easy. The written instructions were looking pretty ominous.

[@mossman381]

Glad to help.

[@mossman381]

It's an impact 1/2" to 3/8" adapter.

[@jessepayne6757]

Have you had any issues out of the spacers?

[@mossman381]

No

[@allied1394]

Looks good nice and level I like when they sit level to makes a big difference not to much work either throw some nice lights on the front where that guard is on an angle from the headlights just below would look good and would fill in the front nicely

[@terrellrieger3314]

Will it fit a 2001 Polaris ranger 500

[@mossman381]

Yes

[@MOUSEBOWEN]

Awesome video

[@chrishester6999]

Where did you get you rear view mirror? I've been looking for something like that for my Polaris Ranger.

[@mossman381]

EBay, I think I have a video on the mirror in the playlist of this ranger.

[@mossman381]

Here is a look at one on my 6x6. kzbin.info/www/bejne/pnu5oqBmn56Kp8U

[@mossman381]

I have plans for better headlights if that is what you are saying.

[@nathanw5747]

i wish your kit was the one with the rear lift also . i cannot figure out the rear section of it

[@mossman381]

I am not familiar with the lift for the rear of these older Rangers.

[@MOUSEBOWEN]

Where did you get this 2” lift . Could you please tell me the part number. I want to install a lift on my 2002 Polaris Ranger 500 4X4

[@mossman381]

Check the description or top comment. I have a link.

[@MOUSEBOWEN]

@@mossman381 thank you so much

[@shanefrench5446]

Where did you buy the spacers

[@offthestreetsandinthecreek7294]

Does these work on the series 99 Polaris rangers 6x6 (99-01)

[@mossman381]

I am not really sure about those first Rangers. I have never had one.

[@slowride55]

Whats that thing on your ratchet? Looks like a 1/2" to 3/8" impact adapter lol

[@budmoore8144]

GREAT VIDEO

[@mossman381]

bud moore Thanks, I miss that ranger.

[@timgile8891]

You didnt have to do alignment after lifting ?

[@mossman381]

Tim Gile There is no adjustment except tie rod ends. They were fine before the lift so don't know why it would change after. This will cause you to have more camber but really it isn't that bad.

[@ericrodriguez4379]

Where did you purchase the spacers?

[@mossman381]

Ebay

[@powermods3154]

Y is my carb pissing gas out only when I'm on the throttle but when im idling it's fine .

[@mossman381]

Not sure. I have had a few of these older Rangers and noticed carb leakage on them. Not a lot of fuel but enough to leave a stain.

[@nivenmartin2841]

about how long to do it

[@mossman381]

30 minutes maybe.

[@nivenmartin2841]

mossman381 would it fit a 2004 TM its the same thing i think it just has a smaller motor im new to the side by sides so i don't know much about them

[@mossman381]

The front suspension will be the same to 08. The TM was a 2 wheel drive Ranger with a V-twin motor. They might also be geared a little lower than the standard Rangers. That motor isn't that much smaller than the normal 500 that most of them got. I had a TM a long time ago.

[@nivenmartin2841]

mossman381 do u think that lift would work bc I found it online for $50 and i was trying to figure out if it would work before i ordered it

[@mossman381]

Ebay

[@shanefrench5446]

Nm I see you got it off ebay

[@gravely86]

You gotta but better yea lights some how

[@george6571]

Where did you order the spacer at

[@mossman381]

Ebay