LIMP MODE ?? P2445 : How to remove / replace secondary Air Injection Pumps
Пікірлер: 54
@tierneyc243 күн бұрын
The pumps are 12 volt DC so you can also test the pumps by making yourself two jumper wires to run from your battery. Disconnect the cable connection to the pump and make note of size terminals. Get yourself the correct terminal connectors to attach to the pump terminals so that they don't touch each other. Take the other end of your jumper cable and touch one to your battery + post and then shortly test to - post of your battery. Just for a second or two to do a bump test. I had one pump that would spin but the other did not so I have the choice to order only 1 pump before tearing into it. Wiring from the pumps: Red is hot and black is ground.
@paulraley19782 жыл бұрын
Your a life saver with your explaining the wire location
@ruinerfixxxer2 жыл бұрын
Awesome. You just saved me 2000$ the dealership wanted to do this job.
@seanperdue2322 жыл бұрын
Good info. Thanks for taking the time to edit and post the video. 👍😁
@null0464 ай бұрын
I replaced both of mine in a 2007 tundra. Also bought the update breather neck to avoid the water being sucked into them again. Replace both and clean them if they aren't cracked, maybe have them as spares.
@TrueStrategicEyes2 жыл бұрын
This is very helpful. Thanks you so much
@csclimber667211 ай бұрын
Helped me big time. Thanks !
@brianmcarthur7423 Жыл бұрын
Great explanation. Thank you!
@JohnWaid6Plus2 жыл бұрын
Thank you for this video it will help me I gotta change mine now
@silverstonespov52912 жыл бұрын
You are welcome, good luck. Thanks for Subs to my channel
@txsviking Жыл бұрын
Is there anything that can be done to prevent water from getting into the inlet tubes? Like after-market tubes?
@sladewehner8 ай бұрын
Thank you!
@DannyGutierrez-pv2os3 ай бұрын
Good job my amigo look my toyota tundra have the some problem i need to fix it im going to just like how you did in this toyota tundra cuz my is not running goog when im driving on the free way my friend but thanks you for this video amigo im going to waiting for the next video ok bro 👍
@dougsanders3579 Жыл бұрын
Thank you Sir
@6xcchamber9713 ай бұрын
Excellent!!!!!
@joerichardcycles692 ай бұрын
Thanx for the great info. These used to be under the intake . . How many hours should I charge? And also, did you replace the duel check valve? Thanx again in advance!
@baa8002 жыл бұрын
I was searching and searching for a way to to determine which pump is which. Thank you! I owe you a beer friend!
@silverstonespov52912 жыл бұрын
I'm glad my video can help, thanks
@baa8002 жыл бұрын
The check engine light came back on, this morning. I’ll have to check what happened.
@Casinolife072 жыл бұрын
My friend thank you for the video, I bought 2 pumps and would it matter if I accidently plugged for example bank 1 into the bank 2 harness they look the same?
@silverstonespov52912 жыл бұрын
Depend on how the system work, computer maybe turn on only the bank(s) that need air injet into the exhaust. If it turn on the wrong pump then computer will set the Fault codes and turn check engine light on. If after many km of driving both in the city and hi way with no engine light on, you are good
@Casinolife072 жыл бұрын
thank you for video, question: if by accidently plugged bank 2 to bank 1 or bank 1 to bank 2 will it matter? I bought both new pumps and they both look the same, the reason I ask is because i installed both and erased the check engine code but after a day of driving it came back on and truck went to limp mode.
@silverstonespov52912 жыл бұрын
Yes, PCM turn on each pump separately depend on which bank need air and need more air. That is why they came with 2 pumps .So, switch the pump connectors back, clear the codes and try it, good luck
@VicksWander2 жыл бұрын
Nice
@alialsigar6000 Жыл бұрын
Great Video!, I have a 2012 Tundra, V6 and had air injection system code P2443, I did replace the air pump with new OEM air pump and new valve for passenger side, I did double check all connections are good, but I still see the engine light, I reset it but still come out, I noticed the pump not making sound when I have the switch on, any ideas why this happening , is there a fuse or relay need to be checked ? thank you
@silverstonespov5291 Жыл бұрын
Sorry for late reply, there is no fuse or relay for this 2 pump, it control by modules for each air pump, both module are small(8 wire plug) both module at left rear of engine compt according to the wiring diagram
@KeepatIT69 Жыл бұрын
Thanks for your video. I have a 2009 4.7 and have replace one pump that’s on the right side where would I find the other pump? It’s a 2009 tundra 4.7 regular cab.
@silverstonespov5291 Жыл бұрын
It's should be at the same location unless it is had only one pump. I have to check the manual
@KeepatIT69 Жыл бұрын
@@silverstonespov5291 I only saw one but would like to verify. Thank you in advance.
@silverstonespov5291 Жыл бұрын
It’s has 2 pump, the right front of engine it bank 2, bank 1 air pump it at top of engine. That is base on the wiring diagram
@KeepatIT69 Жыл бұрын
It must be under the cover because not visible to me. Thank you very much!
@origpepper12 жыл бұрын
I replaced both air pumps. Checked first to make sure they were good. I get a p2445 code saying they are stuck off . Is there a fuse, link or relay that needs to be replaced, if so where is it?
@silverstonespov52912 жыл бұрын
I have to check the wiring diagram again to see. I didn't have to replaced any fuse or relay on that Truck
@Natebawl2 жыл бұрын
Why do some 5.7L models have the pumps behind the intake manifold close to the firewall??
@silverstonespov52912 жыл бұрын
Depend on the model year they mount the pumps at different location
@KeepatIT69 Жыл бұрын
Found out that if you open them up, you can actually clean them and they will work again.
@silverstonespov5291 Жыл бұрын
Yes, sometime it just need to be clean và especially for our own vehicle.
@mamawoodrow2 жыл бұрын
I replaced both of the pumps but it is still going into limp mode what else could it be
@silverstonespov52912 жыл бұрын
Check the Wirings, Fuses that can cause the Pumps not working. Did it still have the same codes?
@etechm87 Жыл бұрын
muchas gracias where can i get the pump
@silverstonespov5291 Жыл бұрын
Dealership is better but you can get them from NAPA or Auto value, Canadian Tire
@joeln1636 Жыл бұрын
This fix the traccion control lights
@carlostreadwell45652 жыл бұрын
All I did was check both of them the one that didn't work was bank 1
@chaldoboy100010 ай бұрын
Are they both pump are the same bank 1 & bank 2 ?
@silverstonespov529110 ай бұрын
Yes,Pump are the same but air hoses and wiring different
@chaldoboy100010 ай бұрын
@@silverstonespov5291 thank you .. can you share then link for these pump please
@silverstonespov529110 ай бұрын
@@chaldoboy1000 sorry I don’t have other link, it in the shop manual and I can’t
@leocortes30622 жыл бұрын
My toyota cranks but don't start, my friend connects something to the computer and air pump and the air injection come out, you think that's the problem? Why don't start.
@silverstonespov52912 жыл бұрын
Air Pumps work or not have nothing to do with the NO Start, you have other issues. scan it to see what code and go from there
@leocortes30622 жыл бұрын
@@silverstonespov5291 thank you.
@aal-bakri31929 ай бұрын
Hi thank you for your video Please i need to contact with you .
@silverstonespov52919 ай бұрын
facebook.com/thuan.danh.735944?mibextid=LQQJ4d
@gevang63462 жыл бұрын
The inlet tube is the reason why the water got into the pumps. It was a poor design by Toyota. I just changed everything and it costed me an arm and a leg.
@J727MONEY6 ай бұрын
Why not follow the air tubing and see if it goes to the side of the engine where cylinder one is where it's at the side of the engine where bank bank 2 is where cylinder 2 is just follow the air tubing an that should tell u what bank is which