2015 toyota camry front brakes and rotors

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic
#2015toyotacamry #camry #toyota #toyotacamry #camryfrontbrakeandrotors #brakes #rotors #brakesandrotors

[@leekro1]

Real world video with great explanations and plenty to learn. Nice job and thanks!

[@greg111899]

About to do this job on my mom's car along with the struts on the front end this video is very helpful thank you!

[@josemendez-cn7mg]

Very good video. Thank you.

[@tahataha-hh6gv]

Thanks bro

[@joeshand9490]

Question when I brake it sounds like one side of the brake squeezes. You can hear it go around in a circle then squeezes. I just need pads?

[@RBTheMechanic]

Re check ur work and see if ur calipers are good not possable one to work maybe ur hearing noise from one

[@akil9769]

I have the same car, and just did a brake job at a shop. The mechanic installed after market pads and rotors and now my car squeaks. What are those small pins called? I need to go to Toyota and buy originals including the shims and pins. Great Video, you’re a true professional, are you in NYC???

[@RBTheMechanic]

The hardware … but that wount resolve ur Squak it’s the pads and rotors meterial so u need to seal with another and do gracing like I show on my greasing video

[@robertrodriguez5277]

What are the torque specs on the 17m bolts and the 14m bolts awesome video super informative

[@RBTheMechanic]

I would have to check from shop pc on konday

[@kevinduzbois8909]

Show me how to remove a 2003 lesabre ignition lockswitch

[@KyalPOV]

Jeez man why so many ads. Decent channel but omg awful ads pop up too much

[@RBTheMechanic]

I will change that on up comming videos thanks buddie

[@TheChiefJudgeDredd]

Great video but the ads is killing your videos

[@RBTheMechanic]

I’ll eliminate some ads

[@mamaligakiller]

The guy needs to make money

[@entrepreneur1013]

HE NEEDS A NEW NEW CALPER BRACKET, IT WAS NEVER SERVICE

[@bigb997]

What you torque it to?

[@RBTheMechanic]

The bracket broke is 79 ft lb and the caliper slider pin is 25ft lb

[@ramonpagan1578]

Love the videos would i be able to contact you via video if possible?

[@RBTheMechanic]

No sorry

[@oshe5871]

How do you break in the new breaks?

[@RBTheMechanic]

You drive the car 35mph slow brake down to 5mph then let go brake don’t stop let the car stop drive off up to 30mph brake down to 5 do that few times don’t let the brake pads stop at one spot that’s why u come down to 5mph and continue back updo that for good 15 minutes and ur all set

[@oshe5871]

Thanks brother, it seems as though rotors get warped more often now a days. I'm not sure why. After my next brake job, I will break them in properly, maybe that will prevent warpage.

[@RBTheMechanic]

@@oshe5871 yes brake them in and avoid sidle brake slams and puddles of water

[@Jahcrooks]

My rotors are slightly rusty but NO groves, should I get new rotors?

[@RBTheMechanic]

If u don’t feel shake when braking high speed and rotor is with in thickness then u can leave it alone

[@Jahcrooks]

@@RBTheMechanic Thank you.

[@RBTheMechanic]

@@Jahcrooks welcome

[@kevinduzbois8909]

Show me how to remove a 2003 lesabre ignition lockswitch

[@RBTheMechanic]

Don’t have tho come to me if I do I will do the video I did them so many time years back

[@kevinduzbois8909]

I'm sure I'll be needing you again,thanks.

[@RBTheMechanic]

@@kevinduzbois8909 no problem I’m always here to help !!! Msg me anytime …!!!