2015-2017 Mustang GT Ford Performance Stage 3 Power Pack - Install & Dyno

Improve performance and horsepower in your 2015-2017 Mustang GT with this Ford Performance Intake and Calibration Power Pack 3! These calibrations feature exclusive Ford proprietary software and engineering backed by a Ford Performance warranty. This Power Pack includes a GT350 cold air intake, GT350 intake manifold, 87mm throttle body, and Ford calibrator. This kit increases performance by 37hp and 5 lbs/ft torque peak gains over stock to the flywheel. At 7,500 RPM they saw a spike of 60 horsepower on an engine dyno!
______________________________________________________
Stage 3 Power Pack: lmr.com/item/M...
GT350 Catback is no longer available and discontinued
Limited Warranty:
lmr.com/page/F...
______________________________________________________
Stock Dyno: 395HP/370TQ
Ford Performance GT350 Sport Catback Exhaust
Manual MT-82 (5th gear pull at 1:1)
3.73 Gears
93 Octane
19" Wheels
After Dyno: 432HP/380TQ +37HP/+10TQ
Ford Performance Stage 3 Power Pack
Ford Performance GT350 Sport Catback Exhaust
Manual MT-82 (5th gear pull at 1:1)
3.73 Gears
93 Octane
19" Wheels
Mustang Fitment: 2015-2017 GT w/ 5.0L
Item # M9452M8
MPN # M-9452-M8
______________________________________________________
KZbin: latemodelres.t...
Facebook: / latemodelresto
Instagram: / latemodelresto
TikTok: / latemodelresto
#LMR #Mustang #FordPerformance
______________________________________________________
Use of this video is subject to the terms as set forth in our LMR Install Video Disclaimer | lmr.com/page/l...

[@wclutch]

This video helped me a lot with the installation. Everything worked right away with my tune. I used a PMAS cold air and locked IMRC’s open so the routing was slightly different but it all worked.

[@patrickmartin2689]

i think I'll pay for the stage 3 kit and then pay an expert to put it on, watching this made my head hurt😆

[@charlesmeaux3954]

you seriously can't bolt on an intake manifold? You should not be driving.

[@patrickmartin2689]

@@charlesmeaux3954 17 other people disagreed...🤔🤔🤔 besides I personally don't have the patience for all that...😁😁😁✌✌✌

[@MrClews7]

Nothing wrong with being honest. I just did mines and I wish I would have had someone to.do it for me as I have so much to do.

[@MuahMan]

@@charlesmeaux3954 Looks pretty daunting if you haven't wrenched on cars that much.

[@mikehughes8023]

@@MuahMan It’s practically an easy job with a seasoned mechanic looking over your shoulder.

[@gcmfskg]

I think people are missing the point that this is to keep your warranty. Of course you can get more hp from any other tune but your fucked if anything happens. I order mine tomorrow ride it out until the warranty runs out and than hook a Paxton to it.

[@ImVaiiderr]

S550 Gainz how has it been so far?

[@triumph928]

+ S550 Gainz: Federal Trade Commission (FTC), the agency confirmed that “The Magnuson-Moss Warranty Act makes it illegal for companies to void your warranty or deny coverage under the warranty simply because you used an aftermarket part.”

[@joemont4796]

Just got mine installed and so happy with it amazing how much it woke up the car, the best part is that if I blow up the engine it's covered by the warranty

[@wazqii7191]

You took it to ford to install?

[@cbcg_187]

@@wazqii7191 I’m wondering the same thing I’m bout to do this to my 2017 gt mustang and need to know how much it cost

[@Ford_Raptor_R_720hp_V8]

*Look at the Wheel Horsepower Gain from 2000-3700 rpms, which is where you spend most of your time.* *+50whp at 2200 or 150whp to 200whp* *+45whp at 2500 or 170whp to 215whp* *+25whp at 3000 or 220whp to 245whp* *+15whp at 3500 or 265whp to 280whp* *472 peak BHP* *435 bhp stock*

[@Pheenix9900]

Gonna have me some fun when the 2018 version comes out.

[@Pheenix9900]

@Elliott Feaster Me?

[@Noneyurbusiness]

*Exactly most people ignore the gains under the curve and only focus on the peak gains*

[@freshdumbledore2198]

Man, some people cant read dyno sheets, it´s not always about the peak gains.... look at the great difference from HP an Torque from 2000rpm to 3000rpm (+50hp/30ftp) and once again at the huge difference starting at 4700rpm till the end. there is a difference of torque from 30 footpounds constant and 35whp at 6500rpm to a stock mustang. after 5000 rpm the voodoo bridge breaks the shit out of the car, especially after the point of 6700rpm. whp plus from 70hp and 50ftp. Halleluja! Thats definitly worth it and you keep your warranty and theres no bad tune on it, killing some carparts. With a deleted electronical speedlimiter you could hit in 5th gear 175 miles at 7500rpm not "just" 150. for a quick mile, it is also great thing, because you will hit 120 miles with no extra shift in 4th gear. In my opinion, this is a killer tune from ford performance, you will get a all new character out of the mustang.

[@P71ScrewHead]

i'm glad I'm not the only one to see this, you saved me the having to explain it, plus the new red line is 7,500rpm with no head work, now if I knew what the price was, but the labor Ford charges is what I don't like..lol but many shops charge a lot anyways so not bad going with Ford for the warranty..

[@awestner]

Thank you for a great installation video. I'm sure it saved me at least 3-4 hours of do-overs when I'll be attempting the task this weekend. I can't believe Ford didn't provide any documentation with the manifold; yet with a relatively simple Ford CAI purchase, they include a 15-page illustrated instruction manual.

[@DaBrute]

might as well put that money towards a supercharger

[@amnscottnn5481]

Superchargers cost around 5-6k and void the warranty. This is much less and does not void the warranty. So no, I'd rather not put that money towards a supercharger.

[@aj-wq4sn]

roush and their roush supercharger is partnered with ford performance and if installed by an authorized ford dealer that sells roush products it will not void warranty.

[@BluRadoZ71]

That doesnt include thousand plus for new wheels to grip better and other parts to handle the SC.

[@Spiritcr1jsher]

@@BluRadoZ71 not to mention more weight ..... probably another 100lbs when it's all said and done.

[@dunkindomnuts3900]

Ive been waiting for this video for a while thanks LMR. yeah only 37hp but look at the peak gains! The stock GT runs out of steam and puts out 360whp at factory redline of 6700, after the stage 3 power-pack its still pulling harder for another 700-800 rpm to 7500rpm and 410whp with no lift shifting. Thats a 60whp gain up top with stock driveability. This would make a massive impact on a roll race. And you keep your factory ford warranty for 2k, im sold. I have a 15 GT pp when I get my tax return you will get a call from me LMR.

[@latemodelrestoration]

Thank you for the great feedback! -Landan

[@stevewill1940]

we have found better power with porting the stock intake at the tb inlet and just cleaning the runners--along with tony gonyons dyno tunes I make 392 hp and 379 torque with small mods-in a 14 auto---when not spraying

[@hmackprotection1]

Late Model Restoration, read my comment I just posted. Thanks

[@NoBody-tz4fb]

Lol same, 7500 redline im sold.

[@jaironfuentes761]

Force Times Distance Equals ? Torque wer you

[@awhitness]

So stock tune with a catback is 395whp. Cold air intake and a tune would put you at 415whp. GT350 intake 430whp. So the intake is worth 15whp.

[@terminatorcoyote6319]

finally sure am glad you review the power pack 3

[@jarvisclark8195]

Wish you guys would deliver to Switzerland! Nice work!

[@SpyderRios]

I am pretty sure Ford's tune is pretty conservative. I don't doubt that a more aggressive tune would yield and extra 10 plus at the wheels. Great combo, the installation seems like it involves alot of steps though.

[@Four_Eyes]

Another great install vid. Similar to a 3-valve in a lot of ways, but looks like it requires about double the work due to so many "in-between" steps.

[@blade000007]

lots of work and money for 37hp!

[@mgerren88]

blade000007 this is basically to keep Warranty on car otherwise...too pricey

[@851995STARGATE]

blade000007 Look at the top end power its around 60 wheel more at above 7000 rpm so it is worth it. Also the tunes are pretty conservative it should make much more

[@brandontemples2105]

CENTENON you do know 17 year olds can drive by themselves

[@atvkid0805]

no doubt, save your pennies and get a forced induction setup

[@Ford_Raptor_R_720hp_V8]

atvkid0805 *Why would I want a 700hp Mustang?*

[@02468]

Love your videos Landan!

[@latemodelrestoration]

Thanks for the kudos brotha! -Landan

[@latemodelrestoration]

That was crazy! Glad you like em, Brandon! -Landan

[@jettjacobs33]

American Muscle claims 60hp gains at 7500. All dyno results i"ve seen have been around 40??

[@edwardaldahondo9987]

Great instructions. I was able to install everything without complications and this is coming from someone who has basic skills.

[@latemodelrestoration]

That is Great that the install had no issue. We appreciate your support. Thank you

[@331LX]

You do a good job on your tutorials. Keep it up!

[@latemodelrestoration]

Andrew, thanks for the kinds words! -Landan

[@smokeum12]

Late Model Restoration what does this pack raise the rev limiter too? Also is there an option to raise the speed limiter? thank you

[@gt8674]

Yo bro you gotta slow down when when giving instructions and installing parts dude you speaking and working faster then the car would run.

[@gorillazgarage7482]

LMR big question here.. I just ordered the gt350 throttle body, and I got the Blowfish adapter unit that’s used to install it to the stock manifold.. however, I’ve decided to get the 350 manifold and do it all at once.. so do I still need to use the blowfish adapter? If not, is it still an option for me to use it, and have it act as a spacer? Thank you so much.

[@axelsilvajr]

If you didnt get an answer yet, no you don't need the blowfish adapter and no you cant use it as it wouldnt be the same connections. When you use the blowfish adapter its connecting the 87mm tb to the stock manifold because the tb wont fit without it, but on the 350 manifold it is already fit to take the 350 tb and it would be technically useless and probably won't fit

[@technojesusentertainment]

stage 2 better deal less work. .

[@01gt46]

How is it possible that the HP and TQ crossed at 4750 and not 5250? I thought all cars cross at 5250...

[@marcus7998]

This kit is Awesome! The downside is Fords tune its absolutely WEAK ! Best mod i did was getting tuned by Lund it added the Power to this kit that Ford should of gave it.

[@vincentsoresi417]

What did you make with lunds tune ?

[@marcus7998]

@@vincentsoresi417 haven't hit the rollers yet. But i went from 13.01 to 11.9. Fords tune felt just like stock 100%.

[@number1pappy]

37 hp and 5 tq....thats it!!!....for 3000 dollars!!!!!!!!are you f...ing kidding me!!

[@TheWhiteCometOfZion]

Retired at 49 - It's $1800 online...

[@jrvbamafan1]

That's at the tire and you can get it for $1600-1800.....not sure where you got 3 grand from. That's about 50-55 bhp so that's not bad for that price. Nothing you can do for less that'll get you more, especially while keeping the warranty

[@azizatia6049]

Do this car come with the catalytic converters from factory? And do it still have it? Amazing results and a good video!

[@latemodelrestoration]

Yes, this car has catalytic converters from the factory, and yes, it still has them in place. Thanks for the great feedback! -Landan

[@travfdy]

What were the curve gains? I wanted to compare them to the numbers from your stage 2 video. Do we get those same lower end benefits with stage 3 that we get with stage 2, or is stage 3 only for the higher end with the lower end still feeling stock? Thanks.

[@latemodelrestoration]

The low-end torque curve of the stage 3 kit is less than that of the stage 2 kit. You are right, the stage 3 kit is engineered for top-end performance. -Landan

[@travfdy]

@@latemodelrestoration Thanks Landan. Do you know what the crank horsepower increases to after power pack 2?

[@latemodelrestoration]

Considering the 421RWHP from the stage 2 dyno, I would put the flywheel numbers around the 480-490HP mark with the stage 2 kit. -Landan

[@travfdy]

@@latemodelrestoration thanks bro

[@latemodelrestoration]

You're welcome! -Landan

[@240brah]

if you have 2k for the stage 3 kit and another 2k for the gt350 exhaust just laying around might aswell of added that money toward a real gt350 down payment lol

[@Texarmageddon]

A GT350 down payment?? Really??? You're talking about a 25k difference on average in pricing. That's enough to buy halfshafts capable of withstanding 1000HP.... A formidable clutch and trans, a forged short block and turbos/Supercharger.... You are talking about a full build here.

[@axebeard7677]

25k diff without dealer markup. one at my dealer was selling for 80,000. Thats x2 what my GT cost.

[@240brah]

Texarmageddon what i ment was if you have thousands of dollars to just throw away, you could probably afford a gt350.

[@johnalcala]

Nah hell no. That's why I earn money - to pay someone to do this for me. I'd fuck something up for sure 😂😆

[@mortenberg2897]

Definately too complex for a diy for me. You make it look easy 👍😎

[@latemodelrestoration]

Hello Morten Feel free to call me directly at 254-296-6556 if you have any other questions. Have a Great Day.

[@G4G3PLAYS]

I just installed this today on my 2016 mustang gt. I have very minimal mechanic experience so it took me about all day haha hardest part was the sound tube bolt and overall just leaning over the car for hours. Car now runs perfect! Sounds better. So responsive. JUST WANTS TO GO! Last intake had bad runners so it's nice to see the check engine light go away. Yeah the price is a little much but who cares. Gt350 parts make the gt happy. If you're new to this work just be patient. Watch this video and pause and replay parts as you go. Don't rush.

[@latemodelrestoration]

Thanks for the comment and for watching the video. We appreciate it! -Landan

[@asreneorlsd2814]

🤣😂😂😂 terrible power results for stage 3

[@devinwilliams9058]

I really need your help on this. Can you guys do a video on replacing the cooling temp sensor I feel like if you take the intake off you can reach it and change it from there I wanna say. If it’s possible could you guys do this. That would be highly appreciated. I’m new to the coyote platform.

[@latemodelrestoration]

Thanks for the comment. Unfortunately, we won't be able to just run out and shoot a video covering your concern. However, the sensor is located at the back of the passenger side cylinder head. Per the Ford workshop manual, it shows that only the intake manifold needs to be removed to replace the sensor. Hope this helps! -Landan

[@bugattirocksful]

I really want to do this but it seems like a ton of work. I am very mechanically inclined, but don't know if I would have the balls to do it myself. Got quoted $1500 for installation at my dealer and that isnt happening either. Is it worth it?

[@charlesmeaux3954]

its a 1 hour install!!! IF that is a "ton of work" you need to get a new hobby.

[@robbyboyles8351]

Only 37 more HP and only 5 moreFt pound of torque ??? You can gt more than that cheaper from a basic tune !!!!!

[@notsafeforchurch]

You won't get more than 37rwhp from a tune unless its an FlexFuel tune and you run E85, even then they'd be about even. Moreover, what of the people who've already tuned their vehicles? I have an intake, longtube headers, and Lund FlexFuel tune. I'll take another ~40rwhp ontop of that please!

[@cemsengul16]

At the risk of sounding stupid I have one question for you guys and wonder if anybody who has installed this kit can answer it for me. If you install the Ford Performance K&N cold air intake does the Ford dealership reoil the filter for you as you come by to do regular services? I know that you do not reoil it frequently but that is a serious fear of mine, applying the oil and fucking up sensors. I would pay the service or aftermarket area of a dealership to do that for me

[@keithdavis7661]

Ford didn't receive the bailout....that was GM, Chrysler.

[@uscfroadie]

Ford should offer this setup as an option for original purchase, not as an add on. The cost difference would be minimal...but then again, maybe this is the power gain the 2018 will have. Time will tell.

[@jackhammer4656]

Whole lotta jack for less than 40HP and almost nothing in torque! Long way to go to make it worth the money!

[@vxer1000]

Really? That's $50/HP which is half of the standard $100/HP.

[@chalada4787]

I really like the video but for stage 3 the power is too low

[@331Grabber]

It makes a bigger difference than just peak power. It also extends the usable power band by 500 RPM.

[@marcasswellbmd6922]

8:00 in and I am done.. This will never be done by me all for like 30 more horse power.. I will just save till I can get to National out in VA to do a stage 1 Whipple for me and call it a day.. I want 600/650 Reliable Pump 91/93 safe and as factory as possible power, I want it to run and look like it came from Ford that way...

[@latemodelrestoration]

To each their own. -Landan

[@marcasswellbmd6922]

@@latemodelrestoration No Offense meant at all.. I look forward to buying other things from you guys.. I am on a waiting list right now for GT350 style wheels and Nito tires. For my 17 GT.

[@latemodelrestoration]

@@marcasswellbmd6922 I didn't take offense at all. -Landan

[@marcasswellbmd6922]

@@latemodelrestoration Thanks Landon, I love what you guy's are doing and I've been looking at maybe doing the stage 2 kit... Air box and throttle body, ((But I see that the inlet on the stock 17 Intake is only like 80mm.. So that's the rub for me.. It seems a little off trying to put an 87mm throttle plate on an 80mm intake opening.. IDK..)) But I do hear that there is a real 20HP gain, No lift, which I will never use because it's something at my age I could never get used too. When I was a Kid 35 years ago.. Jesus.. Anyway, I tried power shifting and it felt so weird and I was never able to keep my right foot totally to the floor. It's like blinking to me, I can't control my right foot from lifting slightly.. LMAO!!! But then I hear there's way better throttle response. SO I don't know. I would have to take it to Ford and have them do it for me too, so there's another $700/$800 for install too, The price seems spot on fair for the stage 2 setup!! I guess I am still on the fence.

[@chuckvaldez4149]

Spend around $3500 at your local ford ripoff center to gain 37HP think not!!

[@antz19coyote73]

“ High Flow Paper filter” 😂

[@furrypancoacoanut]

Love the video, but it’s corrugated

[@xPULPxVELVETx]

If I tried this I would fuck up so hard lol

[@josecarby1290]

Can you take it to any ford, purchase the kit and have them install it? Also if I take them bbk headers can they install them aswell?

[@latemodelrestoration]

Jose - I would contact your local dealership first before assuming. Long tube headers are not supported within the Ford calibration. -Landan

[@rompn4x]

I was able to get 409hp 407tq to the tires in a 14' Camaro automatic with full exhaust, CAI and a 91 octane tune. The LS and Coyotes are tough to beat.

[@ryanb200]

Those numbers aren't too shabby. You need a cam to really wake up that LS though.

[@denzellpowell2774]

rompn4x Ls3 or L99? Ls3 is what you want

[@jaironfuentes761]

Denzell Powell akioras boy

[@IdontKnow-fd6rp]

That's it?

[@ryanbullock242]

I've run into a few problems with my 2019 GT essentially the GT 350 manifold does not have the same imrc plugs in the . There is only one blue plug and the two white plugs do not fit either. Also not sure what to do with the EVAP routing because things have changed since 2015 to 17 model you no longer unscrew the EVAP sensor and port and move it over I wish there was a video for 2019 install

[@WTF-ty7ep]

I have read that the factory is just as good as the gt350 intake manifold. There's nothing to gain.

[@ccmckernan]

so does the gt350 intake manifold add more power, revs, and area under the torque curve than the cobra jet and boss 302 manifolds?

[@latemodelrestoration]

Check out this article StangTV wrote covering the popular Coyote intake manifolds: www.stangtv.com/tech-stories/engine/coyote-intake-manifold-shootout-gt-gt350-boss-302-and-cobra-jet/ You'll notice the Cobra Jet and GT350 manifolds make similar power. -Landan

[@o0oVAUGHNo0o]

This was an amazing read, thanks for posting Landan! -Houston

[@dipolararc4848]

creating your very own Mach 1

[@rowinglove4ever]

stage 3 kit and the car still has the original exhaust?? decat this thing put new hight flow headers and have some nice gains...

[@XOLEX1]

Just installed the kit, car shows P2006 code what can that be? Tuned the car as well. Can it be the white wires in back of manifold?

[@MEsfits]

Do you have to install stage 1 and 2 before installing stage 3? And does stage 3 include 1 and 2 in it ?

[@latemodelrestoration]

No, you do not. Stage 3 does not include 1 or 2. -Landan

[@stephensilliman8692]

Kay MEsfits l

[@jermbarnett1]

How much did you notice on the mpg? Lose or gain? I read a intake shootout between the stock Coyote intake , bose302, gt350, Cobrajet intake. In the article they where upgrading 2014 gt and gained 2 mpg with the GT350. Curious if there was any significant change with the 2015 when upgrading to the GT350.

[@yellowdoghnut45]

that is entirely too many damn sensors

[@williamdelapena1121]

Also why is this one better than stage two🤔?

[@latemodelrestoration]

The manifold will offer much more benefits.

[@CompOstang50]

How does this kit respond to an e85 tune? I'm wondering, as e85 is plentiful in my area...and waaay cheaper than 92.

[@latemodelrestoration]

Hi Petty, Premium fuel, 91 octane or higher, is required when running this kit. If you have any other questions or concerns, please give us a call at 1-866-507-3786 or use the contact us link below to email our tech team. lmr.com/contact

[@AKAKILLINGKING]

remember this still doesn't have full exhaust & a proper tune. And even then full exhaust won't void your warranty but the tune might

[@AKAKILLINGKING]

And you can still put a better air filter, and weight reduction. You can easily put a Camaro SS & srt 392 to sleep while looking better and have the warranty! And instead of getting the performance pack upgrade you can just spend that money towards this and get a 477hp mustang with dealer warranty

[@RobertKohut]

Seems very similar to my Boss 302 intake manifold, 90 mm BBK throttle valve, Airaid CAI and SCT tune I put on my '13 GT. The Boss 302 intake looks better though! Will the '15+ cars take the parts I put on my '13? If so what might be the price difference?

[@nvhsaccel]

Robert Kohut the boss intake manifold will not allow the 15+ hood to shut. It would fit the motor though.

[@RobertKohut]

nvhsaccel Thanks!

[@lencac7952]

There is something off on the stock reading as the HP and TQ do not intersect at 5252 rpm. Never seen a dyno graph that was not intersected at 5252 rpm. The 2nd graph is correct by comparison. Interesting don't you think?

[@latemodelrestoration]

You can scale the graph in the dyno software to where the axis are "locked", thus shifting the intersect point of the horsepower and torque. This doesn't alter the results, but it change the look of the graph for a different visual of the horsepower and torque curve. For the stock run, we accidently "locked" the axis in the software. Thanks for the comment. -Landan

[@lencac7952]

@@latemodelrestoration Hi Landan: Hilarious! This is a 6 years old video and you still replied to me. That's awesome! Nice job. I thought I was the only one who did that. Didn't know the graph could be manipulated like that. I just bought a complete Gen 3 Coyote from Summit. I also have a cherry, 03 Marauder. What do you suppose could happen?

[@latemodelrestoration]

@@lencac7952 I try to respond to every comment that comes through. You could have bought that Gen 3 engine from us! :) Sounds like you have a fun project! -Landan

[@lencac7952]

@@latemodelrestoration Hey Landan: So what would it cost from you. Complete Gen 3 Coyote with flex plate, engine and trans harness?

[@latemodelrestoration]

@@lencac7952 Ford Performance sets the pricing on their engines, but you could still see a very small price difference. I checked over the prices and we come out a touch more expensive the Summit. I'm glad we had this little conversation. I sent the info to our product team so they can take a look at our pricing and make sure we stay competitive. Have a good day. Thanks! -Landan

[@dmfd123]

KEY POINTS: KEEP FACTORY WARRANTY! IT BREAKS, I'M COVERED. CLUTCHLESS SHIFTS. END OF STORY. I HAVEN'T EVEN BOUGHT IT BUT IT LOOKS GREAT.

[@futurec16]

Stage 1 and 2 looking like best stages

[@TOUGHBUILDSCUSTOMS]

that's the thing they just want to make money off u that's why they say to do though a ford shop lame..this world all they care for is money.

[@latemodelrestoration]

TUFBUILDS, they don't "say" go to a Ford shop to make money off of you. Having a Ford dealer complete the install is completely optional. Spending the little extra cash to retain a warranty is a good piece of mind for some owners. -Landan

[@TOUGHBUILDSCUSTOMS]

That's true if you have a warranty but I'd I can see it being a good idea to don't want to break somthing

[@sirgaddofneer]

Ive just installed a GT350CAI (not manifold) to my 16 GT. The GT350CAI only has 2 ports on it for 1x vacuum and 1x PCV. However my 16 car has 2x IMRC vacuum lines. Does anyone know what to do with my leftover 3rd line? Can I just T-joint it into the other IMRC line? Thanks!

[@latemodelrestoration]

Reference pages 11 & 12. performanceparts.ford.com/download/instructionsheets/FordInstShtM-9603-M8A.pdf -Landan

[@sirgaddofneer]

thanks landan :)

[@williamdelapena1121]

hey bud if i purchase carb legal shorty headers along with this pack can i use procal tool to tune it??

[@latemodelrestoration]

William, Unfortunately, the Procal does not adjust for headers.

[@mikehughes8023]

If you have a Coyote engine then shorty headers are just a waste of $$….Just keep the stock ones.

[@l2eggyheavy488]

They need to make power packs 2-3 for 2018+ mustangs. Or do these work ?

[@latemodelrestoration]

The Stage 3 Power Pack will only fit on 15-17 S550 Mustangs. Most 18+ owners stick with the stock intake manifold, since they perform very well.

[@aj-wq4sn]

Thinking about getting this later on...i live in a place where there are no tracks, drag strips, etc. just a feww good highway pulls. But the car scene here is no joke. Should i just go for the stage 2 or give it my all with the stage 3? Im more of a daily

[@latemodelrestoration]

Personally, I like stage 3, but I road race this car about 5-7 times a year. -Landan

[@adam100a8]

Which shops should I go to that are trustworthy that can install it for me? Do ford dealers do it?

[@latemodelrestoration]

It would be best to check with your local Ford Dealer to see if they will install this kit for you. Being a Ford Performance part, you should have no problem having them install it for you.

[@SanicGottaGoFast]

Stage 1 -410whp stage 2 - 421whp stage 3 - 432whp

[@jarronmoore8826]

if you had a Ford dealer do this for you, you could almost buy a gt350 for the difference in cost. or just get a supercharger.

[@Spiritcr1jsher]

How much crack did you smoke before this post ? A supercharger is $6500-9000 and will cost about another $1400 with installation. Then you need a new clutch , fuel pump, tires/ rims . In the end you will have a faster car but you would have spent about $10-15k by the time you were done. Much more than this pack at $2000 and $800 for an install or do it yourself .

[@sinbeecho]

Can you adjust for wheel/tire changes with the calibration tool?

[@latemodelrestoration]

Yes. -Landan

[@StevenNeidlein]

why is it only getting 395 hp when ther mustang gt come 435 stock?

[@StoreDStoreD]

those numbers are to the crank. what the actual motor pulls. the dyno measures wheel horse power(whp) which is the actual useable power. you lose 10-15% because of the weight of the car. Manufacturers never show wheel horse power. its always what it makes at the crank

[@cesararroyo86]

Install video was great and helpful. I have a manuel and redline is 7k. Am I missing something? Or is the 7.5k for autos only?

[@Trapezius_God]

I’m thinking the redline increases. In that case, maybe get the digital dash so you can see revs over 7K?

[@michaelbeers5064]

The cluster still turns red a 7k but the fuel cut off is higher, try winding it all the way out

[@14truelies]

Does the power pack 3 utilize the gt350 manifold IMRC?

[@latemodelrestoration]

Yes, the power pack does utilize the GT350 IMRC.

[@MisterJ.J.]

Is traveling 1,000 RPMs over the factory stock 6500 RPM redline safe and reliable?

[@latemodelrestoration]

This kit is still installed on the car in the video, and we have had zero problems. The car is also tracked multiple times a year. -Landan

[@jonasbaine3538]

Yes just keep the oil changed on time.

[@Sir.VicsMasher]

Would like to of seen a dyno comparison between this and the Cobra Jet intake manifold.

[@williamdelapena1121]

Can I sell it when done.? I super charged mine

[@luismelchor744]

Does this make your check engine light come on?

[@latemodelrestoration]

No, it does not.

[@axelsilvajr]

Got the code p061a, installed this, throttle body, and have an air raid intake, it's tuned by bama

[@latemodelrestoration]

We suggest contacting your tuner. Have a great a day!

[@onway5406]

Has any one done this with a Hellyon twin turbo kit?

[@drewgrows7765]

37hp gain for $1700 in parts plus labor on top.

[@mikehughes8023]

Over 70 hp gain to the wheels at over 7200 rpm.

[@RobertKohut]

Great video!!

[@williamdelapena1121]

If I use different tune like engauge will it make more hp??!? And can I retune with procal tool after?

[@latemodelrestoration]

In most cases, a custom tune will make more power, but they can void the warranty. You cannot do both though. It will have to be one or the other. Also, a custom tune is not legal in California, but the procal is.

[@williamdelapena1121]

@@latemodelrestoration thank u . U guys always very helpful. I appreciate it.

[@ozkrpalminteri9431]

all that for 30 extra hp? 😩

[@williamdelapena1121]

Can i use stock throttle body with adaptor plate?

[@chevyhs]

I think I see more torque under the curve and it peaks longer.

[@Bulltexas2011]

questions .. 1. can the Boss 302 intake be put on the 15 to 17 5.0? 2. if it can i would love to see that video and numbers

[@latemodelrestoration]

1. Yes it can. 2. We don't have a video, but there is an article out there. www.stangtv.com/tech-stories/engine/coyote-intake-manifold-shootout-gt-gt350-boss-302-and-cobra-jet/

[@stefanmyers]

How does this power pack work with say Lomg Tube Headers and Magnaflow Street or Race exhaust? Would there be more productive increase of power or counterproductive results?

[@mikehughes8023]

You need to constantly stay over 6000 rpms to feel the power gains.

[@stefanmyers]

@@mikehughes8023 sooooooo same thing with say if I go with CobraJet intake instead? Good high rpm horsepower increase?

[@floyd4311]

So if I plan upgrading the injectors and adding long tube headers with this upgrade, will I need a specific custom tune vs. the pre-cal tool?

[@latemodelrestoration]

Any modification other than what is provided with the Stage 3 kit will require a different handheld tuner and tune. -Landan

[@williamdelapena1121]

Am i able to sell product when im done with it?

[@mervyoung5397]

432WHP = 509 crank HP! I think that's a happy dyno! There's no way a GT350 intake manifold and tune will increase factory crank HP from 435HP to 509HP.

[@mikehughes8023]

Yes it does with the GT350 throttle body. The power gains are above 7000 rpms which is where this rev happy Coyote motor puts in work. This isn’t an LS or Hemi. It’s a dual overhead camshaft with higher volumetric efficiency.

[@keairkelly5875]

@@mikehughes8023 would you recommend keep you’re factory Headers on with this performance pack

[@mikehughes8023]

@@keairkelly5875 Yes, as it’s mainly the tune with the intake manifold that improves performance…

[@staggeredhorizons3657]

awesome!

[@williamdelapena1121]

If i add headers can i use pro cal tool to tune it??

[@williamdelapena1121]

so im cleaning the cold air intake.. do i need to oil after cleaning????

[@latemodelrestoration]

The factory filter in this kit is a standard non-oiled replacement. If you do want to go with a reusable option, here is the link for this replacement. lmr.com/item/M9601G/ford-performance-gt350-performance-air-filter-m-9601-g

[@gilj7147]

Why did your vacuum tube came out differently?

[@latemodelrestoration]

You may reach out to our contact us page so our tech department can try to help you out with your questions. lmr.com/contact

[@williamdelapena1121]

hey bud . quick question. can i use 100 racing fuel with this ?

[@latemodelrestoration]

I am sure this is not a problem, but you may want to consult with your tuner just to make sure.

[@Cbagz795]

The mid range is basically the same!

[@samuelaldridgesa]

How much is the Stage 3 power pack I have a 2016 GT

[@latemodelrestoration]

Samuel, here is the link: lmr.com/products/15-17-mustang-power-packs -Landan

[@331Grabber]

This information basically tells me to buy a 2018 GT

[@Spiritcr1jsher]

I don't like the 2 overdrive gears of the newer gts , slightly kills the extra power.

[@331Grabber]

@@Spiritcr1jsher I wonder if it's easy to swap an older MT82 6-Speed with the better 5th gear 1:1 ratio in there. I would definitely look to do that. I'm betting the 2018 manual picks up a tenth or two from the better gearing

[@Spiritcr1jsher]

@@331Grabber I guarantee it will since it's not that torquey of a motor and the car loves to rev . Especially with a 7400rpm redline. It's a MPG thing . I would bet 23mpg highway would be the number on an older mt82 gearbox and I also bet it's a straight forward swap.

[@331Grabber]

@@Spiritcr1jsher The weird thing is the old MT82 with 5th as 1:1 has virtually the same 6th gear overdrive ratio as the double overdrive new ones. I think Ford figured customers didn't like the huge RPM drop from 5th to 6th gear on the older MT82. My 03 Mach 1 has almost the same drop 4th to 5th but I'd never wish for another tweener overdrive gear :)

[@Spiritcr1jsher]

@@331Grabber I have the 3.73 gears on my 2015 so I dont notice it as much I guess . I'm at like 2500rpms at 80mph in 6th give or take. 2 overdrive gears sucks . My 87 gt did like 85mph in 5th at 2000rpms...lmao

[@williamdelapena1121]

Just installed mine!! Love it. Question... how do u use octane adjust? What happens if i turn it on?

[@latemodelrestoration]

You can do it on your laptop. By default, it is set to 91 octane. Give us a call at 866-507-3786 if you have any more questions.

[@reptarthetrx2408]

Has the gt350 intake manifold been tested to fit on the 2018 Mustang GT yet?

[@jlcurtis94]

Almost no point since the 18 intake is so good, people have already swapped them onto the 15-17 and made just slightly under a gt350 intake from what I've seen