433Mhz Garage Door Opener - Universal Remote - Easy How to Program

If this one does not work try:
• How to copy 433MHz RF ...
or
• How to reset or clone ...
Instructions thanks to IVYb's suggestion
SEE BELOW
In This Video, I show you the simple steps to firstly reset your garage door remote and then show you how to program it. Simple step by step garage remote how to guide.
Steps:
================================
|Clear existing Memory Settings|
================================
1. Hold down the A & B Button (the two closest to the LED Light)
2. While Holding down Button A (Left) Press (Slowly) button B -right one, 3 times
3. Then Release Button A.
Now no button presses will operate the light (LED)
================================
|How to Set New Learning Code |
================================
This is a 2 Stage Process:
=========
|STAGE 1| Programming New REMOTE
=========
1. Get old door opener and the new non-programmed one close to each other
2. One the old Remote that works, hold down the button that works on the door
3. Now Press and hold the button (The LED will Flash a few times and then be raon the new remote you wish to operate your door with.
4. Hold this button down until the LED light goes Solid
5. Stage one Complete
=========
|STAGE 2| Syncing to Door Master Controller (If Above does not work)
=========
1. Put Garage Door Master Controller into learning mode and wait till it is in listening mode (Each type is different = refer to your owners manual) and then press the button you have configured.

[@sticustom]

Thanks mate. You made my life a lot easier. Just read the instructions and they made no sense at all. I got the remote to work as I watched your video 👍🏻

[@skunk_workx]

Best video for getting these remotes working, thank you.

[@olivierdescargues]

thanks . had the same problem . remote has been laying in the car for 6 months . now working thanks to you. cheers

[@coolguyindeed]

Same.. I have mine for years. Until now i really need it for my remote car replacement. The instruction to clear the code is different from other videos i've found years ago. Once again, thank you sir westy 👍

[@matjaztrebovsek7119]

Thank you! Your video brought me further.

[@PaulBeausang]

Tried 3 different videos - the approach shown here was the one which worked for me. Note that the approach was different from the instructions provided with the remote. Video is really clear and specific on steps needed and how you know the programming is working - i.e. what LEDs flash and when. Really useful - many thanks

[@rent2ownnz]

Appreciate the feed back, am really glad it worked for you. Took me a long time to figure it out by trial and error.

[@saskiajonker9247]

Thanks for this, instructions were vague but got the remote to work thanks to your video!

[@brianpeterson113]

Thank you. I never got a manual when I purchased these. This video is very helpful and they work great. Thank you for the 411.

[@rent2ownnz]

Most welcome

[@shaun.oo__oo]

Champion, I was following OEM instructions and nothing was working till I saw your video and cleared the remote. Followed OEM instructions again and boom... working remote 👍

[@rent2ownnz]

Great ... MAybe you should share you one that was not working here and I will add it into my intro speel above, may work for the ones that my method does not work

[@shaun.oo__oo]

@@rent2ownnz I didn't make a video mate, all good your video was what I needed to do 👍

[@mailantrinh9623]

Thank you for your instruction. My remote finally works now 👍

[@alfilart]

I watched many videos and this is the one that works. Thanks!

[@maasis8]

Thank you. Very helpful.

[@rachaelmoore3673]

Perfect - worked first time with my NECo key fob. Saved myself £40 😀

[@rent2ownnz]

Nice one! good stuff :)

[@vspeaight]

Thanks for the great and easy to follow video. Set mine up in minutes after watching your video. Works so well. Thanks for taking the trouble to make this very helpful video. Australia

[@rent2ownnz]

More than welcome. Glad it helped.

[@michaelfaers8757]

Having real problems until I watched your video, all sorted now, many thanks

[@yves2348]

Mine persist, I had loads of them. This china crap sucks.

[@corkfella]

Super work brother . Saved me a tonne of time. Big ups from Ireland 🇮🇪

[@rent2ownnz]

Great, glad it helped you out.

[@francotabone4047]

Hi, thanks a lot for your video and it has been very helpful as I managed to clone it perfectly. Thanks again.

[@civramatt]

Thanks this really helped and it worked perfectly.

[@dentemaxaustraliandentalla4003]

Thank you so much. Much appreciated 😊

[@byjingobob]

Cheers Westy, I was getting close to the end of my rope! Now working perfectly thanks to your video.

[@gnat2006]

Thanks, you saved the day.

[@johnsgalv]

Thanks man, finally got the bloody thing running 😀

[@AurelijusBanelis]

Worked with 4003 Rev2.1 🙂. Note to release B and click three times was the main issue I had. Was able to clone from TX3312 B1.0. Thanks 👍

[@opsahle2]

Thank you so much! I managed to get an universal remote from Aliexpress (not the one you show here) up and running thanks to your video. But strangely: All four buttons seem to be programmed now, but only one is doing anything - and it is NOT the one I pressed during the cloning process. But the main thing is that I now have a working clone!

[@hrcivic]

The best easiest tutorial i ever seen. Thank you very much

[@charliedrake247]

Great job thank you for your help.😊

[@MrSulitariu]

thanks mate for the help!

[@GrimmReaper7165]

I saw another vid that showed how to clear out the program but it didn't work. Yours did! Thank you so much!

[@rent2ownnz]

glad it helped you out

[@ASousaMakesIt]

Thank you! I just did it and worked like a charm!

[@rent2ownnz]

I am glad.... Yep I struggled to find the way to do it ... so figured it out and shared it so you all can get the benefit. hope you liked and subscribed

[@GustavoHenriqueRuffo]

Thank you, Westy. Saved my day, here.

[@ggazzara1115]

Thanks for posting a video that actually works for these remotes! I really appreciate all of the research that you did to figure this out too.

[@rent2ownnz]

Thanks for the review. I am happy it worked for you. CHEERS WESTY!

[@HerkulesNorsk]

Worked!! Thanks

[@rorybrennan6828]

Loving the content westy!

[@rent2ownnz]

Thanks my man

[@wanzi57]

Many thx 4 this instruction

[@gazoo8316]

Only video that worked for me👍🏻 thank you 🙌

[@maccsamillion3158]

Thank you!!

[@MegaFoster86]

Thanks, it's work for me

[@beeldbuijs1003]

Thanks. Two additional tips: Mine would stil not open the garage door, despite the led blinking confirmation. Turned out there was a tiny piece of bare metal wire broken loose from the solder on one side, on the back of the new remote. I soldered it back and now it works fine! I had to 'tune' to the right frequency by turning the tiny screw on the bottom right first though. :)

[@simonkirton8521]

Just wondering before I pull my elderly neighbours remote apart can you actually change the frequency on these remotes if that’s what I take ‘tune’ as or you just having a laugh

[@LegendLength]

@@simonkirton8521 I believe they support 2 freqencies, 430 and 320 or something like that. So it's likely some kind of binary switch.

[@nothere9551]

I got a couple I had trouble programming them too. After a year still going strong.

[@rezahar]

Thanks a lot. It was very useful for me to copy my garage door remote.

[@casimir2926]

it works, thanks

[@giannisk7658]

Thanks a lot brother from greece

[@rent2ownnz]

No problem😉

[@janiszeltins1917]

Great! Thanks a lot!

[@oompa_loompa5943]

Bloody legend mate❤️

[@jacksonbrazzale831]

Thank you Westy! Great vid, very helpful.

[@alexisdante1061]

i realize it's kind of off topic but do anybody know a good place to watch newly released movies online?

[@jadrene4678]

@Alexis Dante Lately I have been using Flixzone. Just google for it =)

[@jeffersondavid5679]

@Jad Rene Definitely, I've been watching on FlixZone for since march myself :)

[@alexisdante1061]

@Jad Rene Thank you, I signed up and it seems like a nice service :D Appreciate it !

[@jadrene4678]

@Alexis Dante no problem xD

[@ministerioarmsful]

Thanks a lot it was very helpful 😊

[@rent2ownnz]

Glad it helped you out!

[@johnruru2706]

Cheers mate for your help. Good video, great help👍👍

[@q4qatar921]

It helps me alot 😍😍😍

[@SenorNav]

Thank you sir, your method worked great in New Zealand. Jai hind

[@declanjoyce8640]

Yep...this works, just ended 6 months of faffing about with other remotes...(but there again I am a slow learner!)

[@rent2ownnz]

Lol, life is about learning. pay it forward :) Glad it worked for you

[@alessandrop7621]

VERY NICE THANKS

[@csikiandris]

Köszönjük!

[@VvDarkFoxVv]

Man You're a freaking Genuis, Thank you !

[@colinjefferies4072]

thanks a mill..

[@emiliomota2459]

You really helped me out man

[@rent2ownnz]

You are more than welcome. Glad it worked for ya

[@Araian85]

Thank you. Mine came without instructions. Works perfectly now.

[@rent2ownnz]

You're welcome!

[@richardtonge1921]

Great tutorial, thanks for taking the time to upload this video and helping people. After following the clear instructions I managed to program 2 replacement fobs.

[@rent2ownnz]

Nice one ! Great Job Thanks for the like!

[@laneyallan9847]

Thank you!

[@jeso317]

Great vid, mine works great. Would you consider a video on how to change the battery on this badboy?

[@pashadiesel7808]

thank you! you are awesome!

[@junkyardompp5512]

Thanks 👍🏼👍🏼👍🏼

[@stephanoscharalambous5273]

perfect!!!!!!

[@adrianhendricks9470]

I got the same remote as in the demo. I programmed it up and it works. I had to hold the remote one metre away from the opener, cos the remote batteries were so flat. Off to get some new batteries.

[@DavidJohnston58]

Thanks, that got it going. But A would only open the door so programmed C straight after in same way and now A opens and C closes, I'm happy with that.👌

[@rent2ownnz]

Cheers. Maybe your door master controller memory is full. you can clear it and start from scratch. should work. KZbin it :) I think I did a video years ago that had how to reset and clear the master controller memory.

[@gilrotem10]

thank you, Australia

[@Ludikhuyze]

This one works for me. The other when you have to pouch a and b together not. Thanks!

[@rent2ownnz]

Glad it worked for you :}

[@lebotsh7022]

Thanks alot

[@imtheboss8414]

Can i program the RC like when i press A to open when i press B to close ?

[@StillWater426]

Hi Westy, nice video, really ahndy, can you give the link where did you buy those Garage Door Opener - Universal Remote?

[@edamamebiru3960]

Thanks for the video. If I don't have the remote, can I buy one on eBay and ask the owner of the garage door the provide me with the frequency and a code? But, then, how could I program myself the remote? Sorry, lots of questions.

[@Ozibits]

thanks work perfectly now. I was about to throw them away

[@rent2ownnz]

yeah Me too … and then I sat down and figured it out and thought I would share with the community! Glad you liked it.

[@coolguyindeed]

@@rent2ownnz thank you sir... Thank you very much 👍

[@sinatiom]

Tnx

[@gio_anvi]

Hi, I did it but when I press the button to open the garage is not working, you said something at the end but I didn’t understand, something with the motor? I did the same with a car remote control and works, but I’m not sure why with the garage is not working

[@xray364]

Hi, anyone know what to do when the key doesn't reset properly. I've got a 3 button which is exactly the same. I programmed it ages ago and I wanted to reset it but I forgot the instructions. I thought it would be the same process by no luck unfortunately. BTW, when I open the key to reveal board and battery, it actually has 4 programmable button, but only three on the outside. Not sure why they hid one of them

[@yuvaldanker8869]

Thanks

[@rent2ownnz]

Welcome

[@logankelsall6389]

Is it the same process for a gate remote to.

[@paulsgreatdane]

Great video mate! I followed the instructions that came with the remote and it didn't work. lots of looking around before I came across your that works cheers 🇬🇧

[@waltermelon5672]

Thanks so much. Lifesaver ! In my case I only got one to work. The other would not reset . The button solid Flash after reset on every button . Edit : got it to work. Must be something about the timing issue with resetting

[@rent2ownnz]

must be kaput ... probably a broken wire

[@denis8321]

Is there any possibility to erase the code from the original remote when programming a new remote? I have only one original, and I don't know how to reprogram again if needed. 🙄

[@samanthastubberfield8975]

I followed all instructions and it shows that my remote is linked. But still doesnt open garage. Have tried doing it on the actual garage door as last part instructed. Flashes as if synced. But still doesnt work 2 open garage :( please help.

[@mrkiss3]

Bought this type of remote firstly the case doesnt close after you install the battery and either way couldn't get it to reset

[@M.D2419]

Where you buy it

[@keZZaZ84]

All well and good if it flashes 3 times but what about when the light just flashes rapidly when pushing A and B

[@headgon]

Hay any tips I did what you did it didn't work so tried to program of the main unit but that didn't work either maybe duds?

[@rent2ownnz]

Not sure ... have a look at some of the previous comments there are a few methods to do these units.

[@MrSandshadow]

Hi, by any chance do you know how to fix codes on this beauty : A036 Four-button Controller Copy Type Remote Control Garage Door Switch - BLACK ? Cheers!

[@Msopasniful]

Hi all, i cant erase function. Press a and b together but dont stop blinking. Is there any solutions?

[@14713552]

Thanks 🙏🏼 so much I bought the exact same remote and all buttons flashes and now its all good peace

[@rent2ownnz]

great! thank you.

[@scottellis4785]

Hi there, I seem to be having issues with teh second part "go into the garage door operation unit and put it into learning mode, then once you have done that press the button and booyah!" How do I put the door unit into learning mode?

[@ishbhad]

On the back of the box unit which hangs on the ceiling of your garage door you’ll see a button which says” learn” . That’s what he is talking about

[@patrycjaradecka950]

Hi, not sure if someone has the same issue. I have the same garage fob, but a few weeks after programming it's not working and I have to do the programming again. I even bought two and they both lost programming at the same time. Does anyone know what could be the reason?

[@dianazamfirescu359]

Hi. My remote is continuously flashing and no combination of keys can stop this. Do you know what i can do?

[@AEROSOLKID1]

Yo!! Like the video but HTF do you get 'em cleared of factory code? I have tried pressing A & B simultaneously but the light just continously lights intermittently.

[@joriiiiii]

Same problem here, still looking for a solution...

[@mishjames]

I had two remotes for this model one was stolen out of my car, if I follow the guide above, and reset the existing remote, will the stolen remote still work ?

[@rent2ownnz]

Hi Michelle, Very ... very good question. What you can to is clear all the previous saved configs in your door controller. then add your new ones! that should solve your problem.

[@BuzzyBee11]

lol the old kiwi talk.... 'prrrrrrr it in' @ 3:07

[@digger5521]

Will this work if I don't have old remote it's missing it's a b&d roller door pretty old school mate

[@rent2ownnz]

Open your B & D MAin Module in your garage and see if it has the frequency on it ... should be 433Mhz if not ... get which frequency it is and then get on online and follow the same set up. you will be able to clear all previous paired coeds and set a new one. Look up your model specs online and you should find a manual that works.

[@applebeetea9301]

Could you make a tutorial to replace the batteries for this exact model? Thank you

[@rent2ownnz]

Hi There, Which model? the old one? or the new one?

[@ArthurvdHorst]

Really happy I came accross your video but this still didn't work for me as my garage control unit does not recognize the new remote. Which is the same remote as the one you have. Also my garage opener is a Chamberlain but guess a different model from yours. I got a ML500. Any suggestions or is it perhaps that this remote will simply not work for this model?

[@rent2ownnz]

Hi There, Try doing to the Door opening controller (On the door itself) and press your buttons on the remote.... can you see the light rapidly flashing on the control unit? if so, it is seeing your remote , but just needs to be #CODED# into your controller. try the last part of my instruction on how to do that. - see how you go

[@ArthurvdHorst]

Westy's How To Guides Thank you for your reply. I have noticed that when I use the original remote the LED on the control unit flashes rapidly but it does not flash rapidly when using the new remote. I guess that answers my question then, the control unit does not see the remote. Will have to look into another model.

[@rctrix9063]

Yep Nar, the clear out bit works but the learning bit was a flop.

[@rodneybradbury2880]

Hi Westy i tried everything you have in the video but still not work i have a merlin garage door any other ideas i could try thanks Rod.

[@rent2ownnz]

Hi Rod, is it the correct frequency remote for the door itself?

[@kurtbruns8102]

Tried it step by step but still can't stop all lights flashing? Any idea Why?

[@kidda74]

Got mine to work thanks to your video, but the range on it is crap. I have to be almost on top of the garage door mechanism for it to work? The original one still works from metres away?

[@rent2ownnz]

faulty remote

[@JoseMaria-dq4ir]

Thank you very much ... I've cloned mine