3D PRINTED RC BOAT WATER JET

[@pilotoleng6357]

Wahh... Bagus banget👍

[@Mr.RC-Creator]

Thanks.😁

[@55steviegreene]

That's awesome. What 3D printer did you use?

[@Mr.RC-Creator]

I use 3D printer BIQU B1.🙂

[@donaldfite]

I'm going to try it. Any links for where you bought the hardware? Drive shafts, rivnuts.... Thanks

[@Mr.RC-Creator]

th.aliexpress.com/item/33047616164.html?spm=a2g0o.detail.1000014.39.696883TP83TPDn&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.362094.0&scm_id=1007.40050.362094.0&scm-url=1007.40050.362094.0&pvid=61b83da7-3c39-4853-aa3d-c55a90998229&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.362094.0,pvid:61b83da7-3c39-4853-aa3d-c55a90998229,tpp_buckets:668%232846%238115%232000&pdp_npi=4%40dis%21THB%2155.96%2141.97%21%21%211.60%21%21%402101c5b117029660616465015eff17%2167421173719%21rec%21TH%21173671390%21 th.aliexpress.com/item/32934303589.html?spm=a2g0o.productlist.0.0.372352b5npeY9O&algo_pvid=46c1fc5d-8e54-4de1-a4bf-158b1c434ef0&algo_exp_id=46c1fc5d-8e54-4de1-a4bf-158b1c434ef0-0&pdp_ext_f=%7B%22sku_id%22%3A%2266132994816%22%7D&pdp_npi=2%40dis%21USD%21%213.96%21%21%21%21%21%402103399116539077670891060e7c93%2166132994816%21sea

[@lorenzobacci9442]

hello, great project, I have just finished this project but I have a question, Is possible to run the boat with a 60C 3s battery, higher C is better or worst ?

[@Mr.RC-Creator]

It's really nice🙂 I'm sorry for the late reply.

[@the-matrix-has-you]

Hi, very well designed project, How many 1 Kg of PLA+ spools are required for all 3D printed parts? you have written on video description as 3-4 but I need the exact kg of PLA+ needed before ordering filament Thank you.

[@Mr.RC-Creator]

Thanks a lot! Approximately 2 rolls of PLA+ filament

[@JordanWalsh-uz7gh]

Other than the water cooling holes and the air lock hole have you altered this in any way from bashtecs design I'm asking coz I've started printing bashtecs design and bought bearings etc and would like to print the rear part of the hull from your design ?

[@Mr.RC-Creator]

No, I don't change this from bashtecs design.

[@SilverbackSasquatch19xx]

I am currently printing this I plan on using my spare traxxas 1/16 power system vxl 3m and 380 brushless motor, the motor measures 2848 and is 4000 kv

[@Mr.RC-Creator]

You can use Traxxas 1/16 parts, I think it works.😁

[@dragonconley44]

Great video but you left out installing the prop shaft and everything else that goes along with it. One of the most important things to make the jet boat go and work properly. I figured it out but the way the prop is printed out looks backwards. Sorry for the negative comment but I'm sure others would also feel that you left the most important part out.

[@Mr.RC-Creator]

Hi.Dragonconley Yeah, I think it's gone too.😅

[@dragonconley44]

@@Mr.RC-Creator also left out the water cooling which is different from the boat that I printed out. I tested my boat last night I’m my pool and it’s going to be a ripper other than it overheated a couple times because I don’t have any water cooling setup yet. It’s still needs to be sanded and made waterproof but it’s the small things that I still need to do.

[@keybrent64]

@@dragonconley44 What are the dimensions on the prop shaft size? I think I've seen a link for every part but that lol. That's the missing piece I need to finish my boat

[@dragonconley44]

@@keybrent64 I will find it and send you the link.

[@albertorodrigo3602]

I need link too!

[@quentinorhant5219]

Hey, do you remember the print settings, I'm tempted to print at 100% infill, but maybe 3 layers of perimeters and 20% infill is enough?

[@Mr.RC-Creator]

I don't remember, infill it's not 100%

[@chimonoki2868]

Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 10-15 Filament brand: esun Filament color: Orange Filament material: PLA

[@Mr.RC-Creator]

I agree with you!!

[@bkumler]

Thanks for your last reply. Do you ever have problems with airlock?

[@Mr.RC-Creator]

Not at all,🙂

[@Mr.RC-Creator]

@bkumler You have a problem with that?

[@bkumler]

Yes, when I was running it last week on the ocean, I did. I thought that brass fitting and tube was away to prevent that, allowing the air escape.

[@Mr.RC-Creator]

​@@bkumler Ah, I see. I thought.🙂

[@daberberger6743]

hey thank you for the video its great! how did you installed the Bearings and SHaft and what did you use to make it waterproof? I am new to boat stuff so i am not sure. My inital Idea was to use 2 x 2-RS Bearings with the shaft, but i am not sure if this is already enough?

[@Mr.RC-Creator]

I put some white grease on the shaft after the bottom of the hull.

[@TheAntricos]

Where the top hole (for the tube) is conected? I understand that the one in the back is providing water for the watercooling with an outlet on the side but what does the one on the top do?

[@Mr.RC-Creator]

The top hole is for grease and lubricant for the drive shaft and bearings. (For pipes) worn to prevent water pressure from flowing in.

[@TheAntricos]

@@Mr.RC-Creator I got that one, I am asking about the other one the big hole behind the small for the grease.

[@Mr.RC-Creator]

@@TheAntricos It is the water inlet pipe for cooling.

[@TheAntricos]

@@Mr.RC-Creator So it has 2 water inlets? One there and one in the back near the propeller? Also thank you for taking the time to reply!

[@Mr.RC-Creator]

Yeah.!!😁

[@mahmoudsaad271]

Great build , i got u used the water inlet from the end of jet tunnel to cool the esc,motor inline,, what what is the purpose of the water inlet on top of the tunnel as it is not clear where the pipe route go

[@Mr.RC-Creator]

Hi.Mahmoud Water inlet at the top of the tunnel I use grease to lubricate the shaft and prevent water from entering the bearings.😁

[@mahmoudsaad271]

Thanks for ur reply , so u added two bearing to the drive shaft ? And what size of these bearing ?

[@Mr.RC-Creator]

@@mahmoudsaad271 Bearing size 9x4x9🙂

[@crashsquared]

Hey!! Lovely model! Just printed it and built everything. One thing confuses me... I connected my water cooled esc and motor to the rear inlet on the jet and drilled a hole above-water on the side of the boat for the outlet. Thing is... water's going the other way round the system! When the outlet is below water it draws water from there and exits from the jet. What am I missing?!

[@Mr.RC-Creator]

Thanks.! 😁Try running the cooling system lines to see if they are reversed? Normally they must go in the same direction.

[@crashsquared]

@@Mr.RC-Creator Hey thanks. Not sure I understand what you mean. I can simplify the problem... if I just connect a tube to the rear inlet on the water jet... no water comes out. And if I put the other end of the tube in the water, water will flow from the end of the tube to the water jet. As if the jet has negative pressure which doesn't make sense. Other than that the boat seems to work great (I did check reversing the motor direction). I'll try and get a video to share...

[@crashsquared]

@@Mr.RC-Creator I was about to make a video when I think I figured it out! The prop is way back, after the inlet. So the inlet is on the low pressure side and hence it pulls instead of pushing! I'll either need a new shaft or will move the intake outside the boat body to draw water from after the prop. Mystery solved!

[@Mr.RC-Creator]

@@crashsquared Wow, great! Great! You are so good at solving that problem yourself.🥰

[@Mr.RC-Creator]

@@crashsquaredThat's awesome!

[@boyankinky3032]

Ohhh Boy!! Pretty slick on the design . Whats the total cost on this ? Inclusive for parts and motor?

[@Mr.RC-Creator]

Hi. You can buy it by following the link. www.aliexpress.com/item/1005002395921310.html?spm=a2g0o.productlist.0.0.677671f1bc66fm&algo_pvid=f0fc7e6a-a021-455f-b68a-9be004b89843&algo_exp_id=f0fc7e6a-a021-455f-b68a-9be004b89843-8&pdp_ext_f=%7B%22sku_id%22%3A%2212000020510007646%22%7D&pdp_pi=-1%3B36.92%3B-1%3B291%40salePrice%3BUSD%3Bsearch-mainSearch www.aliexpress.com/item/32760616516.html?spm=a2g0o.productlist.0.0.35024615MnIpWz&algo_pvid=d9ebf978-14b2-4b32-a656-958583d42ae6&algo_exp_id=d9ebf978-14b2-4b32-a656-958583d42ae6-2&pdp_ext_f=%7B%22sku_id%22%3A%2262050185408%22%7D&pdp_pi=-1%3B32.99%3B-1%3B-1%40salePrice%3BUSD%3Bsearch-mainSearch www.aliexpress.com/item/1005001943578133.html?spm=a2g0o.productlist.0.0.41625a98pxK6EL&algo_pvid=fa54fb48-8660-40ee-84f1-9a3d678e8e75&algo_exp_id=fa54fb48-8660-40ee-84f1-9a3d678e8e75-7&pdp_ext_f=%7B%22sku_id%22%3A%2212000018177977674%22%7D&pdp_pi=-1%3B9.17%3B-1%3B-1%40salePrice%3BUSD%3Bsearch-mainSearch

[@fernandov9078]

PLA is very permeable. How do you solve this?...thank and great video

[@Mr.RC-Creator]

Hi.Fernando V Thank you so much.😁 I coat it with clear spray.

[@bkumler6394]

Hello, whats the brass fitting and clear hose for right behind the motor and that small screw?

[@Mr.RC-Creator]

@B Kumler Brass fittings and clear pipes reserved drain pipe. Small screw, close the water pipe.

[@AdamKrushel]

hope you see this but can you tell me where you got the shaft and coupler?

[@Mr.RC-Creator]

th.aliexpress.com/item/2251832754435647.html?spm=a2g0o.productlist.main.5.32d3TzuZTzuZbz&algo_pvid=05318163-eb7c-490c-ba1e-649ce8db6f4a&algo_exp_id=05318163-eb7c-490c-ba1e-649ce8db6f4a-2&pdp_npi=4%40dis%21USD%215.95%214.46%21%21%215.95%214.46%21%402103085c17186046760617711eab6e%2166582458376%21sea%21US%21173671390%21&curPageLogUid=BtATQ8aDPjeh&utparam-url=scene%3Asearch%7Cquery_from%3A th.aliexpress.com/item/3256801305009792.html?spm=a2g0o.productlist.main.37.32d3TzuZTzuZbz&algo_pvid=05318163-eb7c-490c-ba1e-649ce8db6f4a&algo_exp_id=05318163-eb7c-490c-ba1e-649ce8db6f4a-18&pdp_npi=4%40dis%21USD%215.89%215.60%21%21%215.89%215.60%21%402103085c17186046760617711eab6e%2112000016330455606%21sea%21US%21173671390%21&curPageLogUid=i3qohRmaMTLr&utparam-url=scene%3Asearch%7Cquery_from%3A th.aliexpress.com/item/3256806675485980.html?spm=a2g0o.detail.pcDetailBottomMoreOtherSeller.22.6435GSdXGSdXu3&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.354490.0&scm_id=1007.40050.354490.0&scm-url=1007.40050.354490.0&pvid=5f55d28c-27fb-438b-9b83-f2ed72a6308c&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.354490.0,pvid:5f55d28c-27fb-438b-9b83-f2ed72a6308c,tpp_buckets:668%232846%238109%231935&pdp_npi=4%40dis%21USD%211.49%211.49%21%21%2110.77%2110.77%21%402101584517186047980984594e58e8%2112000038547818462%21rec%21US%21173671390%21&utparam-url=scene%3ApcDetailBottomMoreOtherSeller%7Cquery_from%3A

[@Amish_Mafia]

Hey I hope you'll still reply to comments, where did you find those nutserts your heating and placing in the screw holes? I like that idea I assume that would be stronger than just threading the screws straight into plastic.

[@Mr.RC-Creator]

Hey I used a PCB to support the mounting bracket to prevent the plastic from softening when it gets hot.🙂

[@geg5274]

did anyone have problems with the pieces not fitting properly when trying to assemble the hull?

[@Tdubplayz]

I’m having trouble did you ever get it on?

[@Mr.RC-Creator]

Where are you having problems? Please tell me your problems.

[@Tdubplayz]

@@Mr.RC-Creator whenever you put the backpiece in the piece that connects to the backpiece it has a lot of problems and I had to spend about 30 minutes shaving it down with a knife to the perfect size

[@Mr.RC-Creator]

@@Tdubplayz Perdón por mi tardía respuesta. Eres muy talentoso y maravilloso al poder resolver esos problemas.🙂

[@Tdubplayz]

Thank you😊❤

[@AJ-xm6yg]

Nice boat design. Poor build instructions pertaining to the drive shaft and cooling. I see parts list provided by creator and others which vary. As an example 10x4 bearing. Someone else says 9x4 bearing. After printing I measure bearing seat and get 8mm. The drive shaft tube for the 4mm shaft is 9mm in diameter. How does that fit a 8mm hole. My printer is the bambu X1C so it's very accurate. I understand the inlet water cooling off the prop housing and then the outlet further back on the prop housing. So why in the video was there an hole drilled in back along with 2 on the side haul? Confusing.

[@Mr.RC-Creator]

Thanks!! You can do this if you have the required parts. And printers have many different error values. and you can drain the water as needed. The other 2 holes in the back I made as a reserve.🙂

[@sergiosanchez_09]

And the length of the metal transmission tube?

[@Mr.RC-Creator]

D4mm, L150-200 mm🙂

[@ChampTruex]

where did you get the bent servo push arm lol,

[@Mr.RC-Creator]

You mean servo arm, right?🙂

[@ChampTruex]

@@Mr.RC-Creator yeah

[@Mr.RC-Creator]

@@ChampTruex It comes with servos.

[@ohladthekewlkid1467]

im wondering if that is the top speed? could you go faster in a larger pond, if not then what kv rating would you recommend for a faster boat?

[@Mr.RC-Creator]

This can be faster, I use 50% throttle for the clip 😀

[@ohladthekewlkid1467]

@@Mr.RC-Creator thank you

[@ohladthekewlkid1467]

@@Mr.RC-Creator ima build this

[@Mr.RC-Creator]

@@ohladthekewlkid1467 Have a good time.😁

[@esosfpv]

What type of screws and nuts did you use?

[@Mr.RC-Creator]

Sorry for my late reply I use M3 Stainless Steel Hexagon Hex Socket Screw 😁 www.aliexpress.us/item/3256806157900927.html?spm=a2g0o.productlist.main.23.1bd31dadlIAjte&algo_pvid=0feb8407-78f6-4801-a2c7-286fe6488624&algo_exp_id=0feb8407-78f6-4801-a2c7-286fe6488624-11&pdp_npi=4%40dis%21USD%213.19%211.69%21%21%2122.70%21%21%402103225217047148847791170ed79e%2112000036843204582%21sea%21US%21173671390%21&curPageLogUid=j5gTTuPRW9Ew

[@KK3DTechnology]

Which dimension shaft are used for propeller ..?

[@Mr.RC-Creator]

Drive shaft 4mm

[@KK3DTechnology]

@@Mr.RC-Creator and length

[@Mr.RC-Creator]

length 150cm

[@KK3DTechnology]

@@Mr.RC-Creator thank you sir

[@module-prestashop]

Hi! Ken you tel me please from where did you get the connectors for cooling tubs and what glue use ?. Thank you!

[@Mr.RC-Creator]

Sorry for the late reply. th.aliexpress.com/item/1005003958009739.html?spm=a2g0o.detail.1000014.23.5622DKxtDKxtIf&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.362094.0&scm_id=1007.40050.362094.0&scm-url=1007.40050.362094.0&pvid=58cf09be-eb1a-48f2-9937-ef64f07f37df&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.362094.0,pvid:58cf09be-eb1a-48f2-9937-ef64f07f37df,tpp_buckets:668%232846%238110%231995&pdp_npi=4%40dis%21THB%2198.11%2151.86%21%21%212.80%21%21%402101c5a717017767177161700e0ca3%2112000027568323828%21rec%21TH%21173671390%21 th.aliexpress.com/item/1005005073643814.html?spm=a2g0o.detail.0.0.67dcu5CBu5CB2W&gps-id=pcDetailTopMoreOtherSeller&scm=1007.40050.362094.0&scm_id=1007.40050.362094.0&scm-url=1007.40050.362094.0&pvid=8059653c-84c9-4510-a410-307ac2395747&_t=gps-id:pcDetailTopMoreOtherSeller,scm-url:1007.40050.362094.0,pvid:8059653c-84c9-4510-a410-307ac2395747,tpp_buckets:668%232846%238110%231995&pdp_npi=4%40dis%21THB%21106.91%2164.15%21%21%2121.70%21%21%402101c5a717017767055421556e0ca3%2112000031532716499%21rec%21TH%21173671390%21

[@matthwy1]

How did you secure the propellor to the shaft? And did the shaft go through the prop and terminate in the back bearing in the stator?

[@Mr.RC-Creator]

Hi.matthwy1 You can use Drive Dog the same size as the shaft. Yes, there is a locking bearing behind the axle.🙂

[@joemamaobama.]

what are the dimensions of the bearings you used

[@Mr.RC-Creator]

If I remember correctly 9*4*9 🙂

[@diemodellbaucrew]

Nice boat, i print this boat also. At the moment, i am searching to the shaft? I don not find the right size. Have you an tip for me?

[@Mr.RC-Creator]

Hi.Sebasian Thank you!! i use a 4 mm shaft, 4 mm shaft coupling and the motor shaft size is the same 4 mm.

[@dragonconley44]

I used a 150mm by 4mm shaft and I ended up having to cut it down about 5mm but you probably figured it out by now but if not you can buy them on Amazon.

[@Mr.RC-Creator]

@@dragonconley44 Thanks.🙂

[@YohannCIURLIK]

Hi. Do you have the full hardware part list ? Especially bearings and others parts that we are not seeing on the video please ? Also, do you tried it with a 3S battery ?

[@Mr.RC-Creator]

Hi.Bro! Yes. I uesing 3s www.thingiverse.com/thing:5424311/files

[@sergiosanchez_09]

Can the boat propeller be bought?

[@Mr.RC-Creator]

You can download it from this link. www.thingiverse.com/thing:542...

[@MikelaMenace]

hello, I'm a little lost for the motor axis. I don't know anything about RC boat. Do you have the reference or a URL to buy the correct motor shaft? Thank you

[@Mr.RC-Creator]

Hi.Mike follow this link th.aliexpress.com/item/32934303589.html?spm=a2g0o.productlist.0.0.372352b5npeY9O&algo_pvid=46c1fc5d-8e54-4de1-a4bf-158b1c434ef0&algo_exp_id=46c1fc5d-8e54-4de1-a4bf-158b1c434ef0-0&pdp_ext_f=%7B%22sku_id%22%3A%2266132994816%22%7D&pdp_npi=2%40dis%21USD%21%213.96%21%21%21%21%21%402103399116539077670891060e7c93%2166132994816%21sea

[@MikelaMenace]

@@Mr.RC-Creator thx :) !

[@MikelaMenace]

@@Mr.RC-Creator this version it's ok ? Length L15cm H10cm ?

[@Mr.RC-Creator]

@@MikelaMenace Is it the hull? I thought it was small but it could be done.

[@sergiosanchez_09]

Does it work with 14.8v?

[@Mr.RC-Creator]

sure can use.

[@ohladthekewlkid1467]

what size bearing and what size shaft

[@Mr.RC-Creator]

Bearing 4x4x9 shaft drive 4mm.😊

[@sergiosanchez_09]

What size is the motor transmission?

[@Mr.RC-Creator]

2968 / 3200-3400KV

[@kacykpl]

Hi, Do You have any link to shaft ? Any dimensions of it ? :)

[@Mr.RC-Creator]

www.amazon.com/Fielect-Shaft-Assembly-Propeller-Universal/dp/B083NY6MBQ/ref=sr_1_1_sspa?crid=A4R0YXX5BK7E&keywords=drive%2Bshaft%2B5mm&qid=1660652565&sprefix=drive%2Bshalf%2B5mm%2Caps%2C305&sr=8-1-spons&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzQ1pCM1hSNzhXVzZFJmVuY3J5cHRlZElkPUEwMTgyOTI4MUtZQkMwU1NBVFFCRiZlbmNyeXB0ZWRBZElkPUEwNDM2NDcxM1BSRUdZVkE4MEdDQiZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU&th=1 D 5mm, L150-200 mm🙂

[@leelaurence-zi1tw]

Would you mind to tell me that the D 5mm, is D for diameter? Thx

[@Mr.RC-Creator]

@leelaurence-zi1tw 4mm Drive shaft. I just found this on AliExpress: THB149.57 | 2 PCS High-Precision 4mm Stainless Steel Ship Propeller Support Shaft And Bushing Set Various Sizes For Remote Control Boat a.aliexpress.com/_olhHLGN

[@sergiosanchez_09]

Could you put the link of the motor transmission?

[@Mr.RC-Creator]

THB 110.55 20%OFF | 10/13/15/20/25/30/35cm Length Stainless Steel Tube Spare Parts 4mm Stainless Steel Shaft Suitable For RC Electric Racing Boat a.aliexpress.com/_mLeRawm THB 1,025.34 51%OFF | Rocket-RC 2948 2958 2968 3400KV 3450KV 3800KV 4800KV Motor with Water Cooling Jacket for 600-800mm RC Boat a.aliexpress.com/_mqNtq6q

[@laurentoutan9922]

Bicarbonate de soude + colle cyanoacrylate= plastique super dur et ponçage,

[@Mr.RC-Creator]

👌😁

[@Rckid28]

How does the drive system work? And what parts are needed?

[@Mr.RC-Creator]

Hi. FreefallFVP follow link www.boat-ed.com/wisconsinrental/studyGuide/Jet-Drives/103051_55511/ the main components motor, drive shaft, propeller and streeing nozzle.

[@ducprinting4414]

How is your cooling water route?

[@Mr.RC-Creator]

Hi. you watch the video minutes 3:00 -3:25

[@MrJavitominicooper]

Hi. Fantastic channel!!. Im trying to build mine. Could you tell me witch Shaft did you usé? Thanks thanks thanks!! Love your builds!!

[@Mr.RC-Creator]

Hi. So you asked me, you mean the shaft of the boat, right? I use Drive shaft stanless 3mm, length 17cm.

[@MrJavitominicooper]

@@Mr.RC-Creator thank you so much! I only find 15 or 17 cm Shaft. 😞

[@Mr.RC-Creator]

@@MrJavitominicooper I believe you can do it.🙂

[@jakobporterz3211]

Are you willing to share the file for the printer?

[@Mr.RC-Creator]

Hi. Jakob Link 😁www.thingiverse.com/thing:5424311/files

[@sergiosanchez_09]

What voltage is the battery?

[@Mr.RC-Creator]

11.1volt

[@sergiosanchez_09]

Thanks

[@jonathanjo4273]

Petg.abs or pla?

[@Mr.RC-Creator]

PLA+.

[@sergiosanchez_09]

Could you put a sketch of the water cooling, I don't quite understand how it works?

[@Mr.RC-Creator]

Water will enter through the drive pipe. and send it to speed controller and finally the motor.

[@ganeshpingle.8423]

Hello Sir I am a student From india i am see your this video (Wiper Moter as a servo.)and i have some small Queshion in that can you please please help me to give the answers...??

[@Mr.RC-Creator]

Sure, I will definitely recommend it to you.

[@ganeshpingle.8423]

thank you sir can you please give me your contact so that I contact you to give my answers..@@Mr.RC-Creator

[@jamessinclair2281]

What is a Battery LiPo SS?

[@Mr.RC-Creator]

3S 2200mah.

[@pandusdog6307]

can you please give me links for the parts like motor and the melt in things and bolts

[@Mr.RC-Creator]

Hi. Pandus dog www.aliexpress.com/item/32968483467.html?spm=a2g0o.detail.1000014.5.1c97100631A8we&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.274735.0&scm_id=1007.40050.274735.0&scm-url=1007.40050.274735.0&pvid=5edc1d2f-fac5-4597-9995-81552b6bea17&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.274735.0,pvid:5edc1d2f-fac5-4597-9995-81552b6bea17,tpp_buckets:668%232846%238115%232000&pdp_ext_f=%257B%2522sku_id%2522%253A%252266641140822%2522%252C%2522sceneId%2522%253A%252230050%2522%257D&pdp_pi=-1%253B0.8%253B-1%253B-1%2540salePrice%253BUSD%253Brecommend-recommend th.aliexpress.com/item/32760616516.html?gatewayAdapt=glo2tha&spm=a2g0o.productlist.0.0.35024615MnIpWz&algo_pvid=d9ebf978-14b2-4b32-a656-958583d42ae6&algo_exp_id=d9ebf978-14b2-4b32-a656-958583d42ae6-2&pdp_ext_f=%7B%22sku_id%22%3A%2262050185408%22%7D&pdp_pi=-1%3B32.99%3B-1%3B-1%40salePrice%3BUSD%3Bsearch-mainSearch th.aliexpress.com/item/32765780418.html?spm=a2g0o.productlist.0.0.c5a051e0SmDGck&algo_pvid=b8fcd65c-9ec6-4dab-b4bd-7bbe94c7e263&algo_exp_id=b8fcd65c-9ec6-4dab-b4bd-7bbe94c7e263-10&pdp_ext_f=%7B%22sku_id%22%3A%2262203030842%22%7D&pdp_pi=-1%3B1.04%3B-1%3B-1%40salePrice%3BUSD%3Bsearch-mainSearch th.aliexpress.com/item/32614416689.html?spm=a2g0o.productlist.0.0.14f15347WpyFNf&algo_pvid=7614b66d-b76b-4626-b1f8-6e8ec12113dc&algo_exp_id=7614b66d-b76b-4626-b1f8-6e8ec12113dc-17&pdp_ext_f=%7B%22sku_id%22%3A%2265516808801%22%7D&pdp_pi=-1%3B1.33%3B-1%3B-1%40salePrice%3BUSD%3Bsearch-mainSearch

[@pandusdog6307]

@@Mr.RC-Creator thank you

[@problematic7993]

What distance does it travel before the battery runs out?

[@Mr.RC-Creator]

5-8 minutes to play

[@ingetys]

Hello Great work! I would just like to know where the pipe goes from the water inlet at the top of the tunnel? I really can't see in the video Thanks a lot

[@Mr.RC-Creator]

Hi.Thanks water pipe out to the back.

[@ingetys]

@@Mr.RC-Creator Hi, Thanks for your quick answer :-) And what is this water circuit for?

[@Mr.RC-Creator]

@@ingetys I made it to prevent water pressure. You can turn it off.🙂

[@ingetys]

@@Mr.RC-Creator ok got it Thanks !

[@justwhatever]

This is incredible build and yet a simple/effective design. Can you share the 3D models?

[@Mr.RC-Creator]

you can do this from the link above.

[@justinjanes3361]

@@Mr.RC-Creator the edits you did with the files are not available is there any way you can share your remix on thingiverse so others can enjoy the water cooling aspect. also for the water cooling is the pump nessessary?

[@Mr.RC-Creator]

@@justinjanes3361 I have not altered the original file, I am ready to help you.🙂

[@justinjanes3361]

Ok because I just finished printing the file that was up on thingiverse and there is no deed spots like what was done for the water cooling in and out of the jet tunnel. The shape is different, the holes in the screw inserts are larger on both the body and the steering nozzle. Just a number of things I noticed that were different that’s why I asked if you have edited the files. I used the link that was provided for the files…. I also am curious about your water cooling pump.

[@Mr.RC-Creator]

@@justinjanes3361 I understand the problem, you can drill a water-cooled inlet hole from the jet tunnel to cool the speed regulator as well by drilling it in line with the area where the impeller rotates so that the pressure from the impeller pushes the water out. www.aliexpress.com/item/1005002635958696.html?spm=a2g0o.detail.1000023.15.12667b5eQ8h7eV

[@sergiosanchez_09]

Hello, I want to make a boat like yours, but I don't know what materials to use. Could you send me a list with all the materials?

[@Mr.RC-Creator]

Sorry for my rate reply. Required Material PLA+ ballbearing 10*4 2 Drive shaft 4mm Cooling nozzl M5 Water Cooling Silicone Tube 2 Rubber Bellows Seals Pipe Fitting Connector Water 6mm Havefan.!!! ☺️

[@celedoniotourinodelrio7388]

Que medida son los rodamientos del eje

[@Mr.RC-Creator]

2 rodamientos de bolas de acero inoxidable para eje delantero y eje central 9x4x4.😁

[@MentalDashrc]

Puedes compartir el STL?

[@Mr.RC-Creator]

I have a link on the top

[@sareefv]

STL files please..

[@Mr.RC-Creator]

Link www.thingiverse.com/thing:5424311/files Have fun. 😁