Gm Silverado Sierra Transmission Mount Replacement 2014+

If you have found this video helpful, and you wish to donate to me, follow this link!! its easy!!
paypal.me/aaronhinesauto?loca...
Follow this channel on twitter for the latest content updates and weekly Automotive Tips!!
AutoHines?lang=en
In this video I show the steps and procedures necessary to replace the transmission mount on a Chevrolet Silverado. The same procedures can be taken for a GMC Sierra. Chevrolet suburban. Chevrolet Tahoe. GMC Yukon. And a Cadillac Escalade. The vehicle shown in the video is a 2015 Chevrolet Silverado with 102,000 miles. Symptoms were allowed audible clunk when downshifting, accelerating from a stop, and applying the brakes are low speed’s, I do recommend you purchase a OEM genuine GM mount. I have many had Many difficulties trying to fit in use in after market now from array Lee’s, Napa, and advanced auto parts. I hope this video has help you out if it has please like and subscribe. If you have any questions or comments feel free to leave something in the comment section. Thank you
transmission mount used in this video:
amzn.to/2XomUDf

[@jasoncolahan1033]

Bro…perfect narrating over the work you were doing. Especially the part about the wood!!!! Thanks man!

[@dateatorjr9671]

3 years out of a trans mount, wow. And it doesn’t even plow. Thanks for another great video!

[@AaronHinesAuto]

ya no kidding! thanks for the kind words! and thank for watching

[@JoseDiaz-qs2op]

your video really helps, thank you

[@kickemassicus]

Great video, no fluff just meat and potatoes

[@sergios.delpilar7020]

Thank u ...its really informative...keep the good work....God Bless!!!!

[@adewey33]

Thank you. I might as well replace this mount while replacing the driver side engine mount My car is 2014 Chevy Suburban LT 1500 2WD Rear

[@Chrismckinney1]

I just did my Tahoe’s engine mount. How did you fair with that job.

[@darianthompson5975]

Great video

[@jjgaming6772]

Yo!! Thank you so much I believe this pertains to 2000s and up rwd for this style mount saved my driveline with this worked for a 06 SWB 1500 used a iron plate that was plenty wide enough to lift came right up even re-alligned my exhaust to where it is supposed to be much obliged!

[@MrInternational716]

Thank you!

[@kaptainCream97]

What was the truck doing before replacing?? I have a 2014 Sierra 1500 and when I slow down to about 10mph it jerks and it shifts a little hard

[@Aquatic_Amigo]

Is the Gmc 2008 Sierra that same way to change the mount ?

[@janc9125]

Does anyone have the torque spec for the nut that goes through the crossmember? Mine has come loose twice now, I get a squeak each time.

[@jaredcorser3372]

Man I have been beating my head trying too figure out why my truck was shacking checked my trans mount it's broke in the front cus my check engine light want on so I was like wtf checked it mines cracked thank u I willing to bet that's my problem

[@josebarajas2857]

What do you mean the after market part doesn’t work the same?

[@audirx8]

Was there any viabrations caused from the bad mount? Shaking on the hwy or anything

[@AaronHinesAuto]

yes high way speeds and upon shifting.

[@EduardoRamirez-du4tx]

Hey bro when you're putting on the motor mounts and the transmission one is it better doing it one by one

[@dubsey98]

Oh yea one at a time using a jack and block of wood carefully at the minimum!

[@marcus7980]

What usually causes the trans mount to break? I watched your vid and replaced mine but am wondering if I could have done something to prevent it?

[@drew5992]

Wear and tear

[@josejuan61]

Yeah ! The ratchet works better ;)

[@TuneInBurnOutTV]

Ho w did you know it was bad? What symptoms? Trans slop a stop and go?

[@AaronHinesAuto]

yes, stop and go slop and heavy thud when downshifting to pass

[@TuneInBurnOutTV]

@@AaronHinesAuto I have been trying to track down a similar issue with my l460e in my 14 4x4 sierra. I have a vodeo kimicing the noise shifting. Usually once its warm its noticeable.

[@coolasscoleo]

Mine was a sqeek!!

[@Cre4ture_official]

Did you ever find out what it was? Im currently having this issue, 2015 silverado 5.3 4x4 clacking noise when creeping in 1st gear. In rhythm with the idle. @TuneInBurnOutTV

[@MollyBrown8]

The 2003 Sierra manual transmission does not have enough room to lift. The crossmember has to be removed.

[@AaronHinesAuto]

That’s a bummer. this video is for This video is for 2014+

[@ShawnS.41405]

Molly you jack up the transmission just enough to get the old transmission mount out and put the new one in and let the jack down

[@guitarguy3221]

@@ShawnS.41405 yeah i was thinking you didn't need to remove the xmember on the 99-06. I'm gonna use 2 steel plates and washers bc my poly replacement mount broke after 3yrs. My crossmember Is warped around the bolthole

[@axgibsonprs27]

Thank you!

[@AaronHinesAuto]

Your welcome!