Airgun - Install Altaros regulator and quick fill to AirArms S400

[@antoniocoppola2059]

hello watching the video when you go to unscrew the brass tube inside there is the spring and the spring guide which would be the holed washer but I saw that when you remove the holed washer it is not there, if in the case I mount the regulator you have to put the washer or is there no need?

[@antoniocoppola2059]

hi, I wanted to know if only the pressure regulator is mounted, does the rifle read the pressure from the tank gauge? or does it read the regulator calibration pressure?

[@AirgunRegulator]

after installing only the regulator, the gauge on the rifle shows only regulated pressure

[@antoniocoppola2059]

Hi, in a few days I want to buy from you the pressure regulator for the air arms s400 4.5 rifle less than 7.5 joules together with the pressure gauge that reads the tank pressure, but I saw that there are three regulators that mount on the air arms s400, including the beach classic regulator, HFT 500 and sporter precision, I wanted to know which one you recommend and which one is the most suitable and the most performing. Then the setting must be at 90 bar thanks.

[@fabiopapa2819]

this regulator does not need the hole on the air tank?

[@AirgunRegulator]

No, this regulator not need driling hole to air tank. Installing and uninstalling can be done without permanent intervention to Airgun.

[@Odysseuss.]

What size allen key for barrel band? please

[@AirgunRegulator]

We used 2mm allen key

[@heinkelA2]

Hello. Can I install this to my Air Arms S510 unregulated Rifle. It is 13 years old. Many thanks from Ireland.

[@AirgunRegulator]

Yes you can. The video shows a 12-year-old AA S400

[@alanbray3448]

Did you fit reg to rifle and what were results ,thanks

[@jbsomdeirece2146]

Será se presta?

[@cob7616]

What is that spray that you’re using?

[@AirgunRegulator]

Coyote Silkal 93 but any other silicone spray can be used

[@juniorjuninho4917]

Bom dia Como chama e Onde encontro essa peça com o manómetro para medir a pressão do cilindro?

[@ade14299]

Does the same apply when fitting to HFT500?

[@AirgunRegulator]

yes it can be installed in HFT 500

[@ballkeeper6662]

what results did you get from fitting this kit ?

[@AirgunRegulator]

always depends on the specific parameters of the rifle, but some results we have on our website: www.altaros.cz/en/Air-Arms/115-7512-air-arms-s410-beech-classic-regulator.html#/69-awpdetails-

[@richardjones2811]

Wish I bought this instead of the Robert Lane Regulator. The supplied standoff collapsed and now it's useless and can't be used.

[@garrymatthews5598]

I have a s400 tank with reg fitted and sold the rifle but had to replace with a new tank. It’s all up for sale.

[@richardjones2811]

@@garrymatthews5598 I had a spare air cylinder so just put that on and have forgotten about the reg cylinder.

[@vainparasite]

That’s really sweet👍👍 could you fine tune the reg to adjust power ?

[@AirgunRegulator]

generally, a regulator of physical nature it doesn’t allow you to increase power, just reduce it. The power limitation is in most cases in the form of a small hole or channels through which pressure is applied to the barrel. Increasing them can achieve greater power.

[@vainparasite]

Airgun Regulator thanks for the info I’m new to pcp airguns so any new info is great. I’ve seen on some regulators that a hole has to be drilled in the rifle somewhere, why not for this type or did I miss this? Thanks again Martin

[@AirgunRegulator]

@@vainparasite this type of regulator is the only one on the market that does not require the supply of atmospheric pressure This makes it unnecessary to drill a hole in the airtube and potentially destroy the airgun if this is done wrong or if the airtube regulator does not seal properly.

[@vainparasite]

Airgun Regulator that’s awesome

[@phillipsharpe6459]

What's the point of two air gauges, none as far as i can see , the one you put on is in the more dangerous position as you have to look down the barrel to see it ?

[@AirgunRegulator]

After installing the regulator, the pressure gauge on the rifle shows only the regulated pressure, so it practically shows the same pressure all the time and it is not possible to determine the pressure in the airtube, which is, for example, need at fill the airtube. Another reason is to know how much airtube pressure is left. If a user look from the side and not directly into the barrel then is safely.

[@MilspecPanda]

Does the Air Arms Classic regulator you sell on eBay work for my 30 foot pound FAC TDR? I don’t want power to go down after installing.

[@AirgunRegulator]

If your rifle reaches 30 fpe at a usable pressure (130-150bar) then the power change should be minimal after installing the regulator.

[@Gw0wvl]

Good video but Awfull un- needed music .. ruins the video 👎

[@fabiopapa2819]

I send email