2005 Silverado Duramax Steering Clunk FIX

[@mossman381]

Things that might help with a project like this: Steering Shaft: amzn.to/2Uh9yd9 Column Bearing: amzn.to/3cmNfsn Steering Wheel Buttons: amzn.to/2XOSTyt This video contains affiliate links, which means that if you click on one of the product links and buy, I'll receive a small commission.

[@HODMEChannel]

Glad to see the new Duramax videos! Glad you found another diesel Randay!

[@blakeb1992]

I cant wait for the exhaust upgrade episode!

[@mossman381]

Been looking at a few. I always wanted to dual out my dually but might just go single on this truck.

[@adamr.bellinger385]

Great video! Thanks...gonna tackle mine this weekend! DIY 💪🏽

[@mossman381]

Good luck!

[@jewllake]

that's a beautiful truck! I really like that front end!

[@mossman381]

Really loving this truck. Even more so with the little issues getting fixed. I miss the diesel more than I even knew.

[@hollywd269]

I did this to my 2004 2500hd. I only replaced the column bearing with the same dorman product as you showed in your video. After about 6 months the clunk returned but never as bad as it was to begin with as has never got any worse so it still is a bit noisy however you have to be hitting some fairly big pot holes. But just a heads up you clunk may come back but not as noticeable as factory bearing. Awesome video. I have one up about it as well but you definitely got better angles on it.... thanks for sharing

[@mossman381]

Would have gone OEM on the bearing if I knew mine was loose but Dorman was the only one I could find local. Shipping on things has slowed down a lot and didn't want my truck sitting for a week. I did feel some slop in the shaft as well. I think I would recommend doing the shaft and the bearing to get the full new feel. You have to do half the shaft job anyway. I will report if mine comes back.

[@mzElvie91]

If you have the green bearing on right now you can try this: kzbin.info/www/bejne/oKu7ZJWkgMR_sMU

[@itsmemaaaark]

@@mzElvie91 that's why I did the second time around replacing both bearing and ISS twice. The ziptie and radiator clamp did the trick for me. Just wish I knew this the first time I replaced it...

[@billdurnce]

Been needing to do this on my Lb7. Great video!

[@mossman381]

Not that hard at all.

[@farmboy30117]

I hate working under dashes! Good tip about spinning the wheel! Save the clockspring!

[@sirsweetness8332]

How are those Dorman parts holding up

[@mossman381]

You will have to ask the new owner. I traded this truck in for my 2009.

[@jamesphillips7283]

How many times did you have to keep replacing Dorman parts. Firestone replaced mine next day was still popping/ clanking

[@mossman381]

This fix worked for as long as I had the truck. I traded it in for my 09 I have now.

[@riveraf5053]

Does this help with loose steering??

[@mossman381]

I don't think it's going to tighten up your steering. That would be in your steering box, pitman arm or tie rod ends.

[@happytrails1963]

Good looking truck!

[@8luggarage]

Would pulling the key and locking the steering wheel keep it from turning?

[@mossman381]

Not sure the steering locks in this generation truck.

[@danielmartone3179]

Randy are you happy that you got another duramax

[@mossman381]

I am loving this truck. Wish it was 4x4.

[@brendan747]

mossman381 all you have to do is swap it and you’ll be in business

[@flfarmboym7507]

Thanks for info

[@ef2967]

Did this on my truck. Hardest friggin piece of plastic to get out and back in.

[@TeamDaenzer]

my dad is trying to get some tow mirrors on his 05 silverado but can figure out how to

[@mossman381]

They should have bolt on mirrors for a 05.

[@TeamDaenzer]

@@mossman381 he don't know how to take all the electrical stuff out then put it together

[@mossman381]

All the extra lights will have to be wired the way you want them. It can get complicated.

[@JohnDeere50d]

Need to do this to my truck. It's been making noise for the last 4 years lol

[@mossman381]

It's really not as bad as it seems.

[@tjfountain7223]

I sent you a message on PRC forums...need some ranger wiring help please

[@northface484]

Don't waste your time...Buy the Bearing from Wolf Engineering....No more clunk on my 2007 Duramax Classic...

[@sirsweetness8332]

Dorman 👎🏻

[@AaronBeihl]

What manufacturer did you use in place of doorman for these parts?

[@BenKempa]

Aaron Beihl personally I only use GM parts on my truck.

[@mossman381]

A lot of people hate Dorman but they are priced right and available. I have had good results using Dorman parts. Can't say that about others. If money is no object go ACDelco.

[@samsquires2877]

Ive not had good luck with dorman. Most the time its cheap junk. I use GM every chance I can.

[@samsquires2877]

Aaron Beihl use the OE part manufacturer you can’t ever really go wrong that way.