Well explained. should've brought up the notches having to line up. Just a quick tip** The digutal display when lined up properly will show an underline of the position it is in. If the line under park or buettal isn't there, The reading is invalid and will cause a no crank condition due to the fact it doesn't see the position it is In. 🤙🤙
@GregHuston5 жыл бұрын
SO glad you posted this! I was messing with the shift cable for HOURS and finally decided to take a look at this part and see if there was something that could be awry with it. Sure 'nough this is my EXACT problem. I have P>2 and N has 2 positions on the indicator, but I have all gears just the display was messed up.
@thisisyourtransmission5 жыл бұрын
Your welcome
@electech_54952 жыл бұрын
Cool man! Glad to see someone else did this! Ive been planning on doing this with epoxy, right after I fix the connections lol
@trevorcline60954 жыл бұрын
YOU MUST FILE THAT SHAFT BEFORE REMOVING THE SWITCH!!! THEY COME MUSHROOMED FROM FACTORY AND REMOVING THE SWITCH WITHOUT FILING THE SHAFT WILL VERY OFTEN TIMES RUIN THE PARK NEUTRAL SAFTEY SWITCH 🙂👍
@thisisyourtransmission4 жыл бұрын
You are right, however I havw gotten some aftermarket switches that were too loose, looser than the poem switch, and some that have worn over time
@ProfessorCockrum3 жыл бұрын
What a great video of a really good fix
@tnwilson10503 жыл бұрын
That would certainly work for a while until a seeping seal works the glue loose and it falls off. Use a wirefeed and build up the keyway on the shaft itself so it takes all of the freeplay out of the mechanism. DONT WELD THE SHAFT WHEN IT IS IN THE TRANSMISSION. The heat will destroy the oil seal behind it and create unnecessary heat. It is fairly simple to remove the entire assembly away from the transmission if you remove the pan.
@naturehealthandtruth96722 жыл бұрын
What does using a "wirefeed" to "build up the keyway" mean?
@johnward58902 жыл бұрын
I have a problem something like that but my shaft is moving to much on the inner linkage spur inside the transmission pan. It either the pin or the spur that is wore out, i guess it would be called to much back lash where the spur mounts to the selector shaft that you are gluing, but on the other end of that shaft. It makes for a very sloppy shifter but all the lights on the dash work fine, it just doesn't want to shift through all the gears properly. This could make a mechanic think the Transmission was mission 3rd and 4th gear if he didn't open the Bottom of the case and look at the shifter spur on the inside. Park is from P to Neutral, D overdrive is as fare as the shifter will go down around the 1st gear spot on the dash selector section This really screws up the neutral safety switch and the Computer on a 1998 K1500. Just something to look out for.
@ronaldpowell9615 жыл бұрын
My 05 Silverado loses all gears but I can shut the truck off and restart it then I can put it into gear and drive off could it be the same part
@swrvn62c63 жыл бұрын
I have the same problem. Did you ever figure it out?
@HectorsCarAudio13 жыл бұрын
Same here just rebuilt a 4L60E no gears , nothing ....?
@stetsonstrawn24513 жыл бұрын
@@swrvn62c6 same here did y’all figure it out?
@waltercardenas73544 жыл бұрын
Outstanding video. I have a 1996 Chevrolet Silverado and when I put in park I like if it was a neutral. Any help would appreciate. Thanks
@thisisyourtransmission4 жыл бұрын
Need more info. If you put a vehicle in park, it is considered like neutral, so what do you mean?
@OKBAOK3 жыл бұрын
Hi, Thanks for the great video :) Quick question, before doing this, should you put the gear on the dashboard on Neutral position? so that the cable is on neutral length? when you install the switch is on Neutral and the shaft is on neutral position.
@thisisyourtransmission3 жыл бұрын
Yes
@charlesjimenez6675 Жыл бұрын
I read that if you set it in reverse and switch the N.S.S to reverse it would be better and a more accurate to bolt in position .
@Good-Enuff-Garage5 жыл бұрын
I appreciate the video but I would not trust super glue to hold a dirty metal piece to a flimzy plastic piece for very long
@thisisyourtransmission5 жыл бұрын
There is a glue called qbond. It is supposed to work.
@koshnaranek23174 жыл бұрын
JB weld much better for this.
@driverozzko4 жыл бұрын
I have a 05 trailblazer with this transmission. Yesterday I left the grocery store and took off from a light and it was like the car was in 3rd gear. I pulled over and put it in park. Pulled the shifter back into drive and the same thing. Like it's in 3rd. So I put it in reverse. Backed up 2 feet and stopped abruptly. Several times I did this. No change. I limped it home. Today after work I jacked up the rear and put it in 2wd. Started the car, the rear wheels spin forward in every gear including neutral and reverse. Even acts like it wants to pull forward in park. Any idea on what's going on here? I installed this rebuilt transmission a year and a half ago myself. No problems until now.
@thisisyourtransmission4 жыл бұрын
Sorry no response, have been busy with this pandemic mess. Did you get your vehicle fixed?
@driverozzko4 жыл бұрын
I replaced it. I removed the pan and found a bunch of metal shavings. I believe the sun shield broke. I kept it. Have it on the bench in the garage. I've wanted to rebuild one for a long time. I've had the trailblazer for 3 years and have installed 2 transmissions in it already. Lol its time to learn how to fix em.
@cdurch15 жыл бұрын
Thanks for the video, im about to replace the range sensor (nss), im told that is the reason my reverse lights stay on, even after i turn the car off and pull the keys out?
@thisisyourtransmission5 жыл бұрын
You're welcome
@ericcm69362 жыл бұрын
You absolutely do not have to add super glue to this. The switch is mildly adjustable. If you tilt the switch clock wise or counter clockwise the plastic teeth will butt up against the teeth on the transmission lever and "slop" will be removed. Also within the switch is quite a large "safety" area where it will and will not allow start. 99.9% of the time, a quick install will work just fine and that tiny bit of play will not matter at all, if it did, the great "allison" trans designers wouldn't be so great.
@thisisyourtransmission2 жыл бұрын
No one is perfect. This is why car manufactusrers have recalls. Over time shafts wear thin. Another thing, aftermarket parts are not always made true. As a result modification is necessary at times.
@ianwilds31394 жыл бұрын
did you file the shaft before installing? These shafts are mushroomed from the factory and must be slightly filed or it will ruin the new switch.
@thisisyourtransmission4 жыл бұрын
Never filed the shaft ever in many years. The only loose ranges switches have been aftermarket ones. Original equipment switches fit tighter. I will check for what you say about mushroom shafts closer. However, I have never seen a mushroomed shaft. Also, I have seen switches that have never been off that have worn out on the shaft and become loose.
@trevorcline60954 жыл бұрын
Its quite difficult to see the mushroom, but it is there. You must file the shaft before removing the switch!!
@HectorsCarAudio13 жыл бұрын
Hello Great Work 👍🏼 I just rebuilt a 4l60e , no gears . The scan tool show , current gear 2nd all the time ? Any ideas ? Thank you in advance!
@thisisyourtransmission3 жыл бұрын
Is the vehicle in failsafe mode?
@HectorsCarAudio13 жыл бұрын
THIS IS YOUR TRANSMISSION transfer case was in neutral lol thank you .
@stetsonstrawn24513 жыл бұрын
@@thisisyourtransmission mine is it works sometimes but when I put it in park it won’t work no more
@aheros_life68173 жыл бұрын
Hey i got my nss on .. I cant get the metal piece back on that attachs to the shifter cable any advice
@Wildkat-1 Жыл бұрын
Brass shim-stock !
@electech_54952 жыл бұрын
Smart guy!
@deewaa24fly4 жыл бұрын
Replacing a trans on 04 GMC Envoy. Trans has 2 electrical connections coming off nuetral safwty switch ( same as in this video). But the vehicle has 1 large 11 pin electrical connection going to the nuetral safety switch. Is it as simple as removing the switch with the 2 electrical connections and popping on the switch with the 1 large 11 pin connection?
@thisisyourtransmission4 жыл бұрын
yes, if you can get it off.
@meestameestaaaaaa3 жыл бұрын
i hae a 2006 gmc sierra 4x4. the switch only has one plug in. the transmission i bought for it has 2 plug ins and was removed from an 02 silverado. can i leave the switch i have on my truck while replacing my transmission and just mount the existing switch onto the new transmission?
@thisisyourtransmission3 жыл бұрын
yes
@justo82chevythang25 Жыл бұрын
Well this make you the truck not crank replaced my trans an now its not starting
@thisisyourtransmission Жыл бұрын
Yes it can make the vehicle not start
@bryan22873 жыл бұрын
I have a P0706 code that popped up 2 days ago. I wasn't having any problems until yesterday. 1st, I felt a little skip and then driving in 4th and 3rd was high rpm and no speed increase. I can still drive normal in 2nd and 1st. Any help would be appreciate it. Thanks In Advance.Good Informative channel.
@abdilgalan5253 жыл бұрын
I’m having this exact problem !
@aheros_life68173 жыл бұрын
Nss switch
@aheros_life68173 жыл бұрын
@@abdilgalan525 neutral safety switch and check the throttle body
@crisgarcia65643 жыл бұрын
Im getting same code p0706 but my issue is that while driving on a the highway itll be about 3rd or 4th gear driving fine and then out of nowhere it seems to go in neutral and i have slow down park and but it in drive again for it to get going again but itll do it again
@crisgarcia65643 жыл бұрын
It also only seems to just leave second gear and im not sure if thats from it being in “limp” mode
@jeremyhanna38524 жыл бұрын
Just by a gm a switch that aftermarket crap is the problem and u can only use a gm switch ounce and then it will b loose and u have to file mushroom on the end of the shaft then install a new Delphi switch not junk aftermarket one
@thisisyourtransmission4 жыл бұрын
I did run my finger on the end and it is sharp. However, I still see some that are loose at times.
@Username-ng8jy2 жыл бұрын
I had aftermarket fuck up after 2 weeks. Waiting on oem one. 4 week lead time. Fuuuuuuck
@west21tah4 жыл бұрын
Ok so would this be my issue on a 01 silverado ? Where I parked the truck literally for 5 mins and then came back and I put into drive and didnt move also that metal peice that on it wasnt on my neutral safety switch
@thisisyourtransmission4 жыл бұрын
First, the metal piece is for lining up the neutral switch when it is being put on. Second, You have to check it. You have to have someone put it in gear ( with the truck off ignition on) an see it the switch is loose on the shaft.
@stetsonstrawn24513 жыл бұрын
My truck does the same thing what could it be?
@corylong95585 жыл бұрын
quick ? does this solenoid have to be working properly for the trans to work.. I lost my gear indicator lights on my dash and my trans stopped working. bought a used trans installed everything indicator lights on dash where back on like normal and the trans worked as it should until the shift cable broke and my indicator lights on dash went back out n trans stopped working completely again.. dropped driveshaft to prevent getting ran over took everything off shift rod and shifted it manually all gears spun driveshaft but after installing it back to rear end and repeated same steps I had no change in results and still no indication lights on dash.. does that sensor stop the trans from operating completely???
@thisisyourtransmission5 жыл бұрын
No, this sensor does not stop the transmission from operating completely.
@alphathefirstone12224 жыл бұрын
@@thisisyourtransmission great video..so if the nss is NOT needed for the 4l60e trans to work can this nss be deleted from the wiring harness and run the engine and transmission w/o the nss ??? I am having trouble getting my ls 5.3 to run and code p0707 keep showing says it the nss ..can I delete this nss and drive okay ??? Thanks
@Al-mp7fv4 жыл бұрын
Does the RANGE SENSOR have anything to do with shifting 2nd to 3rd gears, I have a 1999 Silverado it only drives in 2nd gear but it does shift to 3rd while driving. It does take higher RMP's to shift.
@charliegarcia67333 жыл бұрын
I have 96 2wd Tahoe truck turns on but when u shift it into gear no gears engage,would this be the issue
@thisisyourtransmission3 жыл бұрын
You first need a scan tool to view the indication. One thing that is important in fixing these vehicles today is having the proper equipment to fix and diagnose them. If it is showing the gear on the scan tool, then it could be something else.
@tengzturiagaiii31854 жыл бұрын
Hi, i have a 1999 bmw 323i with a gm transmission. The safety mode with the gear with this ( ! ) inside the gear is on. Then the traction control light in on as well. Do you have any suggestion on what seem to be the problem?that switch that you replaced in the video, could that be the problem? I saw someone made a video here on youtube said that he has that problem and just replace that switch. But i’m trying to ask a second opinion. That switch is a bit expensive to make guesses
@thisisyourtransmission4 жыл бұрын
First, how did a gm transmission 4l60e get inside a bmw?
@tengzturiagaiii31854 жыл бұрын
I bought the car. And they have replaced the motor from 323i to 328i and even bmw dealer parta dept. would ask you if you have gm tranny or zf.
@Highcat273 жыл бұрын
I’m ready a code 28 for my 94 Chevy suburban transmission range pressure switch. Is this what you are fixing?
@thisisyourtransmission3 жыл бұрын
No, the range pressure switch is a flat switch bolted to the valve body of the transmission.
@ronniebuchanan65752 жыл бұрын
@@thisisyourtransmission I have replaced all my shift solenoids. My 96 K1500 only has low and reverse. I was told the NSS was my problem. What do you think? Let me give you some background I was towing and fluid came out if the vent. When I filled back with fluid I only have low and reverse. I replaced all shift solenoids.
@thisisyourtransmission2 жыл бұрын
@@ronniebuchanan6575 The neutral safety switch is easy to try. If it does not work then you have a bigger problem
@teofistaboxing28384 жыл бұрын
Would a 03 denali not engaging in any gear be this sensor ?
@thisisyourtransmission4 жыл бұрын
No, a broken pump can do this
@7curiogeo4 жыл бұрын
Why not shim the 2 flats to fit tight to flats in plastic ring? Super glue?
@thisisyourtransmission4 жыл бұрын
That is another way. What would you use as shims?
@malcommooney80863 жыл бұрын
dont argue with a proffessional
@cedricalexander92744 жыл бұрын
Ok u showing how to stop it from moving but what the little line on the side mean do it mean it has to b lined with that line.
@thisisyourtransmission4 жыл бұрын
The lines show that the range sensor is in the neutral position.
@cedricalexander92744 жыл бұрын
@@thisisyourtransmission ok so it will not b lined once it's in park rite.
@thisisyourtransmission4 жыл бұрын
@@cedricalexander9274 no.
@cedricalexander92744 жыл бұрын
Ok just making sure because it still wont start so I just made a push start to get it to the shop.
@shadowoutlaw98344 жыл бұрын
@@cedricalexander9274 check your nautral safety switch on the stearing colume under your dash board its what your shift selector is connected to a box with a wire harness plugged in to it .. replace that or put your shift selector into nautral postion and try starting it that way if it starts that way and not in park to start then it deffinitly is your nautral safty switch on the colume .
@brianklein63875 жыл бұрын
Hopefully you don't push that super glue back into the shaft oil seal or that would be a messy leak when the shaft gets glued to the oil seal & tears that seal
@Cmaloneify5 жыл бұрын
Brian Klein y?
@teofistaboxing28384 жыл бұрын
My Yukon Denali act as if it has no R 1 2 3 D. Runs smooth but when you shift nothing engages. Could this sensor be causing that issue?
@thisisyourtransmission4 жыл бұрын
I don't understand this question.
@reAllyNoWayyy4 жыл бұрын
I have the same issue 😬
@dboi50483 жыл бұрын
Mine to I have a 2002 tans am won't shift to any gears ...I was driving doing 55 and just went out help plz
@GhostGats Жыл бұрын
Did you ever figure out the issue I’m have the same issue currently
@hustlingforjesus5 жыл бұрын
How do change range sensor in 2007 equinox
@RickPreciado5 жыл бұрын
I have a 460le transmission aswell i have a gm code 28 transmission range sensor switch error but it doesnt look like this one on this video. Could it be inside the transmission? Everytime i go from park to drive my truck jolts hard or from drive to park.
@thisisyourtransmission5 жыл бұрын
What year is your vehicle?
@SamuelSilva-go8ix5 жыл бұрын
THIS IS YOUR TRANSMISSION 93 Silverado 5.7 2wd i have the SAME problem & have my 3/2 solenoid coming in the morning. HELP 5754496811 silvasamuel0515@gmail.com
@koshnaranek23174 жыл бұрын
Is your transmission manual the switch is much smaller and screws into the transmission in the passengers side.
@charlesjimenez6675 Жыл бұрын
So would this be Part of the mechanics Job to set it RIght when he has Rebuilt your Transmission, because I've been having issues since day one, and it's been going on 4 months with this Rebuilt .. He said he's been working on Transmission for 30yrs " Really " so why have I've been having to take it back 3 times for something else that you have to buy and replace . This last time he told me that I needed to but a new Neutral Safety Switch, but I noticed that my reverse lights weren't coming on . It has a 1 yr Warranty, but he will Not give me ANY RECEIPTS on any of the Parts for the Rebuild .. WTF 😤😡
@charlesjimenez6675 Жыл бұрын
I forgot to mention the reason I took it back in the 3rd time is because the 2nd time I took it in I didn't drive it on the HWY, but when I did it didn't want to change into Overdrive, when I took it back the 3rd time he said that it was working correctly . I had taken my Suburban to Amco Transmission to confirm that it wasn't shifting to Overdrive and they Agreed with me, but the Mechanic said it was working correctly. But I don't think so, so now it sits till I can come up with Another $3.000 to get it fixed RIGHT, WHAT A B---- !!
@thisisyourtransmission Жыл бұрын
The shop does not have to give any recipes for part. This is proprietary information. He does have to honor his warranty. Some places included a new neutral safety switch with a rebuild and some do not.
@cadillacslimm545511 ай бұрын
Bolt size?
@michaelbell82494 жыл бұрын
Hey is that metal piece that popped off necessary?
@thisisyourtransmission4 жыл бұрын
The metal piece is only there to line the sensor up to the neutral position. Once it is lined up and installed, it needs to come off.
@backwoods76782 жыл бұрын
Ok if you forget to put in neutral and take that part of is this bad
@waltercardenas73544 жыл бұрын
Also when I drive 1s to 2nd and 3rd are fine ones I get to 4th gear it hit hard. Any help would save me some money I just lost my job. Money is tied. Thanks
@jeremyhanna38524 жыл бұрын
That trans will died soon it's the 3 to 4 clutch pack that's how 90% of 4l60 die
@AzTkSaiyan3 жыл бұрын
I was having the same problem but now i can only go up to 30 mph its like i only have 2 gears
@mikeb32635 жыл бұрын
Been messing with one for a few days now. After buying two of them they both have random readings. I was just coming to the conclusion that thing is slipping on the shaft.
@michaelbaskinmichael98623 жыл бұрын
4l60e turns no matter what gear it’s in what’s wrong
@thisisyourtransmission3 жыл бұрын
I do not understand the question.
@michaelbaskinmichael98623 жыл бұрын
The torque converter is in a bind from not putting it in all the way , which I did not install but after I fixed the transmission I put it in making sure it was good thanks for your help
@hockeyplayer8372 Жыл бұрын
Metal jb weld
@thisisyourtransmission Жыл бұрын
It would also work
@ivaneberle3972 Жыл бұрын
If your transmission repair chops are anything like your camera work-- just flat no
@thisisyourtransmission Жыл бұрын
My camera work is bad at times.
@frankh54995 жыл бұрын
Your guide clip is still on
@keepitthoro67683 жыл бұрын
Could this make code P0700 come up?
@thisisyourtransmission3 жыл бұрын
p0700 is a generic code, you need a scanner to see the other specific code that has been stored.
@keepitthoro67683 жыл бұрын
@@thisisyourtransmission no other code....wait there is a p2534 ignition issue 🤷♂️
@keepitthoro67683 жыл бұрын
@@thisisyourtransmission nothing else for codes OR transmission codes stored....
@garymoore24875 жыл бұрын
I was driving my truck along my other three Avalanche and notice I didn't have second and third 34th I'm sorry 34th now we started removing transmission when I realized that the bottom plug was not in the neutral safety switch would that be a reason I didn't have 3rd and 4th
@thisisyourtransmission5 жыл бұрын
To be honest, I do not know. Now, I would need a wire diagram to see what the bottom part of the switch is for. How many miles is on the transmission and did you remove the transmission pan first?
@charlesbanks6394 жыл бұрын
Will adjusting this switch make my reverse lights work on my 1997 chevy? I put it in reverse and they will not come on
@thisisyourtransmission4 жыл бұрын
Are you referring to the back up lights in the back of the vehicle?
@charlesbanks6394 жыл бұрын
@@thisisyourtransmission yes
@thisisyourtransmission4 жыл бұрын
@@charlesbanks639 I can't tell you that adjusting the switch will work. Testing is needed on the circuit that goes to the back lights.
@keepthelikesat7104 жыл бұрын
Wats the actually word for that shaft that the sensor goes onto. My transmission leaks from there. And not sure Wat it's called to find out if it has o rings on it or wat
@thisisyourtransmission4 жыл бұрын
Manual shaft
@dustytoney76964 ай бұрын
Fix your mic! Couldn't stand to even continue from the scrappy rustling that's annoying AF!
@nickbean45 жыл бұрын
Hey I have this issue with mine. Is there anyway to buy the shaft and replace it. If so what's it called?
@thisisyourtransmission5 жыл бұрын
Why do you want to replace the shaft?
@thisisyourtransmission5 жыл бұрын
It is cause the manual shaft
@nickbean45 жыл бұрын
@@thisisyourtransmission yeah my shaft is bad I just got the part today. It was alot of play in the shaft its self.
@carlosserrani57692 жыл бұрын
I broke that shaft of a f150 89 Can it be replaced?where do i get the part?
@allantanchak11654 жыл бұрын
No volume
@jonesvaughn Жыл бұрын
That's typical shade tree mechanic, super glue, really, replace the shaft
@elnacho2146 жыл бұрын
My 03 tahoe wont shift into 1st or 4th gear. I replaced both shift shift solenoids already. Can the trans range sensor be the problem?
@thisisyourtransmission6 жыл бұрын
elnacho214 if it is showing the correct readings, then no the range sensor is not the problem.