2JZGTE VVTI wiring made easy!

[@WHOISTRANE]

ABOUT IMMOBILIZER!!! You CAN turn it off with original immo circuit (amplifier, coil and key from the same car from which you've bought that ecu). Also you can install key emulator in ecu. AND ALSO you can reprogram eeprom in ecu with immo-off-dump to kill immo system!

[@Danthewelder]

How?

[@WHOISTRANE]

@@Danthewelder sorry for the long reply. 1. original immo circuit. you need original immo stuff. wires, amplifier, coil and key. you can use any toyota/lexus key with TIRIS 4C chip inside, but you need to reprogram a 93C56 eeprom (IC900) inside ecu, you need to program "virgin dump" in it. after that ecu should learn new key and you'll be able to start the engine. www.instructables.com/DIY-Immobilizer-Hacking-for-Lost-Keys-or-Swapped-E/ 2. you need to buy or make yourself a key-emulator. you can make it with arduino and some NPN-transistors. 3. don't know about if there is an "immo off dump" for that ecu. but if so you can reprogram 93C56 eeprom (IC900) with it and engine should start. I saw that dump for 2JZ-GE (natural aspirated version of that engine), but it can be useless for 2JZ-GTE...

[@WHOISTRANE]

@@Danthewelder kzbin.info/www/bejne/f4bGqH18ea-NpdU

[@Firion13]

Dude I have been trying to find this info for years. Thank you for posting this! You're awesome.

[@edbo10]

lol this popped up in my recommended while I was looking for how the stock 2jz-gte intercooler piping is set up, had no idea you messed with an aristo, nice!

[@DakotaWoodHD]

Haha yeah man! I put it inside my 73 Datsun 240Z

[@edbo10]

@@DakotaWoodHD damn that thing must've shot off like a rocket, power to weight ratio must be stupid high lol

[@peterjoseph2803]

Can't wait to get started . THANKS for YOUR upload!☆☆☆☆☆

[@jacobjones1009]

Using the aristo engine, trans, and ecu. In a 2005 is300 auto. Getting fuel delivery, spark, and crank but no combustion. The injectors aren’t pulsing I think and the maf connection isn’t hooked up.

[@xXNoobOfDoomXx]

Awesome video, will be using this to wire up my cressida wagon swap. Nearly to the point of pulling the 5MGE. Just need to remove the exhaust and driveshaft.

[@dennisbdavid]

gamefreak054 I’m doing the swap soon myself. How is yours doing? Did this vid work with your swap?

[@jouflux]

Thank you for the info, my 91 toyota pickup live again with a 2jzge vvti. I was missing 3 wire from the ecu

[@lanceson2461]

this video has been very helpful. but if the ecu has a grey plug all u need is a virgin flash. visit a local immo shop

[@kamroon]

Yo! Is it possible to see info on wiring your engine harness to your standalone? Im specifically interested in all the throttle body wires

[@dannylanderos3729]

Does this also work for a gs300 2jz-ge engine??

[@tcollogan]

Fyi there is a Russian that is able to bypass the immobilizer he has a Facebook group Toyota ecu security off his name is Yuri

[@bhp4298]

Hi can u just tell me how to connect the steering wheel shift buttons wiring ground which is the manual mode … it wd b appreciative

[@riceball4u172]

Thanks, the color code really simplify things. Like and sub

[@ak-il3ze]

Hey what’s going on man! Nice video!! Really helpful I’m doing the same swap to my 98 SC300 vvti. Any idea where I can get the pinouts for my sc harness so I can modify my aristo vvti harness accordingly? Thanks

[@NTC4]

Great Job! Just one mistake man, in F60, pin M-Relay is power outlet and not power inlet. If you do that the Accessories will stay on after turning of the ignition.

[@TripasGarage]

I just noticed that also when making my notes right now! In almost all of the videos online, everyone seems to use this as an Input. So technically, what do we do with this M-REL wire?

[@felipefalcon4811]

The ecu sends power to switch the efi main relay n1

[@GaryLaaks1]

Ok so I have set a goal to try this this week. My 2JZ has been in my garage for a year now. You make it look so easy. Tks for this video. Motor is still on the ground on some old tires. Plan is to build it into my Nissan 200SX. Still looking for a decent manual gearbox, flywheel, clutch and driveshaft. EVERYTHING costs a fortune in South Africa mate. Motor from an Aristo and it cost me R40K. Thats like 2500 USD. Is that expensive in the states? Kind regards

[@BicepRahman]

In england its about £2,500 for a bare 2jz-gte

[@manolaq]

MREL is not needed unless you simulate the original circuit. How it works? When you turn on the key power goes to IGSW. Then MREL is sending power to main relay and when this relay is activated is sending power to +B and +B2

[@allboost70]

Immobilized ECU's can be used on vehicles equipped with immobilized systems like a Lexus IS, GS, etc, but only with the immobilized ECU's original master key. With both you can have a Toyota dealership flash and reprogram to suit the new immobilized chassis.

[@DakotaWoodHD]

M Fournier M Fournier Sorry my video was unclear. In the beginning I was driving in my friend's car who is already running a standalone ECU. I am going to make a revised video with all the new info I gathered from reading the forums. Along with what you stated, I forgot to add the M- relay to properly run the engine in the cae. I will change the title maybe to " How to initially start your 2JZGTE VVTI" and then I will make a "How to properly wire your 2JZGTE VVTI engine swap".

[@allboost70]

wasn't aware it was a different car but yeah figured I'd mention it while video was still fresh. And could also mention the guys who can convert these ecus who you found on FB lol

[@DakotaWoodHD]

I appreciate it! & yeah lol I thought it would make for a cool intro clip 😂

[@jaynove]

DakotaXPRO this vid has shed a light on the wiring. Could you do a vid on the full pinout from the old ECU to 3 grey plug ECU?

[@DakotaWoodHD]

Julius yes I will work on that soon

[@allanfolkes6019]

The bigger injectors is it to the stock brain and if so could you make a video on the resistor pack and how it works

[@FayazKhan-zr5nf]

I need 2jz D4 wiring diagram can you help me

[@djpacheco8506]

hi how are you. i have a question. is this the same for an 04 is300 2jzge vvti? please help me thanks.

[@turbogears900]

And you help me with the 1jzgte none vvti. I need to wire it the work in a 93 lexus sc300

[@kevinfundora2979]

I wire a 2jzgte vvti and i don’t have spark on the first coil and the last one the middle one got spark and one side of the plugs have power all 3 any help it will be great i use this video for my wiring

[@DakotaWoodHD]

kevin fundora I would switch one of the coils that work with one that is bad and see if that one works. If it does then you just need to replace those two coils. Hopefully that will work

[@kevinfundora2979]

DakotaXPRO got working thanks !!

[@Izzy-ww1vh]

This will be the same for a 98 GE VVTI ? from a IS300 ? I’m learning about the 2jz very new to it. Just got one so I’m a noob. Please respond so I can make sure this works for me.

[@المهندس-ابوهشام]

What about fan , steering pump, engine ground,

[@المهندس-ابوهشام]

The last but not the least, do we need transmission connectors?

[@tinle8757]

الدحمي بن هشام i

[@turbogears900]

Good evening I need some help with getting my 1jzgte none vvti started from the ignition key on my 93 ac300

[@gold_digger_7399]

Thanks for the video and information

[@freestyleskyline]

What are you doing about the drive by wire throttle body? Did you delete it?

[@Alientraveler003]

Yea no no I’m looking for the ge jz80 2 prongs on the ecu it’s older and one has the size 10 mill bolt 80 pin and the other is a 40 pin plug looking for wide band o2 sensor( 3rd)lower one sensor , any help pls anyone

[@boonfootai8605]

Don't you have a tooth box? I'm looking for a dental box profile. Electrocardiogram of automatic dental box.

[@salahalzeyadi5142]

Nice work 👏 👌 👍

[@williamcruz364]

Ok I have a 2002 LS300 I WOULD LIKE THE PINOUT

[@allanfolkes6019]

Hi good day im wiring one and looking for the speed signal. Tach. Oil pressure neutral drive manual 2nd L could you help me with that most important speed im from trinidad and we have some strict speed timing so i would like to know so when im in that kind of zone i could take it down a bit at least till i pass lol

[@aaronmaduro7528]

What do you by run+crank ??? Please let me know

[@maciejgrzeskowiak6241]

Switched 12v, there is voltage when ignition is on and when u crank engine at least from what i know

[@owenalejandroalvarezmancil4639]

Alguien sabe como qitar el inmovilizador de la ecu del motor 1jz gte con vvti

[@jasonfontaine3741]

These are going to be very similar to the jzs171 1jzgte vvti wiring? I am under that impression. Just wondering if you can confirm

[@Mr.S2]

you are right , i have just done the conversion

[@B2JZ]

Hi man I need help with my 2j

[@erickhernandez1171]

How i make secuential mode with it

[@RakTheGoose]

why is the idle so high

[@AaronMacruairi]

What about using an auto ecu but with a manual swap? Any wiring to make the ecu think its in park?

[@mardicas]

A it late reply, but you need to make the ECU think it is in "L" gear as VVTi will work in it and it won't try to shift the Auto box(no hesitations).

[@mardicas]

And if you think you need "P" to start the car then you don't, only need to connect the "safety" pins of the ATM plug (black+black/white).

[@illshlapu]

God bless ya man

[@joseluisperez8909]

It's the same for 2jz non vvti???

[@boosteds1440]

What ecu do I use then?

[@badrussian4999]

Great car! I like!

[@Boostlifelex]

Is there anyway you could help me wire up the Eshift on my 2jz gte vvti swapped gs400? I've been searching around for 3 months and nobody knows

[@ArmyofSeaturtles]

its on clublexus,

[@Boostlifelex]

@@ArmyofSeaturtles where I've searched and searched and never found a how to wire Eshift? There's one post that attempts to describe it but it's incorrect

[@dydrianfyzo6159]

Im from trinidad if i had paypal i would of donate but i sub. Nice work g

[@jackmcwatters7383]

I only made it to step one. FFS. props for info though.

[@jdmunit8017]

Does the dash speedo still work?

[@spychat2000]

No it wont as the system / ecu will not communicate with dash in this setup You need full harness to be able to achieve this plus conversion ecu for example haltec or elite standalone ecm which i personally believe is much better than stock

[@WHOISTRANE]

can you give a music name please?)

[@raulrodriguez350z]

Tanks you man

[@mr.valentino2824]

Will this schematic work for the 2jzge vvti engine?