How to change engine oil and filter on 2010 Toyota Corolla
Пікірлер: 89
@robertblacksmith43552 жыл бұрын
I feel so much better with fresh oil in my engine.. Ciao!
@303MoTo2 жыл бұрын
I just purchased 2009 1.8L Corolla for my daughter, the last few videos have been perfect for me to learn how to work on her car, thanks! Now I just need a lift in my garage!
@captainamericaamerica80902 жыл бұрын
NO YOU DON'T. USE A JACK AND Stands
@rick31869 Жыл бұрын
i use a small floor jack and jack stands , be aware of that retaining clip that keeps filter from unscrewing , get the filter cap that fits on housing and be careful !!!
@mannys91302 жыл бұрын
So many people overtighten the drain plug and the filter cap. The plug only needs to be tightened to the point where the bolt stretches into elastic deformation and applies enough stretch and friction onto the threads to prevent loosening. It is NOT much torque. Tightening to plastic deformation ruins the threads and they will come out eventually. Same for lug nuts/bolts. The cap seals on that O-ring. These are not pipe threads. 😸😸😸 The cap only needs a small snugging torque and that's it. The O-ring seals it, and the elastic deformation of the threads keeps the cap in place. I've seen so many overtightened like this one, and it will eventually crack the cap and then you have a pressurized oil leak. 🙀 Not good. When I bought my 2012 Corolla used, I replaced that oil filter cap with a brand new one from the dealer because there's no way to know who abused it in the past and how close it was to breaking with further use. It was not expensive. I highly recommend replacing it anyway after 60-75k miles even if you are the first and only owner and did all the oil changes properly from change #1. It's good, cheap insurance!
@joshhemingway5 ай бұрын
Everyone should buy one to have an extra one on hand anyways! That’s a good plan around 60-70k 👍 completely agree
@حامدشهاوى2 жыл бұрын
Hello my friend welcome back 👍
@jamesharris5185 Жыл бұрын
Never have I felt so relaxed watching a repair video thanks Sir!!
@rmcracing692 жыл бұрын
I also take a small dab of oil and lubricate the o-ring at the top of the dipstick to prevent future sticking of the dipstick.
@joshhemingway72942 жыл бұрын
Guess you didn’t pay attention, cuz he did exactly that😜
@darrenairey59385 ай бұрын
@@joshhemingway7294Guess you didn't read the comment properly, he was talking about the o-ring on the dipstick not the o-ring on the filter canister!😜
@HAL-dm1eh2 жыл бұрын
That plastic oil filter canister was the worst design on the whole car. Everything else was actually well engineered. I had a lot of trouble getting that filter off and finally found a trick. Use one of those specific wrenches like you showed, and tap/hit the handle of the ratchet with a rubber mallet. This will slowly and gently break it loose. It's like a miracle it happened so easily. Unfortunately the first time I changed it I also put the o-ring in the 1st groove and after all was done and I cranked up the car, oil sprayed out all up under my engine, bottom of car and the ground. It was very scary until I figured out what I had done. Of course I immediately shut off the car and fixed that issue and I had lost so much oil I had to put I think 3 more quarts back in.
@SaltGrains_Fready Жыл бұрын
IS there not a metal aftermarket upgrade to use in this ?
@HAL-dm1eh Жыл бұрын
@@SaltGrains_Fready There is but the spring inside isn't up to Toyota spec. I watched a video of a top notch Toyota tech and he suggested only using OEM Toyota plastic canisters. He said aftermarket plastic canisters won't last long, but I do have one on mine and it's lasted for many years and still going. Since tightening it to a reasonable level, I've had no trouble getting it back off, and it's no big deal.
@joshhemingway5 ай бұрын
There is an OEM metal one get that, around 50 bucks get one
@SilverIndian2 жыл бұрын
We should have such a good Toyota mechanics, to share their knowledge, also in Europe.
@BenJammin4272 жыл бұрын
Just bought those drain plug gaskets for my 2010 Corolla, thank you sir!
@Val1414_2 жыл бұрын
Great video. you've remind me of what someone once said❤️ "The mind is the man, the poor is in it and the rich is it too". This sentence is the secret of most successful investors. I once attended similar and ever since then i been waxing strong financially, and i most tell you the truth...
@daveyboy69855 ай бұрын
That is an absolute stupid oil filter design, should be the normal steel screw in type. Ive bought a New Zealand model corolla 2009 , ill check if its the same as this, i hope not.
@waqarqadeer52172 жыл бұрын
I watched this video just because it was so satisfying to watch it 😁
@jonathanratliff47802 жыл бұрын
Great video so helpful with great info Petr!!
@Prostopyotr4 ай бұрын
That Polish accent 🥹 reminds me of my grandpa
@davea50172 жыл бұрын
Sir, where are you located? I have a 2007 tundra with 4.7. It is in need of water pump and timing belt kit.
@robertmassucci1 Жыл бұрын
you sound just like the guy that built the underground lab in breaking bad. Werner Zeigler
@rayemanuel74602 жыл бұрын
Inflation is so high now that I buy 2-ply toilet paper and then separate it into 1-ply. LOL.
@ricepony332 жыл бұрын
7:55 Bless you!
@MrCROBosanceros2 жыл бұрын
13:40, A few years ago I found a great Cleaner and Degreaser I like to use on plastic and rubber parts like engine cover, engine oil filler cap, brake fluid cap, engine air filter cover and other greasy automotive parts and tools. It is a WD-40 Specialist Cleaner & Degreaser. It is safe for use on aluminium, chrome, glass, plastic, rubber, stainless steel, leather, paint and much more. It is water-based biodegradable.
@billyrayvalentine52202 жыл бұрын
Nice job sir 👍🏻. Btw, next empty bottle of washer fluid, save the cap as it will fit on the drain neck of your oil catch pan. Used it on mine, same one. 😁
@ega01172 жыл бұрын
Do you still Subaru cars????
@michaeleilkamerer2098 Жыл бұрын
Sir,you are brilliant.Thanks for thoroughly showing us how the job must be done.Michael Einkamerer.
@davidelizabeth49332 жыл бұрын
Always better than Oil Stop. ❤❤❤
@Hernsama2 жыл бұрын
Blue crush washers are no longer being used. They switched to a graphite color one.
@joshhemingway72942 жыл бұрын
Hmm wired cuz a month ago, I bought some and they were still the blue ones
@florianwirtz63518 ай бұрын
Neat Guy
@superseries70072 жыл бұрын
Just get the ASSENMACHER TOY 640 TOYOTA LEXUS 64 MM 14 FLATS OIL FILTER SOCKET and be done with it.
@sophaman91932 жыл бұрын
Thanks for sharing your video where are your place in Canada 🇨🇦 or in the USA 🇺🇸 take care bye from milton Ontario Canada 🇨🇦
@johnlacroix16392 жыл бұрын
WOW very interesting super kool ,1st class great info.,, AAAAAAAAAAA++++++++++++ again great video I liked it a lot ,keep up the great work.
@rodicatudorache30712 жыл бұрын
Eneos oil
@kadhmkazem55866 ай бұрын
❤❤❤❤
@rodicatudorache30712 жыл бұрын
Eneos oul!
@captainamericaamerica80902 жыл бұрын
Change the air filter and cabin air filter too. 😊😀
@surf60092 жыл бұрын
I just purchased a 2010 Carrola from a dealership, and the air filter was very bad. Watching this great video, as it's my first Toyota, and ya things are so different. Got to purchase a T wrench for sure.
@teddypark98322 жыл бұрын
A gorilla tightened that oil filter housing. 25nm is 18.4 ft-lbs
@njsongwriter2 жыл бұрын
Next time I change our oil I'm switching from the blue crush washers to s copper crush washer. Those blue ones are coming apart with part of it sticking to the oil pan and part of it sticking to the drainplug and I have to scrape it off both surfaces.
@SaltGrains_Fready Жыл бұрын
The camera depth of field at 8:40 has everything behind you in clear focus when you are showing the filter and O Ring because the focus is setting on the distance back there where there is not any motion of objects. That leaves you and the item we need to look at in a blur. Manually setting it to close range will overcome this.
@tochukwuemmanuel40079 ай бұрын
The filter I bought came with O ring and one little ring. What is the little ring for?
@kj33132 жыл бұрын
I have a 2015 Corolla with the same oil filter and I hate that filter the first time I did the oil who ever put the filter on last over tighten it and it was a pain to get off and the cap was out of shape so I bought oem parts from a 2019 Corolla to converter it over to a good old canister style so much better now hahaha
@LAactor2 жыл бұрын
Thank you for showing the maintenance page at 0:25 to correct some people who like to argue online about correct procedures. Armchair mechanics think they know everything after watching some videos and guessing the rest of the answer
@surf60092 жыл бұрын
Thanks for the video. I recently purchased a 2010 tc s. Going to have to get the fiter wrench. And sure would be nice to have a fancy funnel. I bought Castrol, high mileage synthetic, 0-20 .a Wix brand oil filter.
@robertmassucci1 Жыл бұрын
you have nice way about you. I like the details you mention. great video.
@jamessena1410 Жыл бұрын
I wish I am back home permanently in California so I can visit your shop for car services! Keep up the good videos
@that80srat9 ай бұрын
Incredible video. Thank you!
@Bwh-rm3py2 жыл бұрын
Oil filters are always overtightened for some reason.
@jtaylorjt92 жыл бұрын
How to change cabin air filter on 2002 sequoia
@shachardamari7550 Жыл бұрын
Thanks for the professional video clip!
@punzalanbenedick8423 Жыл бұрын
How many mm is your oil filter wrench?
@paulodisano5022 жыл бұрын
Great service, Peter. Ciao my friend.🇨🇦🇺🇸
@mehranaliakbari49432 жыл бұрын
Mate, thank you for the generosity of your spirit! Wonderful video. All the best.
@stendecstretcher56782 жыл бұрын
Thankyou once again. I have learned a lot from you.
@FarahmandMirza11 ай бұрын
Thanks man, I just saw this to help myself with my first old change. You saved me 120$ today😅
@raiderman28 Жыл бұрын
good job
@stephenhuber12192 жыл бұрын
Where is your shop?
@luisdorta9780 Жыл бұрын
👌✌️👏👏👏👏👏 thanks!!!
@toycoma982 жыл бұрын
Use a socket for the filter wrench, a coworker borrowed mine and returned it destroyed.
@jeyarajsan16122 жыл бұрын
Thanks 👍👍👍👍👍👍👍
@MotorDrives64922 жыл бұрын
What happened to the high quality parts?
@LAactor2 жыл бұрын
If customer brings, use.
@captainamericaamerica80902 жыл бұрын
FILTER LOOKED GOOD. OIL IS FULL SYTHN. SO IT'S EXCELLENT. I'D HAVE CHANGED THE AIR AND A.C FILTERS TOO
@MotorDrives64922 жыл бұрын
@@captainamericaamerica8090 Well he used to use Toyota Genuine filter and Toyota Genuine Motor Oil (TGMO) and now he uses some third-party filter and Costco oil
@johncasserly45 Жыл бұрын
Thank you
@jessebuenrostro20802 жыл бұрын
I have a 2007 Toyota Camry LE 2.4L . It currently has 149,266 miles on it. It always had oil changes on time with conventional oil. My question is, I'm thinking of using 5w-20 full synthetic so do you think I should use that or keep using conventional especially with the milage on the car .. Thanks
@rightlanehog31512 жыл бұрын
Synthetic is better for new or old cars.
@SE45CX2 жыл бұрын
When your owners manual states it can take 5w-20 for the temperatures in your area you sure can try synthetic as well.
@stephengrijalva88542 жыл бұрын
Great video
@rightlanehog31512 жыл бұрын
👍
@cediepurificacion84802 жыл бұрын
Does the o ring comes with the filter?
@shachardamari7550 Жыл бұрын
of course
@soldiersvejk20532 жыл бұрын
Corolla has a 2.4L engine? That is insane!
@BenJammin4272 жыл бұрын
It’s one of Toyota’s few poorly designed engines. Burns oil like crazy.
@TwilightZoneX2 жыл бұрын
👍👍
@damon3238 ай бұрын
What filter wrench is that??
@Miguel.Rosado72242 жыл бұрын
Thanks for the video. For future DIY, that oil filter housing has an oil drain plastic tool that comes with the oil filter and a small gasket that attaches to the drain channel and then the drain screw. And it seems that the owner of this Corolla has lost or miss placed. Take care.
@mannys91302 жыл бұрын
My Corolla doesn't have the filter housing cap drain nipple. I don't think the 2ZR-FE came with one of those like some other Toyota cartridge filters did. The 2ZR-FE cartridge is horizontal as you can see. The cap has deep flats cut into the threads which align with the same cuts into the housing. When you loosen the cap and unscrew it, you just unscrew it barely all the way, and align the 2 flat spots. The oil drains out through those flat spots right down into the drain pan. Once the cartridge housing has been drained through those flats, you can unscrew the cap the rest of the way and there will be 0 leftover oil to splash and make a mess. The plastic drain thing you're talking about is for cartridges that are vertical, since this flat spot method won't work. The drain tap drains the cap out cleanly. Check out the 2ZR-FE cap to see those flat spots I'm referring to. 😎👍 My 2012 Corolla is very simple to drain because of them.
@Miguel.Rosado72242 жыл бұрын
@@mannys9130 my 2009 Corolla 1.8, my 2017 4RUNNER 4.0 and my wife’s 2015 RAV4 all of them have the oil filter housing including the oil drain nipple. Yes the oil change without the housing it’s easier. I agree.
@CrowT2 жыл бұрын
No it does not. The filter housing that is horizontal like this doesn't come with it. The canister would not even drain if it had one. Only Toyota filter housings that are placed vertically have them. Edit: the comment above addressed your comment already🤷♂️
@kerry_runs2 жыл бұрын
@@Miguel.Rosado7224 my rav4 has this housing, it's so dumb. My corolla has the screw type which is way better.
@flucas65952 жыл бұрын
Can't understand a word you saying. And PLEASE show what oil brand you using to give people tips what oil brand they should recommend using.