2007 - 2010 Jeep Wrangler 10" Radio Install | Dual DMCPA11BT

Parts linked in the description below!
Watch a full tutorial as a Jeep Wrangler Unlimited will have a giant 10" Dual radio installed. We will be using the Dual DMCPA11BT float mount touch screen bluetooth radio. This radio features Apple Carplay and Android Auto.
Click here to see the Radio Unboxing of this Dual 10" Screen:
• Huge Dual 10" Radio Un...
Click here to see a backup camera install of this jeep:
• 2007 - 2017 Jeep Wrang...
Click here to see the Crux wiring harness unboxing video:
• Crux Chrysler Jeep Dod...
Click here to see the amplifier and subwoofer install video:
• 2007 - 2018 Jeep Wrang...
For the front component speaker install, click here:
• 2007 - 2018 Jeep Wrang...
For the rear tower speaker install, click here:
• 2007 - 2017 Jeep Wrang...
This video applies to Jeep Wrangler models for years 2007, 2008, 2009, and 2010. This video also includes complete radio wiring, complete installation, and testing.
If you have any questions, leave a comment below! Be sure to like and subscribe!
Parts used in this install (Amazon Associate Paid Links)
*Dual DMCPA11BT: amzn.to/3dqSOcP
*Crux SOOCR-26 Wiring Harness Adapter: amzn.to/3h6bRvo
-Note: If you have steering wheel volume controls, use Crux SWRCR-59: amzn.to/3hoiKqS
*Metra 95-6511 Double Din Dash Kit: amzn.to/3dngoab
*Metra 40-EU10 Antenna Adapter: amzn.to/2UKAuop
*USB/USB 3.0 Flush Mount Adapter: amzn.to/2URnTA0
Disclosure: As an Amazon Associate I earn from qualifying purchases

[@ProvoBeastAudio]

Parts linked in the description below!

[@alvarado5142]

is compatible with Toyota Corolla 2007

[@fly7881]

Great video 🙂

[@JKeye]

Where does the purple wire go from the crux to the aftermarket

[@marlongarcia8558]

I have a 2005 f150. I tried to install it but all it says is no signal video camera and that’s it. Doesn’t do anything else. What am I doing wrong?

[@gregbell5975]

Nice I feel better about putting in the exact replacement. Hope it doesn’t need to be reprogrammed!!!😬

[@angeldiaz3754]

Do you know when this unit will be available again?

[@oXHALFSOUL87Xo]

How did u use the orange wire

[@dylanmuoio1404]

Did u use the long nose or short nose for the mounting brackets

[@garydelr5757]

Great vid! Do you have a link fir the dual USB port?

[@bossman77420]

I tried to install 1 of these stereos ina 2013 Wrangler an the sound wouldn't work but came on twice then wouldn't work again

[@erichebert4776]

My radio harness has a blue (power antenna) and a blue/white (amplifier). The jeep in this video and mine as well does not have a power antenna but has the amplified system from the factory. It appears that you hooked up the radio blue to the Crux harness even though there are no power antennas. You left the blue/white open for a future amplifier. Does the blue wire you hooked up turn on the factory amplifier? Or does it not matter because both the blue and blue/white wires are both triggers? Thanks for the informative video!

[@djwhokid2]

Link for that radio I can’t find That exact one ?

[@johnathanlopez4012]

Why’d you take out the bracket I didn’t have too🤨

[@lalp01]

I got the same radio and followed all of the installation instructions. However, my 2007 Jeep has a subwoofer which technically makes it an amplified system, right? Anyways, the person that helped me connected the harness the non amplified version. The radio powers up, connects via bluetooth, but does not have actual radio, microphone not working, and jumps automatically to the phone as if it were to dial a number. Bluetooth works well, and the backup camera works great. Any suggestions? Thank you!!! Great video. If we would have followed it to the T….. Thanks again

[@lalp01]

Got everything squared oiut and all is working fine. Camera, bluetooth, USB, carplay, reverse camera. Now waiting for the appropriate cable adapter for the video.

[@openhousepro]

I bought the same exact unit and have the same exact Jeep. I got everything to work but my back up camera isn’t starting when I go in reverse. It was working fine with my stock radio(same one you took off). How do I set up the camera harness for this unit?

[@Flowe_Grading]

I had issues with hooking up my backup camera as well. Just make sure to wire the red camera 12v wire to the red pig tail on video wire as well as the reverse wire together. Then at back splice power wire for camera to your reverse light power wire then run it to camera and splice the other end of the video cables red pigtail wire with the red power wire for camera

[@romeorojas5257]

I have a jeep wrangler 2010 non amplified, I installed everything correctly as well as installed the brake camera and wired it to the reverse light, everything works perfectly however after about 5 min or so of starting the vehicle the radio begins to start turning off and on continuously at about 5-10 second intervals any idea on what may cause this problem?

[@luism8612]

We’re you able to fix this??? I’ve been looking to buy this head unit but am worried keep seeing people have this issue

[@cuzimadapapushkian799]

Great video. I'm installing a Kenwood head unit into a Ram and I'm using the same interface as you. One question...how do you know if your using amplified or not? Thanks

[@dylanmuoio1404]

I would like to know this as well

[@rticul8862]

@@dylanmuoio1404 if it isn't a special alpine system, bose, or beats then it doesn't have an amp.

[@JKeye]

Where does the purple and white go from the crux to the aftermarket

[@ProvoBeastAudio]

Reverse trigger wire. If you don't have it, it doesn't need to be connected.

[@Zero3ree]

Is there any difference when there is a factory subwoofer as well as the amplifier?

[@ProvoBeastAudio]

Nope, this model had that same trim level as well. The parts linked in the description work for any trim level jeep.

[@thaugo51]

If you have a 2007 jeep wrangler with no steering wheel buttons, what if you bought a steering wheel with buttons? could you connect all of those wires to where it is able to use steering wheel controls?

[@ProvoBeastAudio]

That question has come up before. From our research, the clock spring can accommodate a new wheel, however, the body control module / can-bus system isn't programmed to accommodate steering wheel controls. Even if you installed one with buttons, you would have to find a shop to flash the system to recognize steering wheel control buttons are present.

[@tiwanda25]

Can I put this radio in a 2014 Chrysler 300?

[@AndreBarnett]

I’m glad you already asked the question lol

[@user-rk2mz9vx1b]

I only have front speakers. When I change my balance and fade to the front I don’t have any sound when I change balance and fade to rear my front speakers work. I’ve wired color to color. I wired color to color with the amp and plugged in the “ without amp plug”. Do you think I should switch to “amped” on the plug or do you think I should wire it as an amped system white to green/white etc?

[@ProvoBeastAudio]

You need to wire the front speaker wire outputs of the radio to the rear speaker inputs of the wiring harness adapter. (radio to harness) White to Green, White / Black to Green / Black, Gray to Purple, Gray / Black to Purple / Black. It explains it more here: kzbin.info/www/bejne/omOrkpZ3atumn7cfeature=shared&t=233

[@obuchiteck]

How do you tell if it’s amped or not?

[@ProvoBeastAudio]

If you have the non-amplified version, you will have four sets of speaker wire outputs in the factory wiring harness adapter. If you have the amplified version, it is only two. This video will help you out: kzbin.info/www/bejne/d3OVm5yorrGgnZo

[@DjBigTon]

What if I have the factory amp in 08 jk?

[@ProvoBeastAudio]

The crux adapter works for the amplified trim as well.

[@jbrown27b]

does this system have gps built in to it ?

[@ProvoBeastAudio]

Via smart phone, not native. All runs through apple carplay / android auto using your phone's GPS.

[@AntonVoshwitz]

Don't know if you're still replying but It seems that mine has a high pitch noise whenever it's on coming through the speakers not affected by speed, any idea what it could be?

[@ProvoBeastAudio]

Depends on your wiring, and the harness adapter used. Lots of variables there, but sounds like ground loop noise.

[@racegarage3754]

I’m having the same problem, nothing affects it. The noise goes away when I turn the radio up, or mute the radio. Also thank you for the video, it helped me a lot. Just installed everything on my 2008 wrangler!

[@Golferdrew1]

How can I make the factory sub work with a after market radio