CityBug Key Case Replacement, Citroen C1, Toyota Aygo, Peugeot 107

[@lovedmygti]

life saver. swapped the fob over on me mums car, but didnt realise the transponder chip was seperate to the main module. nearly chucked the old unit away. car wouldn't start this morning and found your video - thanks so much!!

[@aaanton11]

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

[@vBDKv]

Same here haha, I never even realized a tiny chip was in there.

[@WalidFeghali]

Seriously man, you created this video just as I was going to turn this key into the car dealership for repair (I think 80 quid?). You are a lifesaver. Also, I managed to fix my engine misfire + engine light troubles with one of your coil switch tip videos. Thanks 100 times over! Best, W.

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@SuperNeplusultra]

I have watched a dozen videos trying to get my new car key to work. You are the only person to mention the transponder which was still Sat in my old key casing. Thank you so much!

[@aaanton11]

Glad I could help Thanks for the great comments👍🏻👍🏻🛠

[@vBDKv]

I got 2 microbuttons with mine and a screw. I gotta say, the buttons are 10000 times better than the original. Local mechanic wanted 90 pounds for a new key, Peugeot themselves wanted a whopping 287 pounds for a new key. What the hell? I ordered a replacement on Amazon for less than 10. Also lots of kudos for the transponder chip. I honestly thought I just needed to put the pcb over in the case and be done with it. Glad I watched this video first :)

[@aaanton11]

Well done! Thanks for the great information👍🏻👍🏻🛠

[@jackparappally7202]

Hi just wondering how do you fit those button ?

[@rogerpetts1193]

After buying a key fob from you and watching your video you saved me a lot of money. Did not realised about the decoder in the fob. Thanks for your service.

[@aaanton11]

Thanks Roger for the great comments👍🏻👍🏻🛠

[@fraind6894]

Came across this just as I was going to get a mobile mechanic to come look at my car. turns out I just had not moved the transponder over to the new key. life saver as said before

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@mrturbill1972]

Really useful video and thanks for information about the transponder. I have to change my wife’s uncle’s Toyota Aygo key fob later on today.

[@aaanton11]

It’s a nice little job and makes a massive difference if your key is damaged it feels like a new car again Thanks for the great comments👍🏻👍🏻🛠

[@trucker_lukew]

Just replaced my keyfob successfully thanks to your video. Appreciate you taking the time to do it!

[@aaanton11]

You're welcome! Thanks for the great comments👍🏻👍🏻🛠

[@colinlane636]

Great video, I changed the wife’s fob as it was worn out. I completely missed the transponder and was scratching my head as to why the car wouldn’t start.Thanks to your video and it’s great detail the problem was soon rectified.Many Thanks

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@leesslotcars]

Cheers mate, i put a new case on my daughters key and the car wouldn’t start so I put the old one back on! Didnt know about the transponder, I do now!!

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@drmarjwilson4919]

Thank you for this. Followed your advice and fixed the key without garage hassles. 10/10

[@aaanton11]

Glad it helped, Thanks for the great comments👍🏻👍🏻🛠

[@smithy4121]

Thanks my daughter just got her first car and it has a button missing on the key so ordered the replacement key case. This will be my job when I get back from work tomorrow

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@fidsta30]

Excellent video thank you - just got a 107 for my daughter that had the exact same issue! Your tutorial is really helpful

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@JonRavnNielsen01]

Thank you for this video! You made it so easy and quick to do and you saved me about 70 euros!

[@aaanton11]

You're welcome! Thanks for the great comments👍🏻👍🏻🛠

[@andrewpatterson189]

Thanks for this. So helpful. Mine was falling to pieces. Was going to buy a duplicate, but thought for 4 quid, I'll give this a go. Now have key in new case, new battery and it works better than ever before. Transponder was a tight fit, but got it in. Works perfect. Thanks for your videos. They have been so useful with this car that seems to have many common issues, like the indicator (my friend's one had this too). Also Sheffield based, take care!

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@eppenga]

Thanks to you I realized why it didn't work at first time, the transponder :)

[@aaanton11]

Glad I could help! Thanks for the great comments👍🏻👍🏻🛠

[@kzzinsky]

Thanks for this video - I’d ordered a new case that didn’t quite fit between the sides, and I didn’t know what the transponder was, so this has given me the reassurance I needed to swap over the whole thing!

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@luigifierro6435]

Hallo from Germany. Thank you sooo much for this video!!!!!!!!!!!! It all worked perfectly and I am happy!

[@aaanton11]

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

[@grahamwhittle1971]

I just got a 107 this channels great love it just ordered a new key box from Amazon il just follow your video 📸.

[@aaanton11]

Welcome aboard! Thanks for the great comments👍🏻👍🏻🛠

[@johndenison9291]

Good, to the point, video on how to replace the key case on a Citroen C1. The little screw needs to right sized screw drive because it was a little fiddly to to remove. I used a drop of releasing fluid. The price of the replacement that he quotes has gone up to £7.99.

[@aaanton11]

Thanks for the great information👍🏻👍🏻🛠

[@MA-yq3nd]

My button fall out same as in video, So I bought new copy case from ebay. It used to work fine but recently it wouldn't lock or unlock the doors. I thought it was the battery but it was the hard copy case. I opened it may times to fix it. When the chip was out of phone it worked nice. So I knew it was the case. Original button were soft and easy to press and new case were hard to press. So I found a small hack to make copy case button work better then the original.

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@RomySews]

Thanks for this, I couldn’t work out how to get the key out but just wasn’t pulling hard enough! 😆

[@aaanton11]

Glad I could help! Thanks for the great comments👍🏻👍🏻🛠

[@cathayy1]

thank you so much for making this video when I bought my car the buttons on my key are held together by selotape and when I tried to peel it off the buttons go with it! definatly be sorting this out asap

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@TanvirKhan-r5o]

Once again a proper informative video thankyou

[@aaanton11]

Glad you enjoyed it Thanks for the great comments👍🏻👍🏻🛠

[@TheFlowWithDaniShow]

This worked perfectly, thank you!!

[@aaanton11]

You're welcome! Thanks for the great comments👍🏻👍🏻🛠

[@fuckracistsnob3]

Great video! Always love watching your videos, even if I already did something or know about it, it's just a fun watch. Replaced my standard key with a flip key for a tenner, for the fun of it haha

[@aaanton11]

What flip key did you use? I would love to see it do you have a link thanks for the great information 👍🏻👍🏻🛠

[@fuckracistsnob3]

@@aaanton11 Excuse the late reply mate, I'm in The Netherlands so I only have the Dutch site for you, but, from the picture you can at least tell what kind of flip case you would need in order for it to work! When I got it they had them on sale for 10,95 each. www.auto-sleutel.nl/peugeot-2-knops-klapsleutel-ombouwset-sleutelbaard-met-inkeping-zijkant?gclid=Cj0KCQjw3qzzBRDnARIsAECmryoy1d-7aZeHf7WbMxGQ7ejn2IdqmDl9MiN4IRjd31Ew7Z2-qY6WshoaAueQEALw_wcB Works great for me, and doing it was 5 minutes work.

[@hughvb]

Fished my transponder out of the bin, thanks to this video…

[@aaanton11]

well done 👍 Thanks for the great comments👍🏻👍🏻🛠

[@Kosmos-77-]

Saved my day, missed the transponderchip! Luckily i didnt throw it away. :)

[@aaanton11]

Good call! Thanks for the great comments👍🏻👍🏻🛠

[@livinupyourself6232]

Very helpful. Many thanks for making the video.

[@aaanton11]

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

[@mack.3740]

Very good video, helped me a lot. Thank You.

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@martinlimon3589]

Awesome information, Thank you

[@aaanton11]

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

[@Gru-n3c]

Great video. Thank you so much

[@aaanton11]

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

[@lap112nguyen5]

so touching for an excellent video

[@aaanton11]

Glad you enjoyed it Thanks for the great comments👍🏻👍🏻🛠

[@RaChEl1597]

Great video! Do you have any idea why the buttons might not work in the plastic casing but will work when using the PCB alone? Changed casing (including moving transponder over) and battery but no different. Sorry to ask but am out of ideas ☹️

[@aaanton11]

Do the old and and new cases match up well, or is the new case not moulded correctly the inside where it meets the buttons, Thanks for the great comments👍🏻👍🏻🛠

[@nicolerodrigues8568]

Thank you so much! 😊

[@aaanton11]

You're welcome 😊Thanks for the great comments👍🏻👍🏻🛠

[@D_W_Pilcher]

I threw away the old fob with the transponder, luckily it was still in the bin. Only realised when the car wouldn't start and managed to flatten the battery trying to start it lol. Wish I knew this prior to changing the casing.

[@aaanton11]

😂 lucky escape, Thanks for the great comments👍🏻👍🏻🛠

[@olitonottero7620]

super helpful thank you

[@aaanton11]

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

[@roundhousetrainspotting]

Great video. Why on earth is the transponder separate???

[@aaanton11]

Good question! Thanks for the great comments👍🏻👍🏻🛠

[@MonkeySmoothy]

Thanks, very helpful!

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@SRPC21]

This is great put my issue is that I put my car key in the wash by mistake and that's why the buttons don't work! (it'd be water damage to the circuit board rather than the physical buttons themselves). Dealership it is for me!

[@aaanton11]

The buttons will be corroded inside, it is possible to desolder the buttons and replace them but its not easy, Thanks for the great comments👍🏻👍🏻🛠

[@underdogunchained]

Great content. My Citroen C1 key blade is worn. It no longer allows manual entry of the front doors. It must be the key because the spare key still allows manual entry. Have you ever needed to get a new key blade cut? And if so, what would be the best places to get this service? Any ideas?

[@aaanton11]

Any good locksmith, or Timsons at sainsburys then swap the transponder Thanks for the great comments👍🏻👍🏻🛠

[@RACMRACM-jl2lj]

brilliant thank you very much!

[@aaanton11]

You're very welcome! Thanks for the great comments👍🏻👍🏻🛠

[@awantamta]

Great job !

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@bear2097]

Hi Anton, I'm looking to install remote keyless entry onto my Peugeot 107 - it's a 2011 reg with central locking but not remote keyless entry. Do I need to buy a kit off Amazon/ebay and wire it in or can I just buy a fob and programme that please? Thank you!! :)

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@WalidFeghali]

I tried replacing the battery, and the main case, and pulling out the little gray chip and putting it in the new one - nothing's happening when I try click open or close. Also the car won't run for more than 1 second (ECU immobilizer?) when I use this key fob now to start it. What should I do? Thanks, W.

[@aaanton11]

Was the car starting before you tried to replace the battery, Thanks for the great information👍🏻👍🏻🛠

[@WalidFeghali]

@@aaanton11 Got it working now, some loose connections in there! Thanks

[@Naheam86]

@@WalidFeghali How did you fix it? Exactly same issue. i changed over the transponder and everything but car will not start???

[@תמרברשלום-ג4צ]

Hi Anthony, thanks for the video! it is my first time trying to do that.. I put the little gray chip in the new case as you showed - nothing's happening when I try click open or close. Also the car won't run.. I have a guess that it might be because of that my new battery has a build in connected little " chip" of its own and it goes just above the place of that "old" chip.. I will add a picture to show...Should I remove it somehow? What should I do?

[@aaanton11]

did the doors unlock & the car start with the old key before dismantling?

[@bigred48]

I recently picked up a C1 2011 with two keys. The centrol locking works with both keys,but they are not push button remote. How do i get a a remote central locking button case? Kind regards Lew.

[@aaanton11]

Sounds like you might have an aftermarket central locking system fitted, you could upgrade that to a remote system Thanks for the great comments👍🏻👍🏻🛠

[@bigred48]

@@aaanton11 Thank you my friend

[@kevinhancock4064]

A question . If internals are changed will the key need pramming ? I don't mean transponder. I mean pcb ? Cheers

[@aaanton11]

No need to program if the pcb is swapped. Thanks for the great comments👍🏻👍🏻🛠

[@kevinhancock4064]

@@aaanton11 sorry I mean key internals

[@mrt4409]

My keyfob on the C1 has stopped working, I put a new battery and re synchronised still no joy. Any suggestions?

[@aaanton11]

More than likely it will be One of the buttons has become detached from the circuit board might be worth using a soldering iron and just touching the contacts to renew. Thanks for the great comments👍🏻👍🏻🛠

[@AlbertJack-UK]

hi brother i have toyta aygo car key remote but i want to convert my remote to another remote like i want to modify my key remote is that possible to convert?

[@aaanton11]

anything is possible ! Thanks for the great comments👍🏻👍🏻🛠

[@OhForAnotherShez]

I'm another guy whose replacement wouldn't snap shut AND learnt about the transponder.🙄 thanks WAWAW?

[@aaanton11]

😂Thanks for the great comments👍🏻👍🏻🛠

[@kelso1286]

Right. I'm planning on doing this myself knowing the garage charges about £100....

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@davidyiu1303]

hi Anton, I threw away my damaged key fob with the transponder chip in it, my car won't start. How can I get a new transponder chip ? Do I need to reprogram it ? Appreciate for any advices.

[@aaanton11]

Yes, you can use a good auto lock smith, the aa also have a mobile service if you are a member, they will reprogram a key at you location. Thanks for the great comments👍🏻👍🏻🛠

[@davidyiu1303]

@@aaanton11 thank you 🙏 I give AA a try😁

[@davidyiu1303]

rkjbfrhfscjkdsjbksdfdfsjdss

[@johnswift500]

Do city bugs use a lot of engine oil , my son did a oil change 5000 miles ago now the oil lights on and hardly any oil on the dip stick

[@aaanton11]

They can use up to 1 L of oil every thousand miles this is an acceptable amount of oil usage I would always recommend check in once a week Thanks for the great comments👍🏻👍🏻🛠

[@johnswift500]

Thanks that’s a big help

[@izziesmith4588]

Why is my Citroen c1 2008 not have remote locking? Can i change this?

[@aaanton11]

some don't have it fitted, Thanks for the great comments👍🏻👍🏻🛠

[@robfunk7325]

Hi Anthony, I watched your video you posted a couple years ago about your mavic air flyaway. I am wondering if I could talk to you about how you got them to replace your drone. let me know if you are available.

[@aaanton11]

I am always available to help, The video you need to watch is this one kzbin.info/www/bejne/iGGbh6SooZdjfNE , I have the complete saga vlodgged in this playlist if it helps, kzbin.info/aero/PLXsfAZuNUCg83S9l1WCoMacrqiD1AXIRQ, Thanks for the great comments👍🏻👍🏻🛠

[@robfunk7325]

@@aaanton11 Thanks, I will go through these

[@EXGLMeverts]

good to see

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@AUTOMOTATE]

New case came shut and I can't get it open any ideas?

[@aaanton11]

Pop a screwdriver in the side and twist, Thanks for the great comments👍🏻👍🏻🛠

[@AlizaShorts]

Can we convert this same key to flipkey?

[@aaanton11]

I will look into it, Thanks for the great comments👍🏻👍🏻🛠

[@mattcoops82]

Bought one off ebay which was compatible with the original key fob back (i.e. the bit with the logo on) its one of the top results when you search "toyota aygo key fob" sold by palison_123 Not sure if this is helpful to anyone but thanks for the video!

[@aaanton11]

Thanks for the great information👍🏻👍🏻🛠

[@petebaker5369]

Thank you for the information, I will try this!

[@petebaker5369]

I bought from palison_123 as well and it fit my toyota aygo (2011) key fob too!

[@lajosbakk3317]

Well my ke its stoped lock the doors, its open perfectly but not locking. Also if you try to push the key in 80/20 its not going in all the way...

[@aaanton11]

Check the connections on the pcb like I do in this video kzbin.info/www/bejne/nZCYZImBm52tmbc Thanks for the great comments👍🏻👍🏻🛠

[@johnbrennan7175]

I have watch so many of these key case replacement videos and I have yet to see anyone of them follow static prevention procedures. Anyone who work within the electronics field know that modern day electronics understand that static electricity is your biggest enemy which can cause serious damage to most electronic components. Simply touching circuit boards without taking precautions can and often will, badly damage the ICs. i.e. remote car keys....

[@aaanton11]

Never had an issue, Thanks for the great information👍🏻👍🏻🛠

[@grib2]

Does this link still Apply 2023 ?

[@aaanton11]

amzn.to/3RrBmtb here is a new one Thanks for the great comments👍🏻👍🏻🛠

[@micheals1992]

I'm guessing if you really wanted you could swap the logo from the old key assuming they're identical fittings

[@aaanton11]

sometimes they fit, others have tiny differences, Thanks for the great comments👍🏻👍🏻🛠

[@Summit_Up_There]

Hahahahahahahahahaha im a tosser. I thought that transponder chip was just a bit of broken plastic so I chucked it! Ffs guess who's going through the bins tonight and guess who's paid for a taxi to work because of it!

[@aaanton11]

Oh no!! hopefully you can find it, Thanks for the great comments👍🏻👍🏻🛠

[@Summit_Up_There]

@@aaanton11 found it. Bought the car last week. The radio didn't work I checked the fuse at the back of the radio and there isn't 1, so bought 1 to fit and it didn't go in.... Turns out they don't have a fuse at the back, so I changed the fuse in the speedo for the radio and still no luck.... After some more digging F7 in the fuse box under the bonnet controls interior light, radio and somthing else it was missing!! I put a 15 in and boom everything works. Left the car for an hour whilst I changed the battery in my fob and chucked that bit of plastic lol, it didn't start. So im panicking thinking of blown another fuse.... This video and that bit of plastic saved me 💪👍

[@aaanton11]

well done all good now, happy motoring, Thanks for the great comments👍🏻👍🏻🛠

[@AureaIris]

I did this without youtube. I didnt transover the little plastic chip. Then panicked because my car didnt start. Called the roadside assistance and they fixed it. NOTE TO MYSELF WATCH A KZbin VIDEO FIRST

[@aaanton11]

Thanks for the great information👍🏻👍🏻🛠

[@MTMMotorServices]

nice video, done a few of these, those buttons are terrible for falling apart. cool Chanel, i've recently started my own with similar type videos. check us out if you get a chance, thanks

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠

[@anhnguyenthi403]

so touching for an excellent video

[@aaanton11]

Thanks for the great comments👍🏻👍🏻🛠