Stave construction is a great way to make cylinders without needing to buy large dimension wood. This is a simple method very easily accomplished. Want to support my channel? www.buymeacoff.ee/GordRock
Пікірлер: 106
@glencrandall70513 жыл бұрын
This old video just popped up. I cannot believe I haven't seen it yet. Typical Gord rock work. Well produced and very informative. Glad I saw it.
@GordonRock13 жыл бұрын
Wow, that is an old one, Glen. I believe that was the second video I did. I’m glad you liked it. Thanks for watching, Glen! You are much appreciated, my friend. Stay safe and healthy!!
@federicoolmedo27883 жыл бұрын
Good video, greetings from argentinian!
@GordonRock13 жыл бұрын
Glad you liked it. Thanks for watching! Greetings from Canada! 👍👍🇨🇦🇨🇦🇨🇦
@judithfairchild86202 жыл бұрын
Thank-you for showing us how to do it easily and right
@GordonRock12 жыл бұрын
My pleasure, Judith. I hope it helps you. Thanks for watching!
@davidclauson52568 жыл бұрын
Don't know how I missed this video, but glad I was going through and watched it. As always I learned something from you, thanks, I'll definitely give this a try.
@GordonRock18 жыл бұрын
Thank you, David. Thanks for watching. Take care, .....Gord
@kareyber55368 жыл бұрын
/ I also tried *Thebooks2015 .Com* , and this is a great website to learn the basics to advance and specially 16000+ level woodworking woodworking projects and plans //// .....++
@hunterdogztc9 жыл бұрын
Wow, Gordon! Great video and explanation of stave construction. Very well done.
@GordonRock19 жыл бұрын
Thank you, Terry. I'm glad you enjoyed it! Thanks for watching. .....Gord
@billwells80545 жыл бұрын
Excellent, Gord, thank you. My method is similar to yours, but I have been ripping the stave segments along the table saw rip fence. I now recognize the benefit of cutting them on a sled. Bill
@GordonRock15 жыл бұрын
Glad I could help, Bill. Thanks for watching! All the best, .....Gord
@hubbadubchub9 жыл бұрын
Awesome video! I'm planning on building a stave drum and it was helpful to get an idea of what it takes.
@GordonRock19 жыл бұрын
Buster Layne Thank you, Buster. Glad you got some information from it. Thanks for watching; I appreciate the support.
@grantmillard70712 жыл бұрын
Great tips on making stave based constructions. Thanks very much for the information. Cheers!
@GordonRock12 жыл бұрын
Glad you liked it. Thanks for watching!
@hallenw8 жыл бұрын
Excellent Job! The video, pace, instruction and techniques are all excellent. I subscribed for more.
@GordonRock18 жыл бұрын
+Allen W Hello Allen, I'm glad you enjoyed it. Thanks very much for subscribing; I appreciate the support! Take care, .....Gord
@erniezamora95098 жыл бұрын
great video im learning wood and this is helping me alot thanks take care
@GordonRock18 жыл бұрын
+Ernie Zamora I'm happy to be helping, Ernie. Thanks for watching! Take care, .....Gord
@Aprendeartesania9 жыл бұрын
Hellow, good solution for work clamp. Very easy and quick. Bay
@GordonRock19 жыл бұрын
***** I'm glad you liked it. Thanks for watching......Gord
@hawkwind239 жыл бұрын
Hi Gordon , I found your video very informative and as a newcomer to woodturning have learnt from it ,many thanks for sharing All the best Bram
@GordonRock19 жыл бұрын
Bram Sharp Hi Bram. I'm glad you liked the video. Thank you for watching & commenting; I appreciate the support. Have a great day, Bram, .....Gord
@pocketcruisersailing4 жыл бұрын
Brilliant! Thanks a lot...
@GordonRock14 жыл бұрын
You’re very welcome, Paul. Thanks for watching! 😃😃😃🇨🇦🇨🇦🇨🇦🇨🇦 .....Gord
@leighstevens10757 жыл бұрын
I use any idea that means less wasted wood & money. Terrific tip thank you
@GordonRock17 жыл бұрын
+Leigh Stevens Glad you liked it, Leigh! Thanks for watching. .....Gord
@thomasckuzia71295 жыл бұрын
Hi Gord, Very informative video,,, Thanks,,, Tom
@GordonRock15 жыл бұрын
Glad you liked it, Tom. Thanks for watching! Take care, .....Gord
@chandlerdavis9528 жыл бұрын
Very well thought out process and well described. Thank you. I have a different application that this will work nicely with. Its close to what I was doing but yours has a couple extra steps that will make the end result a better product.
@GordonRock18 жыл бұрын
Glad you like it, Chad. Thanks so much for watching & commenting. Take care, .....Gord
@ErikAnderson19 жыл бұрын
Nice video Gordon!
@GordonRock19 жыл бұрын
Erik Anderson Thank you, Erik. I'm glad you enjoyed it!.....Gord
@bearshield71382 жыл бұрын
thank you this is helpful
@GordonRock12 жыл бұрын
You're welcome! I'm happy that I could help. Thanks for watching!
@stringmanipulator10 жыл бұрын
Great method :)
@GordonRock110 жыл бұрын
I'm glad you like it. It's worked very well for me. Thanks for the comment.
@annwahlstrom1492 жыл бұрын
I really learned something new with this video, thanks for sharing great ideas, and I subscribed to be able to watch new and older stuff.🤩❤👍
@GordonRock12 жыл бұрын
I’m glad you liked it, and. I hope you will like some of my other videos as well. Thanks for watching! 😃😃😃👍👍🇨🇦🇨🇦🇨🇦
@danceswithaardvarks32843 жыл бұрын
Nice. Very clear video.
@GordonRock13 жыл бұрын
Glad you think so! Thanks for watching!!!
@norbertkovalovszky29768 жыл бұрын
Good idea Thx
@GordonRock18 жыл бұрын
You're very welcome.
@kosycat18 жыл бұрын
Nice, thank you thank you thank you
@GordonRock18 жыл бұрын
You are very welcome, Jonathan! I'm glad you like it. Take care, .....Gord
@Claudiomarsantos8 жыл бұрын
Muito muito ... MESMO Obrigado útil !!!!
@GordonRock18 жыл бұрын
+claudiomar santos Glad you found it helpful. Thanks for watching and commenting! Take care, .....Gord
@xBeauGaming8 жыл бұрын
I think I will use this to help make a beer mug ;) Nothing like a white oak beer mug...YEAARRRRRR Thanks bud.
@GordonRock18 жыл бұрын
I hope it works well for you. Thank you for watching!
@janicemiller53829 жыл бұрын
Nice job as usual Gord. Inspires me to dust off my lathe
@GordonRock19 жыл бұрын
Scott Miller You let your lathe get DUSTY???? What kind of shop do you work in? LOL!!!
@carlosmarioherrera56556 жыл бұрын
Nice
@GordonRock16 жыл бұрын
+Carlos Mario Herrera Thank you!
@hayyoyoume28 жыл бұрын
cool 😎
@GordonRock18 жыл бұрын
+najib bey Thanks very much. I appreciate that. Take care, .....Gord
@ibilaibila8 жыл бұрын
I have to do this with kit-kat now.
@GordonRock18 жыл бұрын
LOL, it took me a second to get it. Thanks for the laugh. Take care, .....Gord
@billwells80545 жыл бұрын
@@GordonRock1 - Duh! Dumb me, did not get it - thanks for the help! Bil
@annwahlstrom1492 жыл бұрын
LOL
@CarlosAlencarCgalencar7 жыл бұрын
Meu nome é Carlos Augusto e moro em uma pequena cidade no interior do Ceará, Brasil. Parabéns pelo trabalho e pela criatividade, tinha muita vontade de ingressar nesse ramo, mais infelizmente minhas condições financeiras ainda não me possibilitam de adquirir máquinas e assessórios. Fica com Deus.
@GordonRock17 жыл бұрын
Obrigado por assistir, Carlos. Espero que sua situação melhore em breve. Cuidar, ..... Gord
@ffff17588 жыл бұрын
nice video Gord, very clear, but, what if you want to make not a cilinder but a barrel? staves won´t be straight? do you know how to make them? regards
@GordonRock18 жыл бұрын
Sorry, Carlos, it's not something I have ever tried. I'm sure there must be KZbin videos showing how. It just isn't something that interests me. Take care, .....Gord
@JuanGomez-cx1hi8 жыл бұрын
Very helpful video! I have a question...After you make the cylinder, How do you mount it on the lathe? Did you make a chuck for it?
@GordonRock18 жыл бұрын
+Juan Gómez Hi Juan, I'm glad you find the video helpful! If I was to mount it on the lathe I would use a large chuck because it is not too large to do that. If it were a much larger cylinder I would have to make a chuck of some kind for it. If I had enough length to waste some of it I would make sure the end was square and then probably use hot glue to attach it to a glue block. Thanks for watching, Juan. Take care, .....Gord
@annwahlstrom1492 жыл бұрын
One can use a blank and make a tenon on that and glue it on the end, just making sure it's centered before the glue dries!👍 Then just put the tenon in the chuck, and remove the blank afterwards!
@kenharper616 Жыл бұрын
Boy you look young back then. I guess we all do.
@GordonRock1 Жыл бұрын
Well, Ken, if I’m in my late 20s now I must’ve been in my early teens back then! 😂🤣😂🤣 That sure feels like a long time ago, my friend. Thanks for watching!
@roclo99278 жыл бұрын
what if you wanted to make the staves wider in the middle to get a particular effect how can the all be made the same but slightly wider in the middle
@GordonRock18 жыл бұрын
+Roc Lo I'm afraid I don't know as I have never tried that. If you ever figure it out I would sure like to know. .....Gord
@erniezamora95098 жыл бұрын
you dont have videos on how to make barrel staves i want to make barrel tub thanks
@GordonRock18 жыл бұрын
+Ernie Zamora I have never tried barrel staves, Ernie. I'm sure there must be a few videos on KZbin showing the process but I have never looked for them. I hope you find something that helps. .....Gord
@sfcisco858 жыл бұрын
what make wood lathe are you working with?
@GordonRock18 жыл бұрын
Nova DVR XP
@FoxAxel19826 жыл бұрын
would this work on a larger scale? Say 2ft round?
@GordonRock16 жыл бұрын
Absolutely! As long as you have correct angles cut it should work on any size. Thanks for watching! Take care, .....Gord
@thomaskuzia81254 жыл бұрын
Hi Gord, After following the way you made this stave construction I've made a few pencil/pen "cups" that look like wooden buckets,,,,with a steel handle too! This got me thinking about making a wine barrel and after watching just about every video here and looking on the web I'm finding that making a wine barrel isn't all that easy to do and have a lot of respect of Coopers now! I did find one video on how to do the math for stave construction but that math is WAY over my head! LOL Do you have any ideas on how to "easily" calculate barrel staves? Thanks for this and all of your videos! Tom
@GordonRock14 жыл бұрын
Sorry,Tom, I have never even tried to do that. I may have to look for that video and see if I can figure it out. I'm sorry I'm not any help right now! Maybe some day in the future. I hope you figure out before I do. Thanks for following my channel. I really appreciate the support. I would like to see those cups with the steel handles! Did you do a video on them? 😀😀 Happy turning, .....Gord
@thomaskuzia81254 жыл бұрын
@@GordonRock1 Thanks for trying to help me! No videos of any of my work,,, I never knew barrels were such a complicated process, especially the math! Tom
@philipselman256412 сағат бұрын
The math isn’t that hard =. A circle is 360degrees Ok for a 10inch bucket you will have 10 staves which has 2 sides 10x2= 20. 360 divided 20 = 18. the angle on each side is 18
@caballobueno10 жыл бұрын
can i make in a very long lumbers, 2000 mm for exenplo??
@GordonRock110 жыл бұрын
I have never tried anything of that length but can't see any reason not to try. Hope it works for you. Let me know how it goes.
@OramiIT10 жыл бұрын
What is a good way to mount that on a lathe? I don't really have a lot of bells and whistles to mine. Maybe some way to use a jaw or something?
@GordonRock110 жыл бұрын
Ritgar001 It depends on what you want to do with it. I generally put mine in a chuck using either expansion or compression depending on the size of chuck needed and what I have. You could also use a jam chuck if you wanted to. Part of the joy of woodturning for me is the challenge of coming up with a way to hold things on the lathe; there is usually more than one way to do something. Sorry if this isn't a great answer but there are so many variables - size of cylinder you've created, size of chuck(s) you have, etc. Hope this helps!!!
@OramiIT10 жыл бұрын
I just want to do it safely. I had had ceder fly apart on my lathe and smash around. I do know glue is much stronger than wood though so I guess it should be fine. I'll give it a shot.
@GordonRock110 жыл бұрын
Ritgar001 I hope it works out for you. ALWAYS wear a face shield!! I've had things fly apart and if not for my face shield I would have been in the emergency room on at least one occasion. Safety first!!!
@OramiIT10 жыл бұрын
Gordon Rock Yea. I have heard about getting a face shield I just haven't yet I am always out of the direct line of fire though. I haven't been doing much on my lathe recently since I have been doing my first few boxes with miter joints on the table saw. It turned out so-so I should probably lightly sand it and do one more coat of poly, but a few small details are off that I need to fix next time. facebook.com/photo.php?fbid=950585308301786&set=pcb.950585714968412&type=1&theater
@GordonRock110 жыл бұрын
Ritgar001 Thanks for sharing the photo. That's a decent-looking box and every future box will be just a little bit better. If the first one you built was perfect how would you improve? The joy is in the doing, more than in the product; at least that's how I feel about it.
@acheinacacambarecicle65864 жыл бұрын
👍👍👍👍👍👍🏼👏👏👏👏🇧🇷
@GordonRock14 жыл бұрын
Thank you very much! 😃😃😃😃
@jeanmachardy48989 жыл бұрын
Hi Gord. I have used your stave cutting method before but I am now trying to make wooden buckets (coopering). I have a method for cutting one taper/bevel that works to make only one size of bucket but I wish to make different size units and don't want to waste expensive wood experimenting. I was hoping you had a method for stave cutting to vary all the possible sizing (top/bottom diameters) possible. Thanks for your consideration. Alan
@GordonRock19 жыл бұрын
Jean MacHardy Hi Alan. I'm sorry but I've never tried making anything but straight cylinders with staves. I would assume someone out there has a chart for this but I don't know where to look for it. I hope you can find it. Sorry Alan, .....Gord
@GordonRock19 жыл бұрын
Jean MacHardy Alan, I did a quick google search and this might just help: forums.finewoodworking.com/fine-woodworking-knots/general-discussion/formula-tapered-staves Hope it helps!! .....Gord
@jeanmachardy48989 жыл бұрын
Gord Rock Thankyou Gord. Alan
@lolojr19 жыл бұрын
great video for a robot
@GordonRock19 жыл бұрын
Bill Lolo Thanks for the feedback. Hope you enjoyed it!
@lolojr19 жыл бұрын
Autually I really did even subscribed !
@GordonRock19 жыл бұрын
Bill Lolo Thank you, Bill. I appreciate the support.
@cherylshire12254 жыл бұрын
Kitkat
@GordonRock14 жыл бұрын
Caramilk 😂😂😂😂 ???
@avagage18 жыл бұрын
please turn off the music
@GordonRock18 жыл бұрын
That video was one of my very first. At the time I did not know how to use the video editing program and couldn't add more than one track. I've improved since then and I hope you will enjoy my more recent videos. There is no way to alter the old ones. I'm sorry you didn't like it. Take care, .....Gord