I feel like the amount of work you did in just this video is more work than I've done in my entire life. I never could have figured this kind of crap out. Amazing that you can do this.
@PostalRedneck2 жыл бұрын
I have never had a shift solenoid fail on me and could hardly find anyone who has had this problem so I figured I would do a detailed video on it. I kinda enjoyed this fix.
@JoshJackson13 Жыл бұрын
You made a great video. My 2001 pathfinder got stuck in 3rd this morning when I first cranked it up drove it 5 minutes reverse worked fluid was full then I turned it off started it back and it went back to working fine
@JoshJackson13 Жыл бұрын
My oil cooler pump seal started leaking few months ago so I may be getting oil on my plug while I'm driving. I need to crawl under it and see
@PostalRedneck Жыл бұрын
Thanks. It could still be the shift solenoid as well. Running it in reverse might have heated the fluid up around it enough to get it to start working. Either way you found a way to get it working again so you can drive it a bit more before having to service it.
@JoshJackson13 Жыл бұрын
@@PostalRedneck yeah I have really low idle sometimes when I start it cold if the choke doesn't come on. if adjust the throttle it's really high when the choke comes on. Maybe it just didn't have enough battery power that day. I have ran it about 3more days and had no problems.
@PostalRedneck Жыл бұрын
Yeah thats good news and scary at the same time. I would be worried about getting stranded again. Im happy mine acted up where it did and when it did. I just got done doing a gambler 500 event and was all the way on the other side of the state the day before.
@007outtacontrol6 ай бұрын
On@PostalRedneck I have a 02 2500 HD and it's only going in 3rd gear. Even if k drop down to 1 it's like it's skipping D all together...
@mrkeopele Жыл бұрын
yes, troubleshoot before buying parts, good job friendo!!!
@PostalRedneck Жыл бұрын
Finding the problem is the hard part. Getting new parts and installing them without knowing if the parts replaced were bad to begin with is not a good way to fix a vehicle.
@johnnyshell283911 ай бұрын
I'm glad that worked for you. I just did mine today. Same reason. Installed 2 new ones. New filter and new fluid. Still stuck in 3rd
@boggycreekmafia812411 ай бұрын
Same here. Bout to start chasing ground wires
@johnnyshell283911 ай бұрын
@@boggycreekmafia8124 oh yeah. I'm starting at the harness and working it back to the fuse block then to the ignition. After that I don't know
@boggycreekmafia812411 ай бұрын
@@johnnyshell2839 all the forums I’ve looked at said start at the Ecm
@boggycreekmafia812411 ай бұрын
@@johnnyshell2839 I've seen this afew times in the shop you should splice in to the ground wire in the harness going to the transmission and run it to the battery ground if this solves your issues you will need to run the wire to the ground on the em and solder the connection and cover with heat shrink. Bad grounds on these 4160e units make them do things not in any manual you have ever read. 3rd gear is the give away that you have a ground issue, it's not electrial. The ground wire in the plug is pin "E" it is located to the front on the truck when the plug is in the transmission the wire is white remove the cover on the top of the plug and you will see the letters for each wire, splice into "E" and run up to the battery
Aw shit you were at tip of the mitt too? I thought it was absolutely awesome this year, so much more and better off road driving than the Detroit gambler. Good thing you didnt have any issues on the gambler, I had a cv joint break on my 4x4 safari van (I had the "stock" height one, i know there was a guy with a lifted astro, wish I would have gotten the chance to talk to him.) But the cv wasnt completely broken apart so I drove it 300 miles back home with the cv sounding like a meat grinder, hell I'm still driving it while waiting on parts to be delivered. A trick that I did with transmissions with no drain plug is disconnect a cooler line and put a hose on it into a bucket then start the car and let the transmission pump all the fluid out into the bucket, this is best done with 2 people because that fluid can really shoot out of there
@PostalRedneck2 жыл бұрын
Yeah the Detroit Gambler is not that fun. I skipped it this year. Tip of the mitt is way better. I did get quite lucky that it didnt break on me during the event. I carry an extra used cv shaft as they are a week point in most off road vehicles. Glad to hear you made it home what how bad it sounds it was. I have done a few transmission flushes doing that trick with removing the cooler line and sticking it into a bucket. Its not a bad way to do it if you have hose laying around to use.
@pierorossi56087 ай бұрын
Hi, i had the same problem but we changed all the selenoids and the problem persist, could be any wire cutted?, i cleaned all
@pierorossi56087 ай бұрын
We did a bypass and the problem persist too, im kinda thinking that could be de vcm
@PostalRedneck6 ай бұрын
Did you do a resistance check from the plug like I did. It could be a bad harness inside the transmission.
@pierorossi56085 ай бұрын
Yess, actually we changed, all de wires inside the transmission
@davidrusscher502 жыл бұрын
Glad it didn’t happen while we were on the tip of the mitt gambler 500😁
@PostalRedneck2 жыл бұрын
No kidding. We got supper lucky.
@whatdfukk11 ай бұрын
Excelent video, Thank you!
@PostalRedneck10 ай бұрын
Glad you liked it! Such an odd problem.
@latinpaver Жыл бұрын
Very good video
@PostalRedneck Жыл бұрын
Thanks
@SteadyRollinn Жыл бұрын
Mines feels like it’s in 3rd gear all the time when I put it in drive but if I manually shift it from 1st to 3rd it shifts do you think the solenoids could be the problem ? I have code p0758 It’s a 06 Silverado
@PostalRedneck Жыл бұрын
Same thing mine was doing. I would have to say you are going to have to replace the solenoid. I would recommend doing both at once as you are already in there.
@AmilcarSomarriba2 ай бұрын
👍👍👍
@PostalRedneck2 ай бұрын
I take it my video help you :)
@wking5232 жыл бұрын
Good information
@PostalRedneck2 жыл бұрын
Thanks
@1kabraham170 Жыл бұрын
I have a 2006 Chevy Silverado and it stays stuck on 3rd gear? Do u think is the transmission or something else ?
@PostalRedneck Жыл бұрын
Have it scanned and if the same codes come up more than likely you have the same issue. This unfortunately is not horribly common but it does happen. One simple thing you could check to see if the plug to the trans fell off somehow. If a transmission is unplugged it will be stuck in 3rd as well. Good luck.
@markmulder4434 Жыл бұрын
My sons transmission 4l60e won't go into 3rd and 4th any idea what that maybe
@PostalRedneck Жыл бұрын
Here is a good video explaining the 3 most common failures. kzbin.info/www/bejne/d4fNgaeGbcd5rpI
@andyvaldez28303 ай бұрын
Thanks for the detailed info! I keep getting the P0758 code on my 2005 Denali. I tested both the A and B solenoid and they both read around 22 ohms. I randomly lose first and fourth gear but it's not consistent and the CEL will come on and go off on its own. Sometimes I can drive a hundred miles with no issues. Other times the transmission will start acting up within 5 miles down the road. Any idea what I should look at next?
@PostalRedneck2 ай бұрын
I would replace both solenoids and the harness in the pan. Its hard to fix a problem that is not consistent.
@brentmooy4807 Жыл бұрын
What was the original shifting problem?? You replaced faulty B so that would be shifting from 2nd to 3rd would go to neutral ??
@PostalRedneck Жыл бұрын
Truck had Park, Reverse, Neutral and 3rd. Didn't matter if you put the shifter in 1st, 2nd, 3rd or drive it would take off in 3rd gear until you got up to a fast enough speed for 4th gear then it would shift into 4th. You could drive the truck the way it was but taking off from a stop was very slow going and the truck was not happy. Im guessing if you had to stop and take off a lot you would burn up your trans quit quick but you would be fine on the highway once you got it going.
@jsbird9810 ай бұрын
Hey awesome vid, did a ls swap into my obs and damn if its going from 1st 2nd 3rd just fine but then stays in 3rd unless I put it in reverse or park (p key off that is) other than that it stays in third. I can manually shift to 2nd but not first. Im leanin to replacing these what do u think?
@1UglyObs6 ай бұрын
@@jsbird98you figured it out having same issue
@jsbird986 ай бұрын
@@1UglyObsNope I repinned the harness a few days ago and will be installing it tomorrow on my day off with hope it will fix the issue 😅
@1UglyObs6 ай бұрын
@@jsbird98 let me know how it goes brother
@klumsytone2 жыл бұрын
Would it be a good idea to replace all solenoids as preventative maintenance? If so, how many solenoids total?
@PostalRedneck2 жыл бұрын
I have never had one fail on me but if you are doing a trans filter and plan to keep the vehicle for a long time it might be a good idea. Mine had 280,000 miles on it. There are 4 solenoids all together. 1-2 and 2-3 that I replaced. The other 2 are 3-2 and TCC. Honestly I wouldn't worry about it too much but once again its up to you. The main thing I would tell you to do to prolong the life of a 4L60E is to get a better trans cooler. These tend to get hot and that is what usually takes them out.
@budmanzoom4441 Жыл бұрын
Smart! 😃
@PostalRedneck Жыл бұрын
Thanks. Hope it helps someone with the same problem.
@haronjowi Жыл бұрын
My automatic transmission Toyota TZ 90's series is also stuck in 3 gear. Could solenoids be the problem or it's much worse?
@PostalRedneck Жыл бұрын
Not a clue. I would recommend taking it to a shop and having them look at it. Every vehicle has different operations in the transmission.
@pxte.70078 ай бұрын
My trucks solenoid was marking the shift solenoid as well intstalled them and same problem all gears work for like 2 minutes than it’s stays in 3rd gear I can manually shift to 2nd gear but it won’t go into first nor 4th
@PostalRedneck8 ай бұрын
If I remember right I could manually shift to 2nd as well but I also had 4th. I would check to make sure you dont have another bad shift solenoid once the vehicle warms up. Are you getting the same code as before?
@mrkeopele Жыл бұрын
my 2001 Suburban 4x4 just today started not wanting to upshift, no SES, no codes that I can see. I've already had intermittent service 4WD, and was going to get to that, unfortunately today when I went to go see neighbor it was in 4Low, and after the offroad portion ended of my run ended and I got to pavement I noticed high rpm's, drove to Post Office trying to Isolate symptoms other than the transfer case not shifting, it was DRAMATICALLY HANGING IN GEAR BETWEEN SHIFTS, and would only upshift after coasting, but mostly hanging in 1st too long and 2nd too long, not sure if it was getting into 3rd and4th at all, kind of hard when in 4Lo. Any clues as to where I should start?
@PostalRedneck Жыл бұрын
I have always noticed with my truck in 4low that the shift points all seem to drag out and dont want to shift as well some times. I would try to get it into high range and see if the problem continues. The computer has all different shift points and rpms it shifts at when in low range.
@mrkeopele Жыл бұрын
@@PostalRedneck I have the Tow/Haul package, and I was pleasantly surprised when i tried it, to feel like the good old days when we put B & M Shift kits in autos for the tighter shifting! I have not noticed any difference in shift programming when selecting the different drive modes on my 4 button dash controller. Only noticed the different shift programming when I use Tow/Haul option. I really appreciate any interest your showing in my situation. As a retired Elevator Technician I'd rather use point to point troubleshooting than the "Shotgun" approach they called it when guessing by throwing parts at the problem. Getting all the data needed these days to do Point to Point troubleshooting is sometimes challenging.
@PostalRedneck Жыл бұрын
I would try to address the 4x4 problem first if its getting stuck in 4 low. Im not one for throwing parts at a vehicle either. If the 4x4 button is not lighting up and blinking when selecting what you want typically its the 4x4 switch that is bad. If you select a drive type and it blinks but nothing happens then its probably the 4x4 actuator motor. As for it not shifting into gears the 4L60E is a problematic transmission that has plagued the chevy community for years with weird problems. I would check the fluid and see if its dark or smells burnt. If either is the case it probably needs a good rebuild and flush.
@mrkeopele Жыл бұрын
@@PostalRedneck what would help me now is if you had the wiring pinouts for my TCCM, 4 button dash switch, and the Shift motor connectors. with that I can isolate where the electrons have encountered a hurdle to big to jump!
@mrkeopele Жыл бұрын
@@PostalRedneck Got It. Manually switched Transfer Case out of Low, had to realign the shift motor, but you were right, it is shifting normally now. Smelled like my Shift motor might have got hot, I couldn't turn it manually, had to take it apart to align it. Thank you
@mikeh50397 ай бұрын
Fix the drain plug 😂
@PostalRedneck7 ай бұрын
Never! Its a $300 Tahoe with a broken frame. It has more problems than a drain plug haha. More than likely getting scrapped at the end of this winter.
@monzimusodinson15216 ай бұрын
How do you reset the ABS light
@PostalRedneck6 ай бұрын
There is no reset for ABS. You must have a problem with your system somewhere.