600HP Twin Turbo Ecoboost F-150

[@jkcollectors2529]

the bottom truck on the list

[@molonlabe287]

600hp. Lmfao. That gen 1 truck is going to need huge turbos, e85 and a shot nitrous to make that. I needed a good laugh today

[@yourlocalcertifiedidiot5010]

My 14 eco has Cold air intake Intercooler Tb spacer Aftermarket turbos i went 5mm bigger Cam phaser lockouts Forged rods and pistons Bored 5 over 93octane race tune It makes 27lbs of boost maxed out Its sitting at 495 to the wheels and 502 lb I blew the motor up thats why i have the rods and pistons i figured id go bigger when rebuilding it

[@jimmydiamond75]

What exactly blew the motor?

[@joeyjohnson7998]

I like how everyone calls an ecoboost a lawnmower but they make better power and better economy

[@russianbot5554]

Joey Johnson facts

[@brycemcelwee7281]

I agree but if it weren’t for the turbos it wouldn’t make that much power

[@russianbot5554]

Bryce Mcelwee Thanks captain obvious lol

[@xxrounds64]

@@russianbot5554 he's not a "do more with less" kinda guy haha

[@therealhaywoodjablomi]

@@brycemcelwee7281 if you didn't have legs you couldn't walk.

[@redsand848evo]

For reference, my '13 eco literally had every available mod available including the turbos, I made 486hp/568tq when I dyno'd it in Denver a few years ago.

[@TTorres1183]

Nice man!

[@DatS1ck_LML]

Elevation is a huge factor

[@jimmydiamond75]

I know this is old but I’m doing the same to my 2012 with Garrett Powermax, BD manifolds, catless 3” into 4” MBRP, hot/cold charge pipes, Atlas intercooler, Melling HP oil pump, AFE Stage 2 intake, 170° stat, BCB custom data log tune,etc etc. I’ve been told that all I can expect is about 500-550hp total. Did you do anything to your fuel system, i.e. HPFP bigger injectors, meth, anything else? Or did you have all that that I’m doing and still got 468? Thanks for the reply if you get this!

[@redsand848evo]

@@jimmydiamond75 I had turbos, CAC, AFE intake, 170 stat, DP, 3" exhaust, throttle body, bigger lift pump and meth. At the time there weren't any additional fueling goodies unfortunately. I probably could have made more after I sent Mike my Dyno sheet, he updated my tune.

[@egcivic9390]

Yea these are inflated numbers on the video. Your only cracking over 500hp if you have bigger turbos and fuel system.

[@Everfall6t9]

Not measuring 1:1 gear ratio. Can hear the truck shift down. Numbers are not accurate. Try running it in manual mode not auto. Dynos only measure torque and calculate horsepower. Shift down, torque goes up and HP is calculated higher.

[@TTorres1183]

+Everfall6t9 ok thanks.

[@joejoe5884]

where's the proof ?? data sheet ? I would try another dyno... dyno on wheels are sketchy..

[@maxtredway4932]

That truck has almost 400 horsepower stock. I’m sure all those upgrades makes a difference

[@roymooner1]

@R R 365 stock at the crank 15% drive train loss youre around 330 hp

[@BobbyKuul76]

There is a reason that this video didn’t have the dyno chart posted.

[@55Berg]

It makes 365hp stock. Adding the mods you listed would get you a little over 400hp max. That would not spike your HP and torque up that much with such little mods

[@Yung_Hefty]

He’s probably missing the fuel upgrade. Because with said mods they can make a little over 500 to the wheel easily. They’re well know for that, but 606? Nah he has to be on E85 or bored turbos.

[@chrisbaker944]

Anyone know the exhaust setup??

[@JoseMorales-ep7id]

Whats done to the truck?

[@CharlieIIpics]

Every pull had a shift spike in it. Look at the graph around the shift spike and you'll see the true power. Don't these trucks have a manual mode? Obviously we don't get to see the graph....

[@BoostedVdub]

Is the motor built or is it stock?

[@Oilfieldmuscle]

I'm gonna make a video with my daughters power wheel and show it on the dyno and never show the chart and expect you to believe it's going for the 405 list.

[@TTorres1183]

DO IT PLEASE!

[@SantanKGhey1234]

That actually looked like 1606hp to the wheels, better double check that dyno plot...

[@5.0_lewy6]

This does not make 600 at all...something was reading wrong. Mine is like 400ish with same mods and MPT tune

[@russwilkerson2741]

Wow real interesting watching the wheels turn. I want see numbers off the dyno. Don’t believe it for a moment

[@jimmydiamond75]

Same

[@nathanielquick4259]

i know this was posted a while ago but what was the setup if you remember

[@ethan5.4s89]

I have a red f150 2011 platinum twin turbo and i made 410 but there is no way he made 600 hp unless he is high

[@scottmcleod7129]

DYNO SHEET?

[@timmyeckert8340]

Did y’all do any internal upgrades or anything like that? Cause I have MBRP careless downpipe, 3inch catback side exit exhaust, cold air intake, and SCT X4. Could my truck make the same power on stock internals? 2011 f-150 3.5 ecoboost

[@jimmydiamond75]

No

[@garrettrush8243]

Haha and my lawnmower has an LS, cuts the lawn in 10 seconds or less.

[@TTorres1183]

+Garrett Rush lol bring it by and let's put it to the test :D

[@russianbot5554]

Meanazhell now eco-boost lawn tractor that’s impressive 😂

[@dago633]

where is the dyno chart?

[@russianbot5554]

Dago castillo in his dreams lol

[@1danrdz]

I don’t believe it. Basically it’s stock

[@TFD1982]

Didn't sound like the trans had enough to time to get to the next gear

[@TTorres1183]

+TFD ! What part of the vid are you referring 2?

[@Venis-Pagina]

TTorres1183 3:03

[@jaronhasley9248]

Brother I wish your truck made that much because that would mean mine would make 700hp. When you dyno your truck if it has 3.55 gears you should run it from 2K-6K in 3rd gear manual. When the dyno operator hammered it, it down shifted to 2nd...heck maybe 1st. Definitely gave you some hp and tq spikes, but they aren’t true rwhp and tq numbers. Like I said though....I wish because mine would have more then yours! Lol

[@TTorres1183]

That is truuuu

[@SuperMudbog]

I walked by this one at the meet when it was on the dyno actually

[@TTorres1183]

+Ryder Smith it’s a fast truck man!

[@coltonragain8938]

LOL. "If you know these trucks as well as i do". As you say an ecoboost gains 220 hp from tune exhaust and intake.

[@TTorres1183]

+Colton Ragain maybe something was messed up with the dyno...

[@tristanandshayschannel8428]

Lol I was thinking the same thing. Maybe picked up 60hp over stock

[@lopinslow17]

LMAO. That dyno must have been wayyyyy off. You're making maybe 400 RWHP...

[@TTorres1183]

+BlakeBurkett lol I disagree... on the low end on one of the pulls it made like 520hp

[@lopinslow17]

You can disagree all you want; doesn't make you right. Do some research. This truck would be making 200 more horsepower than ANY EcoBoost with basic bolt ons has ever made. There have been hundreds of those combos dyno'd. Don't be stupid. I was at the meet, with 3 EcoBoosts. Didn't I see this truck running on the track? Pretty sure it was running 16s...

[@TTorres1183]

+BlakeBurkett indeed you did see this truck on the track. Don't be stupid this truck ran 14's.

[@lopinslow17]

T Torres1183 dude. That's nowhere near 600 HP. Do some research... use a 1/4 mile calculator. This truck would be running 11s if it were 600 HP.

[@TTorres1183]

+T Torres1183 you can disagree all you want man. I'm just going off facts from the dyno and 1/4 times...

[@angelpabellon]

can you please list the mods??

[@offroadpatriot7219]

LMAO 600 hp and 880 Torque. Actually made me laugh. Maybe and I mean maybe mid 400's 450 ish is possible. Much more than that I'm calling bullshit.

[@lostxcracker6545]

It has everything done to it but a intercooler I think it has a cold air intake and a cold air intake a BOV oh did I say cold air intake makes 900hp we are really pleased with that cold air intake

[@m.m14433]

I absolutely love these EcoBoost trucks. I have the '13 fx4 f150 EcoBoost. Sadly my heat shield on my exhaust rattling like crazy. No time to fix the damn thing.

[@austinmccoy9435]

It’s most likely your waist gates

[@m.m14433]

@@austinmccoy9435 no it was the heat shield.

[@paulwilliams821]

no way that's any where close too 600 I think MPT performance would know anyone who owns a ecoboost f150 knows who MPT. That stock motor would be in chunks before it gets close to 600

[@jimmydiamond75]

Unless he spent $15k on a closed deck block and forged internals 😂 Which he clearly didn’t

[@stevew6910]

2nd gen 3.5 2017s have a different inter cooler on them. Should never have to drain it

[@TTorres1183]

+Steve W that's good to know. I didn't know that.

[@Ryan-ex4wr]

hell yeah man great build

[@TTorres1183]

+Ryan thanks it’s a friends

[@bamaspeed3318]

does this truck say ecobeast on it? i think i seen it at the ymca in wetumpka??

[@TTorres1183]

+Bama Speed no sir, it just has a twin-turbo ecoboost badge. Thanks for watching and please subscribe:D

[@KnightsGarage]

What all mods have y'all done?

[@KnightsGarage]

Sorry. Posted that before I watched the end of the video.

[@TTorres1183]

+Randy Knight no worries thanks for watching! Please hit that subscribe button!

[@RobertsAutomotive]

Added a 0 at the end of the max horsepower #'s

[@blackthunder7342]

It wasnt in a 1 to 1 gear he was probibly in 3rd or 4th im not sure what gear is 1 to 1 ratio on this truck. Thats also why your torque was so much higher than your hp. When from the factory they were pretty cIose. I work at a dyno/speed shop for a living and i see this all the time when deternming the 1/1 gear real hp numbers are probibly 480 to 500hp and about that in torque

[@CharlieIIpics]

This looked like a Dynojet, those don't measure torque and then back-calculate power based on gear ratios to estimate engine rpm, they directly measure power by measuring how long it took the vehicle to accelerate a roller of known mass to a given speed. Vehicle gear selected does not change the accuracy of the power it produced. What happened here was clearly a shift spike. If that was Dunbar's dyno, I am fully confident that he told them that. No doubt the graph has a huge shift spike and the dude is using those values on the spike.

[@jacobstuntebeck-lokken6927]

UHHHHHHHUHUHU THE REV LIMITER 🤤🤤🤤

[@Walker_328]

You my friend are goofy to say the least..Glad you are proud of this truck though. Still a nice truck.

[@TTorres1183]

Thanks for watching Bryan

[@m.m14433]

Bryan Miller what does him being goofy have to do with anything? You're dopey. See how irrelevant that comment is?

[@patrickpierre6114]

hold on... no Intercooler or Turbo upgrade??? ok.

[@2assholesinacarandoccasion393]

what exaust does he have

[@TTorres1183]

MBRP

[@55Berg]

Why didn't he just put it in manual mode for a full pull

[@Travis-hl3oz]

I don't know about that y'all didn't run into it any ignition or running out of fuel problems I didn't think stock coils or fuel pressure would get you numbers that high

[@NoblestoftheLIONs]

No way with an XLT he's making that power. At least an FX2 or higher us needed!

[@NoblestoftheLIONs]

@R R joke, just like the clip... Lol

[@trentc32]

Montgomery Motorsports Park?

[@TTorres1183]

+trentc32 thatbis correct!

[@JohnVHRC]

What exhaust is on that?

[@TTorres1183]

+JohnVHRC MBRP

[@JohnVHRC]

T Torres1183 I like it.

[@TTorres1183]

+JohnVHRC do you have a ecoboost f-150

[@JohnVHRC]

T Torres1183 yessir. 13 fx4 all stock

[@TTorres1183]

+JohnVHRC nice man!

[@jamieenglish254]

Sorry but you are way off, that truck is no where close to 600 rwhp. Doesn't matter if you say it, the truth is that truck but down 400 whp at best and you know that, that's why there is no dyno graph pic.

[@bakeward8802]

Exactly lol why would you not show it in real time if you had the world most power full eco. Shit I showed real time numbers with only making 300rwhp on my 3v even tho that was embarrassing considering what I have done lol but we had problems with fuel and my tuner jumped out the truck saying it so I got both on video . This guy just straight up lies to get views.

[@TheLilbilly392]

Portable Dyno accuracy? Ha, good money maker tho

[@kenrobinson1099]

Real trucks have HEMIs!!!

[@ramren16]

Dont think I would trust those baby straps holding any vehicle on that dyno

[@twizz420]

The ecoboost F150 is twin turbo from the factory... clickbait title

[@TTorres1183]

+Nikolas Tesla who doesn't love a good click bait title :D. Thanks for watching!

[@bears041068]

I definately do not see a 600hp truck here.

[@bears041068]

I have a 2017 with no mods, I'm not impressed with the said 600 hp performance.

[@weightlifter75]

No way that's 600 not even for a second.i have more mods and no way it feels like my buddies 500hp Mazda. I have installed High voltage grantelli ignition Coils New motorcraft spark plugs gapped to 28 BBk 73mm throttle body AFE charge pipe Heartthrob 4in cat back K&N drop in filter SCT 93 canned tune I'm running 22 psi of boost so no chance at all I'm bitting on this one

[@Jay-me7gw]

May wanna get that dyno checked. A stock turbo first gen 3.5 Ecoboost can't make 600 crank nevermind 600 wheel. Sorry.

[@Tyler.Johnson19]

Own up and tell the truth. Don't be a fake.

[@nathant2414]

You ain’t making those numbers with just those mods especially on a first gen 3.5.... stock intercooler..? Lmao!!!!

[@natetoland7537]

It's possible, I've seen a 3.5 with stock turbos hit 700hp to the wheels with an upgraded intercooler, fuel system and exhaust, just because you can't accept a v6 being more powerful than your 15 year old v8 doesn't make the results false

[@molsonice2473]

not even close to 600 hp, or 800 pft..

[@Sinister_Reaper]

doesn't make 600hp sorry bro lmao, but hit up mpt performance, I got my tunes and plugs from them, bought my nitrous before I heard about them but if youre looking to make big power they the ones to call

[@TTorres1183]

Thanks for the info!

[@russianbot5554]

I’m thinkin more like 506hp.....I’ve got a fully built 2019 and it’s makin 500hp and 600tq

[@gunnernichols1389]

Did you build it yourself or professionally?

[@russianbot5554]

gunner nichols SOB performance built in GA

[@russianbot5554]

gunner nichols I started with ordering everything from stage three motorsports that they carried lol

[@-Fecoboost]

What's the best hand held tune for 3.5?

[@egcivic9390]

HP tuners if your trying to get dyno tuned by someone In your area.

[@xX_M1K3_Xx]

Wow so many haters in the comments!!

[@TTorres1183]

+xXTheJokerXx so many haters...

[@bakeward8802]

Well they shouldn't spit out straight up lies lol

[@dieseldemon8562]

880 lb ft of torque 😂😂😂. Out of 214 cubic inches???? Hmmm.

[@scottchong3202]

Truck is more than capable of 600 wheel hp but with those mods not even close my 15 tuarus sho has way more mods and not hitting that number

[@mattrugg8462]

Go on a dynojet and repost you wont

[@jerrodcorey25]

LOLOLOL BULLSHIT. Dreaming!!!! Dyno way off buddy. I got full 3 inch, ported manifolds and turbo adapters, full race twin turbo upgrade, Wagner Evo Intercooler, pro meth injection system, and the best tuner on earth SSi, and kill shot tune. Still under 500 rwhp. Without upgrading fuel system and adding nitro, your not 600 hp

[@drowzynate722]

Lmao yea that was the fastest dyno pull I've ever seen. This truck does NOT make that much power. If you think it does I'd gladly run you with my 349hp/445tq Tremor just to beat your "600hp" truck.

[@MegaElkHunter1]

Your tremor makes less power my 2017 ecoboost does stock... quit talking shit 😂😂

[@drowzynate722]

MegaElkHunter1 what does that have to do with this truck jackass?? Of course your 2017 makes more power it has different turbos and fuel system. Don't get upset cuz I'm saying this 11-14 style is NOT making 600hp. It's like comparing a 2015 5.0 engine to a 2011 5.0, whatever point you're trying to make is idiotic.

[@MegaElkHunter1]

Nathen Lorenz because his truck has the exact same motor as yours and it's on the same steel body because they didn't make the tremor on a 15+ but his has mods and from the numbers you just said you're still running stock as fuck bud (actually the numbers you said specs have you put lower than factory numbers so I don't know how you fucked that one up) lmao. And while his may not be 600 hp or even close his has some mods and a pipe with an intake and a tune on these trucks goes a long way. (And BTW the gen 2 ecoboost is a whole lot more than new turbos and a fuel system bud lmao) whole fuckin engine was redone. Quit talking shit unless you know facts.

[@MegaElkHunter1]

Nathen Lorenz I'm just putting you in your place because you think your stock ass tremor is a racetruck when from what you originally posted you're making less power than what they were rated for from the factory lol

[@drowzynate722]

MegaElkHunter1 lol but mine is tuned. Difference is that my numbers came from a mustang dyno not a free flowing junk dyno and that was before my intercooler And on only 18psi not 20psi like most other tuned truck and I still have ran 13.5@102 spinning with a 2.1 60ft. So once again you're an idiot. It's called wheel hp. Fords numbers are crank hp. Yes if I ran 20+psi (and a bit more timing with an e30 mix, incase you say 2psi won't add 50hp/50tq)like others I'd be around 400hp/500tq. So I'm like 50hp/50tq short. I know the Tremor didn't come in the 15+ aluminum body. It only came in '14. That's irrelevant to this topic. And for you to say my facts are wrong because I didn't list every new item that's new on the gen 2 3.5 just shows even more how you're an idiot. I wasn't wrong about what I typed, I just wasn't going to list every item but here you go. Ford calls this EcoBoost “all new,” and indeed it carries over only the old engine’s bore center dimension, piston displacement, and cylinder liners. The block is new, the turbos are new, the cooling system (which features new flow paths and a higher-volume, higher-rate water pump) is new, and the fuel-delivery system now employs both direct and port injectors for improved emissions and more power. Would you like for me to log into my fmc dealer account (ford dealership login) and type out the bore specs and torque spec of everything as well?? I'm sure you'll wanna add how the head torqued changed or something stupid like that now too. The point to all of this is saying this guy shouldn't be hyping things up, saying that this truck makes 600hp. If that's the case I'd like to race him in my "350/450" (approx numbers) just to claim that I've beaten a 600hp truck.

[@blakejames7384]

They sound stupid though

[@popwarhomie]

Bullshit.

[@jragz_1759]

🤣🤣🤣🤣🤣🤣🤣

[@turbodreamscometrue2818]

Bull Crap!