2004 honda crv p1077 IMRC

P1077 HONDA Possible Causes Faulty Intake Manifold Runner Control (IMRC) Valve IMRC Valve harness is open or shorted IMRC Valve circuit poor electrical connection
in my case the Intake Manifold Runner Control Valve is bad after i replace it the problem is solve.

[@michaelwhitacre8499]

I just dealt with this code. It was just a disconnected vacuum line directly under the imrc solenoid, it's very short and easy to miss. Plugged it in and cleared the code and it's all good now

[@carlito3094]

Nice thank you... I have the problem now .. time to get to work ...thank you again

[@reynaldooolm00tubban9pllw9]

how to replace the injector of crv model 2003

[@topgun176]

Wow Very good VDO. Thank you very much for sharing this VOD.from thailand

[@alltsab]

Thanks

[@Para-ni5lx]

THANKS for this very informative detailed video!! Very helpful

[@alltsab]

Unwelcome

[@michaeldarrow6021]

Thanks for your help..... however the "snickers chomping" sound towards the end was abit disgusting

[@jdmbebo4342]

You didn’t have to remove the coolant hoses at all… the top of the rad support comes off

[@topgun176]

Good vod

[@anujkishor]

super helpful man thank you thank you

[@alltsab]

You welcome 😉

[@cobbles62]

What is the function of that check valve in the vacuum line? I don't think it is originally put in and to be honest, installing it later does not make sense. The IMRC valve is supposed to move back and forth based on engine RPM and this check valve seems to keep the valve activated while preventing it to ever deactivate. Is it maybe a mechanic's dirty workaround to hide a membrane that starts to fail?

[@josearivera3371]

Idid the same job to my crv dont need move the power steering pump

[@thexflexclan]

I remove the intake today just to replace the starter k. This 05 and it’s a nightmare but I’m ending up getting the code i noise one of those little house that was loose and and put it back but

[@Para-ni5lx]

Yes. That’s what happened to me after i just replaced the starter. P1077 code appeared and this video helps

[@tamerelsafty6588]

I know it's been a long time. Do we need to take the whole thing out to change just that sensor? Thanks in advance.

[@alltsab]

The whole thing

[@victorp7555]

Yes

[@h0ng_stuff]

Can I remove that small sensor by removing the power steering pump instead of removing the intake manifold? Looks like you can get to the two small screws to remove the sensor that way 🤞🏼

[@NobodyLikesTheTunaHere]

I hope so! Were you able to remove this sensor in place, or did you have to remove the intake?

[@victorp7555]

There is no room

[@gmoneyga84]

Is the real reason for the code is that the solenoid failed? which doesnt appear to be attached to a new IMRC-- ( I'm having the same issue)

[@polymetric2614]

i have this code and my solenoid's good

[@victorp7555]

Generic code for Imrc not working

[@joeymegel5894]

Where did you find that part at advance auto and AutoZone didn't have it in there system also what's the exact name or part number

[@ac_tv2050]

I have p1078 code, I replaced the sensor then the code went back p1077. Any suggestions? Thanks!

[@alltsab]

Clean it and Check for wire connection

[@puerco567]

So What are the symptoms? My 02 crv after warm up going on the road when accelerating at 2800 RPM light comes on and hesitates while accelerating or Intermittent but if I reset it drives well until I press the gas all the way down What is it?

[@alltsab]

Any engine code ?

[@puerco567]

@@alltsab p1259 P0154 but sometimes no codes but light comes on did replace VTC

[@alltsab]

@@puerco567 according to your hesitate i believe the p1259 is causing it

[@alltsab]

@@puerco567 did you buy cheap ebay or Honda vtec aftermarket part from ebay some time it's doesn't work.

[@puerco567]

@@alltsab Sadly yes I ordered from Amazon but today I finally fixed I cleaned the old one with laundry detergent and soaked with rubbing alcohol then I installed and I added some clean oil/new filter My CRV has 278Kmiles and now runs perfect.

[@mambrinox]

It seems you wasted your time removing the intake instead of the sensor only

[@victorp7555]

Good luck getting to it in the car 😂

[@dufourrichard856]

Did he say when you apply voltage to the upper two prong sensor, and it clicks, it's then considered to be bad?

[@ericmadx3063]

He gives no details just replace sensor lol

[@DustinRogersinMO]

No, applying voltage activates the solenoid. If you hear it click when applying voltage it’s working as it should.

[@OryanTv]

is there gasket to intake manifold?

[@roccocroce]

theres two figure 8 gaskets pressed into a recess in the plastic manifold

[@TruckThisGarage]

Do you have the part number for what you replaced. Thanks

[@alltsab]

No

[@hectorquintanilla6153]

@@alltsab what’s the name of that sensor?

[@westicle9812]

@@hectorquintanilla6153 intake runner control valve standard motor part 37890PNDA01

[@saidalghafri3111]

I have problem of RPM it's going up 3 only please i need help HONDA CRV @2004

[@drappointment4509]

My 03' CRV was doing the exact same thing! It was because I had low oil, go get your oil and oil filter changed it should solve the problem 👍

[@bareqn8626]

Watched for the cleaning, then you didn't show us -_-

[@AR-du2is]

What’s that sensor called? the one you changed.

[@thrashingcows8610]

I believe that is a TPS or Throttle Position Sensor

[@westicle9812]

intake runner control valve standard motor 37890PNDA01

[@The1andonlyification]

Hello there. 2006 Honda CR-V code P0661 Intake Manifold Tuning Valve Control Circuit Low Bank 1. Could that same sensor be the cause? thanks.

[@alltsab]

Yes similar issues check as this video inspection to see it help solve your problems

[@elpescadorpr2505]

what was the problem ? i have the same code P0661

[@42santana]

Could you replace the part for me for my 2002 honda crv. I live in Westchester county, NY

[@rusoperformancerd5306]

I can delete this valve colector

[@gaithmarji]

What is the part number or the name of the sensor

[@alltsab]

Sorry i forgot

[@TheBest-no9mh]

37890-PND-A01 part number and it is called SENSOR ASSY., ANGLE