2015 Ram Hemi, I replaced my sensor because of P018C code at 58K miles(I believe to be original sensor). Bought sensor from Amazon(with fuel line tool), a week for delivery. My ECO light, and remote start would not work with this failure. Engine ran okay. Took an hour to change sensor. Hardest part is climbing on top of engine to reach sensor. After replacement, I reset the code with my "Foxwell" reader, and everything is good to go! Thanks for video! Good job. Dale.
@elizirk43765 жыл бұрын
Mine came on last week 2016 35,000 miles they should replace them for free. I bought this low mile truck so I didn't have to spend time working on it, now I work on it and make payments. Thanks for the useful information.
@isaacchavarria14665 жыл бұрын
I had code P018C and replaced the fuel pressure sensor and it fixed the problem. I spent $115 including buying the fuel line remover tool which is a lot better than using a screwdriver. Dealership wanted to charge 150 just for a diagnostic even though i told them what the issue was. Save your money and do it yourself. I saved myself 300 dollars and if you have the fuel line remover tool it only takes about 30 minutes if that to do on your own.
@Handmantoot4 жыл бұрын
"$300 at the shop to get it done" Midas tried charging me $300 for the part! I bought it off Amazon from Mopar for $50! Thanks for the awesome video! saved me like $500!!
@bigsmitty3 жыл бұрын
First of all, thank you for having a good video for this. This is the ONLY video like this I could find. Secondly, I recommend going and buying the fuel line tool to remove the bottom portion. Don't want to mess up the clip with a screwdriver. It cost me $5 at Advanced Auto Parts. Definitely worth it! Thanks for saving me a lot of money by not having to take it to a shop!
@angelabarker13514 жыл бұрын
Thank you! I was able to replace the sensor on my own. You explained it so well. Saved us about $300.
@williamremington67132 жыл бұрын
took 30 mins on the dot, had the fuel line tool, and a step stool. 2015 Ram Hemi. thanks much
@Monsiemage5 жыл бұрын
This has to be the weirdest sensor issue I have ever saw, My light kicked on around 50k miles "Now has 76k" and I was having zero problems driving so about 6 months later my dad had one of those cheap cell phone app code scanners and it showed "Improper fuel air ratio replace MaP sensor" Well for 9 dollars I didn't argue but my problem still existed. Today I finally went to autozone, and was lucky enough to have the store manager scan my truck, and it showed on his code reader "Bad Fuel Pressure sensor/ Improper fuel air ratio" He told me he had never heard of that going bad so early, but this video has convinced me otherwise. My truck still kicks into eco mode, however it doesn't show ECO at the top of the monitor screen "Same issue you had" I'll be buying a new one tomorrow good to see that it's very easy to access now days, guess they learned their lesson, it was a pain when they had the whole assembly attached to the fuel pump above the gas tank.
@mikecioka11805 жыл бұрын
This is exactly the problem that I have with only 67k km on it. I when to the dealer and their mechanic said that the sensor was bad so together with taxes, labor and part 325 $ this should become a recall, how can it be bad so early?
@Monsiemage5 жыл бұрын
@@mikecioka1180 Sometimes companies get get away with it. My girlfriends Ford Fiesta also has a "universal problem" The cooling fans go out on ALL of them, at a low mileage also. It's better than Vortek getting away with their engines frying the cylinder walls 07-14 though, some of those engines barely made it 100k.
@transmitterguy4785 жыл бұрын
I just replaced mine today. The only issues I had was the bottom connector clips to the lower line. Just un clip it and pull it toward you. It's a safety to keep the connection secure. I used a line tool and It pulled the sensor end right out. Then I did the top red connector, both sides of it unlatch after you unlatch the red door part, then the red part pushes through to let the hose come out. Then I disconnected the power to the sensor, the gray part slides away from the sensor then you squeeze where the gray piece was and wiggle and it should come apart. Caution: my green "o"ring seal inside the connector, was pulled up, with the other piece, an the purple part was inside the sensor housing and when i went to put the old sensor on the bench, the purple part fell on the floor. It goes in the plug on the vehicle and the green "o": ring slides down over it. Then plug it onto the new sensor after you install it..
@pantallicera9 ай бұрын
Thanks for the tutorial, about to change mine out. Noticed the package said Panama City.. I used to live there 10 yrs ago, still visit friends when we can. Matter fact my profile pic is my wife and I during Mardi Gras in St Andrews lol
@pierrots82173 жыл бұрын
Always use a disconnecting tool for the line, you ever screw those tabs you're in for a surprise!!! Replacing that other line ain't a treat... Use the right tools for the job, it's cheap
@charlie23804 жыл бұрын
Thanks for the video, just swapped out my son’s and the only difference was we didn’t have to remove the tube closer to the firewall. The new connector had a connection by the sensor. 2013 Ram 1500 Hemi 5.7
@scottf.38085 жыл бұрын
Nice DIY fix as hopefully that cures the ecomode....Good stuff....
@johndurando4 жыл бұрын
Thanks man I just changed mine on my 2016. got it for $70 at the dealer only took a few minutes to change thanks to your video
@NorthFloridaOutdoorsman4 жыл бұрын
Glad to help , thanks for watching
@julianpalomo51124 жыл бұрын
What was your error code?
@NorthFloridaOutdoorsman4 жыл бұрын
I can remember, but wen replaced my CEL went off
@noelgonzalez95494 жыл бұрын
@@NorthFloridaOutdoorsman P018D? Was that the code? I just hooked up a scanner to my Ram and that's what came up. Just wondering if that's the same one you got.
@offroad81454 жыл бұрын
Noel Gonzalez hey man I have the same code on my 2015, did you end up doing this, if so did it fix the problem?
@nhlfnigel5 жыл бұрын
Just subscribed. Am a N FL native and a Mopar/Jeep guy. Nothing like a Hemi with cast iron block and heads. Keep the local color coming!
@NorthFloridaOutdoorsman5 жыл бұрын
Appreciate all the support, and will do
@chewiemac19742 жыл бұрын
DUUUUUUUDE!!!! Great video!!!! Excellent step by step. I DID buy and use a disconnect tool for the gas line. I’d add two things though. 1. My system didn’t depressurize as much as your did so I had a bunch gas spray out. I had to make sure that the negative battery post was covered with a rag to keep the cable from accidentally touch it and sparking off the fumes. 2. Have a step stool handy! I’m 6’5” and couldn’t reach without one! 😂 Thank you again for this!!!!
@tracykeller32773 жыл бұрын
I did this in about 35 minutes. I had so much trouble with all of the connectors, even the fuel line with a fuel disconnect tool. Just a tip, once I got up on top of the engine compartment and was able to pull the line upward and out rather than forward and out, it came out easily. Also it was 3/8" using a plastic disconnect set.
@tracykeller32773 жыл бұрын
Thanks for posting!
@tvgg5642Ай бұрын
Good video thanks but theres an easier way. Instead of doing your step of removing from what you called metal adapter 3:15 . just under the sensor is a clip thats taped remove tape and pop the 2 blue clips and pull the connection apart and bobs your uncle! Thanks again 👍
@alangarcia14962 күн бұрын
I appreciate this video - thank you!
@archersfriend5 жыл бұрын
Great to know. Dealer shops are WAY Over Priced. Surprised you got that good of a deal from their parts dept.
@jonpatterson56684 жыл бұрын
Great vid... my check engine just came on .. pulled the pressure sensor code ... the " eco" mode thing is a good tip I'll look to see if ots coming on, gas mileage dropped too
@ianmerino77064 жыл бұрын
It worked! Thanks for this video! Helped me a lot... saved hundreds 💰
@gerardomateo99722 жыл бұрын
Thanks for the video I just changed on my Dodge Ram but still with the same problem.
@bernie4723 жыл бұрын
Good video! Very informative. I also have that exact same shirt.
@craigbraley2 жыл бұрын
I have the same truck buying mine today.
@noelgonzalez95494 жыл бұрын
Good video! Had a pretty good amount of fuel come back up though - guess I had to de pressurize a little more but it wasn't too bad. Thanks for the video!!!👍
@laneymv4 жыл бұрын
Thanks for the video. I've had the part for over a year and been trying to determine how to get the line out where the clamp is at. I'm going to spend the $7 for a fuel line removal kit on Amazon. :-)
@jerryjohnsonii41815 жыл бұрын
MOPAR for life !!!!!!!! Have a Happy Easter Sir
@NorthFloridaOutdoorsman5 жыл бұрын
Thanks Jerry , happy Easter brother man .
@francisconegrete73483 жыл бұрын
Thanks bro!
@skylermock3 жыл бұрын
Just replaced the fuel pressure sensor took only 30 mins to do, replaced due to eco mode not coming in and a engine light fuel pump moduel not communicating, I had a code p062a and u0109 wich should indicate the fuel pump, which I went ahead and replaced the code was still on previously I had 2 mechanics shops go through the fuel pressure everything was fine and all the voltage and resistance and grounds were good, so I ended up replacing the fuel pump control moduel engine line gone but still pending codes, a day later engine light back on, soo I found this video and now decided to replace the fuel pressure sensor, no pending codes and engine light gone.... for now hopefully it was the problem!!
@mojo9696 Жыл бұрын
The area i needed to see you didn't video..hahaaha, you tried to explain it but really !...i think i can figure it out..
@billbkr32ify3 жыл бұрын
Your eco mode was working. Whenever the check engine light comes on the eco will not display but it is still working
@jakemason94363 жыл бұрын
Thanks. I think that sensor in the intake tube is IAT not MAF for our hemis.
@teachmetruth35397 ай бұрын
The one that came off anyway, is that where you put a hose into to drain bad gas ?
@timgiesin40254 жыл бұрын
I ordered my part through Amazon right after Christmas changed it when I got it and now the lights back on so now I'm ordering it from the Dealer and going to install factory part hopefully that will fix it and that it's not something else causing the problem
@robgreen90702 жыл бұрын
Thank you so much for the video… I would not have guessed to remove the gas cap to depressurize, or the fuse. Thank you for taking your time out to show us… By the way did the check engine light ever clear?
@NorthFloridaOutdoorsman2 жыл бұрын
It did , still goin good . 👍
@ultimatebjj2 жыл бұрын
@@NorthFloridaOutdoorsman How long did it take to reset. I replaced my sensor earlier today and the check engine light remained on also. Thanks for the video tutorial, it helped a lot.
@NorthFloridaOutdoorsman2 жыл бұрын
Discount the battery for a few mins and reconnect and try that
@ultimatebjj2 жыл бұрын
@@NorthFloridaOutdoorsman Thanks for the fast reply.
@rubenherrera92872 жыл бұрын
@@NorthFloridaOutdoorsman when I connect the battery it sparks, will it be the sensor?
@karenderuwe91343 ай бұрын
I have a 2017 ram 1500,with a 5.7 hemi the message on my dash came up today "fuel sensor failure " fuel gage went to empty engine light came on but truck ran fine .I changed out the fuel sensor but fuel gage still reads empty what now?
@haroldbirge68812 жыл бұрын
I have a 2019 classic my light just came on the code reads the same for that part did your engine light clear? 🤔🍀
@NorthFloridaOutdoorsman2 жыл бұрын
It did, some times you have to reset it or disconnect the battery for about 30 mins
@haroldbirge68812 жыл бұрын
@@NorthFloridaOutdoorsman I just did and it cleared 🍀hopefully it was just a glitch get R done😎✌️
@ThecrazyScotsman5 жыл бұрын
Looked like you did this on side of road lol hopefully all ok now good how to Brother!
@NorthFloridaOutdoorsman5 жыл бұрын
At my family's house , to be honest you could probably do it the the parking lot of a auto parts place , they charge 300+ to do this too
@fredrickchrisco68919 ай бұрын
THANKS, GOOD JOD
@FloridaRains4 жыл бұрын
What were your symptoms before it went out , I’ve chased a problem where my ram gets up to 50 ish mph then drops to 1.5k and likes to surge and have a tough time getting up, when I step on it it ramps up to 2k but nothing between 1.5 and 2k
@tinkthemadscientist26422 жыл бұрын
ECO mode is what’s prematurely destroying the cam and lifters in the HEMI engines and the best thing you can do for your engine is turn the ECO mode off by purchasing a programmer that will allow this to be done or put the truck in 8th gear by using the shifter on the steering wheel. It will prolong the life of yourHEMI.
@Shiftready Жыл бұрын
Thank you so much!
@Fernie12243 жыл бұрын
Can someone tell me what the issues are before replacing this sensor? Mine has been acting up every now and then where it’ll crank but won’t turn over. I have no check engine light or any codes so I’m kinda stuck guessing what could be causing this.
@matthewskinner1315 Жыл бұрын
Did you figure it out long shot since this was 2 years ago got a p025a code for mine mine will crank and start sometimes then other times it’ll crank and not start try again and I’ll have to tap the gas to get it to start
@Fernie1224 Жыл бұрын
@@matthewskinner1315 I don’t know for sure if I fixed the issue but I looked in to the fuel pump relay and found out that they have an issue where they don’t kick on so I found a fuel pump relay bypass and it’s been working fine since. If I unplug the bypass then I start having issues again.
@matthewskinner1315 Жыл бұрын
@@Fernie1224 what year do you got mines a 19
@neilmulvihill25943 жыл бұрын
Did anyone else not have that safety latch for the fuel line that he placed on? If not, where can this be found aftermarket? I’m not finding any on the sites I’ve checked.
@dirtymike26463 жыл бұрын
I have a 2013 ram mark me code p018D pressure fuel sensor. I already replaced it but the light is still on
@rubenherrera92872 жыл бұрын
when I connect the battery it sparks, will it be the sensor?
@eduardocalzadilla1088 Жыл бұрын
good video❤
@mateozambrano47023 ай бұрын
Super 👌 esacto eso me ase la mía yase que es el sensor de gas 😅😮😮😮😮
@rickvega99435 жыл бұрын
My 2015 engine light went on yesterday my scanner shows P025B fuel pump module control. I have only 33,000 miles. Truck runs and starts perfect. Dodge dealers are telling me that I need a new fuel pump..How can I need a fuel pump when my truck is running perfect ?? Engine light stays on. Do you know anything about this ? thank u
@NorthFloridaOutdoorsman5 жыл бұрын
I would think it's still under warranty, does it go into eco mode while driving down hwy ?
@FloridaRains4 жыл бұрын
I’m probably late but on Amazon’s they make a bypass for your fuel pump relay , since it’s soldered into the board you need to bypass it with the rear cig lighter fuse . Should fix ur problem and save you a big paycheck
@aldogonzalez83634 жыл бұрын
The check engine light came off today and it's the fuel pressure sensor....just wondering if this fixed yours?
@fiddlinjazz4 жыл бұрын
What is the reason for changing the fuel pressure sensor?
@starmc263 жыл бұрын
It causes a check engine light, will not go into eco mode, and disables remote start.
@wadetaylor31954 жыл бұрын
Has anybody tried a fuel pressure test on this generation Ram? No schrader valve. I’m thinking this might be the location to tap into the fuel line ??
@TSCOTT-oz5vy4 жыл бұрын
Finally replaced my sensor to a 2016 RAM. Light came on a day ago. Look like the circuit board on my old sensor was burnt out. Paid $90 at dealership for part and a mechanic put it on for me. The mechanic never removed a K5 nor undo the negative terminal off battery. When he replaced the fuel pressure sensor the mechanic had to hook up his hand held system to reset the check engine light. Paid $45 to my mechanic for the labor. For $135 it worth it to have that dern engine light off. Seems like my RAM sound better and run better also. Ram not sick no mo. FYI...stop using that ratchet ass gas. Lol😂
@johncurley70824 жыл бұрын
Do you remember the fault code you where getting?
@moltoyexpresscorp2084 Жыл бұрын
After replacing that sensor check engine still there it will automatically disappear or need to delete it by scanner? Thx
@NorthFloridaOutdoorsman Жыл бұрын
After I plugged the battery back up it went away
@moltoyexpresscorp2084 Жыл бұрын
@@NorthFloridaOutdoorsman i replaced that sensor with unplugged battery, but after battery putting battery back check engine light still there, delete it with scanner, run engine cycle ignition and check engine light back again🤷♂️
@NorthFloridaOutdoorsman Жыл бұрын
Sometimes it takes up to 30 minutes for the cycle to complete itself before hooking the battery back up. Best thing to do is hook up to the scanner and make sure that is your problem and check the code if it’s a code for the sensor, then delete it and see if he comes back.
@JBWHITEGT4 жыл бұрын
Does anyone know if this will resolve random start up stutter on the 5.7 Hemis?
@jeangonzalez73734 жыл бұрын
Was the code p018c ?
@C3ZaR915 жыл бұрын
Did the check engine light come off on its own after a while?
@NorthFloridaOutdoorsman5 жыл бұрын
I unplugged my battery and reset everything, but it never came back on. Its was the problem and this fixed it
@harmontodd4 жыл бұрын
Nice video! Do you recall the OBD2 code you were getting? I got a P018C yesterday, and it looks to be pointing the Fuel Pressure Sensor low reading. The truck shows no symptoms of trouble, took it on the interstate and hotdogged it... if there was a fuel delivery issue I couldn't feel it. Thinking the sensor is just bad.
@NorthFloridaOutdoorsman4 жыл бұрын
I dont , I didn't see or feel and issues either, just it would not go into eco mode
@harmontodd4 жыл бұрын
@@NorthFloridaOutdoorsman Bud, I can't thank you enough for this video. Just performed the exact repair on my 2016 and resolved the engine code (and ECO mode not showing up any more). Saved myself about $2,000 bucks based on ridiculous dealer quote. Of course you didn't mention you are probably 7 foot tall with a 13 foot wingspan.... holy crap was this stuff buried way back there! I'm 6 foot tall, and had a good step stool and was still struggling to reach everything! Anyway, thanks again!
@NorthFloridaOutdoorsman4 жыл бұрын
@@harmontodd yeah man glad I could help . Thats why I do it , some of my videos are for fun and get alot of negative comments but helping others make it worth doin . Thanks for watching and glad you got it fixed
@ryanrodriguez21394 жыл бұрын
What problems were you having with it prior to changing it that resulted in you getting another sensor? I have a 14 ram that never turns on the first time I have to crank it a few times. just finally want to pin point my problem been going on for about a year and a half now
@NorthFloridaOutdoorsman4 жыл бұрын
Wouldn't go into eco mode and had a engine light on dash
@haroldcasco3 жыл бұрын
Ram does not use a maf sensor but the one you disconnect was the intake temp sensor 😇
@NorthFloridaOutdoorsman3 жыл бұрын
Good to kno , im just a diy guy not a mechanic for sure , thanks for watching and for the comment
@shawnmiller9323 Жыл бұрын
How do you get the safety clip off on the bottom fuel line?
@NorthFloridaOutdoorsman Жыл бұрын
I used a flat head screwdriver, just got to play with it , I do believe they make a tool for it but not sure
@saintb15004 жыл бұрын
Can this code come out if ur girl forgets to put the gas cap on a drives for a few days... i was.going to just try unplug the fuels and baterry and see if it work again now with the gas cap on
@audieshirley45623 жыл бұрын
Did this fix your problem? I've got the same issue. Wife didn't tighten the gas cap now it's saying fuel sensor but I'm not sure this is what I need. Thanks
@saintb15003 жыл бұрын
Yes it did work
@kendrickroland79304 жыл бұрын
Hey did this fix your issue with the code? My light just came on today with the same code and I to have a 2015 ram 1500 with a 5.7L HEMI
@NorthFloridaOutdoorsman4 жыл бұрын
Yes it did , light gone and bow it goes into eco mode
@matthewschroeder7194 жыл бұрын
How long before the code cleared itself?
@matthewschroeder7194 жыл бұрын
Never mind...I read below where you said you had to disconnect the battery, that’s what I did and it cleared the code! Thanks for the video! By the way to all those folks out there the fuel line tool makes it much easier to Disconnect. Mine are plastic, assorted sizes.
@matth36375 жыл бұрын
Did that fix the issue mine is doing same thing as of last friday
@NorthFloridaOutdoorsman5 жыл бұрын
Sure did , light gone and now it goes into echo mode
@matth36375 жыл бұрын
@@NorthFloridaOutdoorsman sweet. Really had me worring just bought mine 4 months ao. Thanks for the vid man. About to go by my part
@NorthFloridaOutdoorsman5 жыл бұрын
Subscribe, more to come on my trk , thanks for watching
@nawafal-hommadi2693 жыл бұрын
I have p2016 problem but i don't know exactly where the error is, can you help me find out where the error is and how to fix 1500 RAM 2014
@NorthFloridaOutdoorsman3 жыл бұрын
Sorry man, not sure best thing to do is google it and read forums
@nawafal-hommadi2693 жыл бұрын
@@NorthFloridaOutdoorsman Thank you very much
@deadfluffy124 жыл бұрын
Going through this now. Stuck on trying to unplug the sensor cables with the purple tab. Any tips?
@NorthFloridaOutdoorsman4 жыл бұрын
I used a flat head and was gentle with them , took some time but I got them to come undone, hope you get it .
@deadfluffy124 жыл бұрын
North Florida Outdoorsman got it. Took way too long but didn’t know that gray clip came all the way out. Couldn’t find any videos showing or describing it and with a 6” lift it’s dam near impossible to get 2 hands back there to work.
@NorthFloridaOutdoorsman4 жыл бұрын
Good deal , sorry I didnt show that very well .
@deadfluffy124 жыл бұрын
No worries. Awesome video and much appreciated.
@TheAirfreshiner34 жыл бұрын
What was your original fault code?? I have P018C on 2015 Ram 1500. I think it’s the same problem....
@NorthFloridaOutdoorsman4 жыл бұрын
Not exactly sure, i forgot to write it down sorry. But that seems like it . Hope you get it figured out
@kingpin76735 жыл бұрын
👍👍👍
@TomBrewer-m6qАй бұрын
Do not follow the disconnect sequence!
@DanielGarcia-pf4sx4 жыл бұрын
Did you ever change the sensor on a 3.6 v6 engine?
@NorthFloridaOutdoorsman4 жыл бұрын
I haven't, iv just changed it on the v8 .
@bjacrp2 жыл бұрын
What’s your part number?
@fivestarhemi28773 жыл бұрын
What code was it showing? P025d??
@NorthFloridaOutdoorsman3 жыл бұрын
I forgot to right it down , but is said fuel pressure fault