Thanks zach I really appreciate the quick response bud..great videos nice to see some in-depth videos with someone who actually explains thoroughly how to do things..awesome bud ..keep up the great work
@divino360big6 жыл бұрын
I really enjoyed your work. Congratulations!
@edzgarage6 жыл бұрын
Thanks for the comment and for watching!
@canadianboy4926 жыл бұрын
Nice work. A man that actually does it right with some speed
@edzgarage6 жыл бұрын
Thanks for the comment!
@alittlebitofeverything50902 жыл бұрын
Very thorough thank you. I have a 14 Ram 2500 with the Cummins and 68RFE. Since it was brand new it has always clunked in the driveline at low speed when letting off the throttle or getting back on it. If I do a transmission relearn on it, it goes away, but only for about 100 miles then it comes back. Any thoughts?
@frankdelvecchio84756 жыл бұрын
Good man.... I greatly appreciate that..I was second guessing it..not now thanks..I have 2 175 hp ppumps anything I can do for preventive maintenance..besides delivery valves or springs.. it's an automatic so should I do Springs or delivery valves 3k or 4k..delivery valves?if so what size... maybe some heavy towing definitely a daily driver.. and is there anything with the 175 pumps that might have some troubles I hear something about plungers sticking.. I know it's a lot of questions..sorry thanks ..just really looking for reliability more than anything
@jessename78496 жыл бұрын
What would I need to put a 68RFE behind a 4 cylinder Cummins? Also what transfer cases could I use behind it? Is a way to manually lock up the torque converter on a 68RFE like can be done on the 47-48 s (what gears would it work in if so?) Does the 68RFE circulate the fluid in park & warm up better in subzero cold than a 47-48 trans?
@RBLUS_TY3 жыл бұрын
68RFE on a 5.9L? Pretty helpful, I will say. I'm trying to put together an ethanol inline 6 based entirely on the Cummins 5.9L block and wanted to add a built 68RFE to it. But I always wondered if the 68 would fit the 5.9L so like I said your video pretty much says it's possible.
@ShnitzlHaus6 жыл бұрын
went together with ease!
@edzgarage6 жыл бұрын
Yes, we were thinking the same thing... "We sure are getting good at transmissions... sucks that we're getting so much practice" lol Thanks for the comment and for watching!
@zx8401ztv6 жыл бұрын
Smashing re-install, i hope it behaves itself :-D. The multistage extention made me smile, was it not possible to use a solid bar then?
@edzgarage6 жыл бұрын
Turns out the problem is cured! Not sure if it was the pump or the filter so we're going with... YES it was both lol The stacked wrench extension was used because he couldn't get a socket on the bolt and I don't have 2 foot boxed end wrenches lol
@frankdelvecchio84756 жыл бұрын
And it's absolutely okay to run 24-valve stock injectors to get re popped for the P pump swap
@djverhulst6 жыл бұрын
well done, a question, why don't you take care of all rusty parts of the chassis ? it was easy to derust them and protect them againt rust ?
@edzgarage6 жыл бұрын
Here in the midwest US rust is a way of life lol We were commenting on how little rust the truck has for it's age lol Thanks for watching and for the comment!
@jessename78496 жыл бұрын
Laziness or unwilling to go the extra mile. I live in the Midwest so I know all about the over use of salt on roads extra too.
@edzgarage6 жыл бұрын
Interesting comment... you call us lazy or "unwilling to go the extra mile" and then post questions that can be answered in a web search... lazy or unwilling to go the extra mile? We are, by far, not lazy or unwilling to go the extra mile. As you know, being in the midwest, it's too cold and wet to do body work on a daily driver we just purchased. It's all good - thanks for watching!
@frankdelvecchio84756 жыл бұрын
Great videos guys...this question is alittle late..about the p-pump swap..did u guys have a set of injectors sent out to have pop off pressure set..I hear of some using stock 24v injectors working...what are your guys thoughts on this ..I just installed a set of brand new 75 HP bosch injectors in my 24v ..and wondering if u guys think they would be ok..thanks in advance
@ZachU8126 жыл бұрын
Frank Delvecchio Hi Frank, I’m currently using a set of injectors set to 24v pop pressure with no issues. In my opinion there’s no reason to change it. The pop pressure effectively delays the injection event by a small amount and you can compensate for that by setting the injection timing a little bit higher.
@jessename78496 жыл бұрын
Get them repoped to 180 bar the p-pump spec (140 bar is 24v spec I believe.) You'll get a better injection that way. Which will give you a more complete combustion, more power, & better economy. People try to over compensate poor equipment with timing (Marine injectors for example) but injecting fuel out side of the piston bowl causes poor combustion efficiency, access combustion Heat without optimum pressure to motion transfer, and in extra cases can cause a piston top to be melted
@frankdelvecchio84756 жыл бұрын
Jesse Name ..thanks bud I appreciat it...can I get 24v stock injector re popped for a ppump swap or do they need to be a higher hp injector..thanks in advance
@ZachU8126 жыл бұрын
Frank Delvecchio I would not waste the time and money getting your injectors re-popped. It has absolutely nothing to do with spraying fuel inside the bowl or melting pistons, I suggest reading up on the topic a little more. If you do decide to get it changed, the pop off pressure is nowhere near what Jesse mentioned. I’m still running my 6x.013s at VP pop pressure with a ppump and making well over 600hp with no issues at all.
@markvietti4 жыл бұрын
68RFE should never have been used on the diesel.
@karljacobson15756 жыл бұрын
I asked you about a 640 Ford tractor a few weeks ago. I took hood and fuel tank off and valve cover. Looks like it's full of water!! I have a picture but not sure how to send, but it's crusty!! Ruined? Can I get used parts I wonder? Let me know your thoughts when u get time!!!
@edzgarage6 жыл бұрын
PM pics to me on my Facebook page if you can facebook.com/EdzGarage/
@karljacobson15756 жыл бұрын
EdzGarage could I e mail you? Don't do Facebook!! My e mail is Sodbusterk@yahoo.com if you don't mind!!!
@karljacobson15756 жыл бұрын
EdzGarage I took the head to a local machine shop and said they could fix it!! So we will see how that plays out......
@frankdelvecchio84756 жыл бұрын
Hey bud sorry scratch that last question I'm just going to run my 75 horse injectors I just got they should be okay right that's what I meant to say
@ZachU8126 жыл бұрын
Frank Delvecchio Hey I just saw this, you’ll be perfectly fine with those injectors. I wouldn’t second guess running them, good luck with the swap!
@jasonmushersee6 жыл бұрын
is'nt it always hard to get those transfer cases up there. just no where to put a jack safely
@edzgarage6 жыл бұрын
Yeah Bud, and they're heavy too. We need a better trans jack. Thanks for the comment!