Gas Training. Ideal Logic. How to use service mode or Engineer mode. Ideal Boiler Gas Engineer talks us through the service settings.
Пікірлер: 24
@mushiemiimii Жыл бұрын
Thank you so much! Our Combi c24 won't heat up randomly. The receiver gets the notice but the boiler stops firing up. Error L2, Finally know the reason now! 🙌🏼🙌🏼
@Makillaveli Жыл бұрын
What’s the reason? And were you able to fix it? I’ve currently got the L2 error in the C24
@SD-Plumbing-Heating2 жыл бұрын
Does it tell you how to do this in the manual? If not, why doesn’t the manufacturer put it in there.
@experienceb4bob2 жыл бұрын
Very informative and brilliant
@paulyoung61652 ай бұрын
Hi Allen How do you change the boiler set up from Nat Gas to LNPG once the adaptor kit has been fitted and installation is completed. thanks
@jameshawkins52802 жыл бұрын
Another video 2 in a night from Mr ideal great job 👏
@davesaxon73482 жыл бұрын
Great video, thanks for the info👍🏼
@vasilvlasov65856 ай бұрын
Hello Allen, do you know if there is a setting on ESP1 to set the initial fire up settings to its lowest possible modulating range? When my boiler starts in the morning until the CH system is up to running temperature it modulates perfectly, however once the system is hot, it cycles too frequently and the issue is that every time it fires, it fires at maximum output (i can judge by the noise) and in 10 seconds exceeds the initial set flow temp which forces it to switch the burner off without even not having the chance to modulate down to lower output. Then temp drops by 10 degrees almost immediately. So i was thinking if i can force the boiler by default to start at its lowest temperature this might prevent these short cycles. Great video and explanation of all the settings. Thanks, Vasil
@ciaranclose1922 ай бұрын
How do you range rate an ideal logic plus 30... cant see it anywhere
@YoutubeHero6662 жыл бұрын
cool cheers for the info
@T-rex-s6z Жыл бұрын
I have just had the same boiler installed but the problem is that the tap need’s fast flow before the boiler warms the water ,Does anyone know to get the boiler to come on with the tap running slower Thank you.
@outlawmorga2 жыл бұрын
Hi Allen, have you ever replaced the PCB on the ideal logic and set the parameters of which version of logic you are installing it onto?
@redrum4100 Жыл бұрын
Thanks for saving me
@joshdouglas17672 жыл бұрын
I’m using vf code how many times should I be able to do it for it to work ?
@WEYHARRY1 Жыл бұрын
Brilliant thanks
@patmartin9727 Жыл бұрын
How can I tell if my boiler has enough water in the system
@suj1945 Жыл бұрын
Look at the pressure gauge
@TameraLovesGod Жыл бұрын
Hello what does it mean if L2 shows up?
@RedCyanPhotos Жыл бұрын
How do I remove service mode cos it’s stuck? No one can do it & I’m frozen!
@RedCyanPhotos10 ай бұрын
Same again, please someone help me!
@SydNyd Жыл бұрын
My boiler keeps making a loud drill like noise, it happens randomly. Can anyone explain why? It's extremely loud when it happens
@pradeekund Жыл бұрын
I thought it was happening only for me.. anyone figured out the issue ?
@AllenHart99910 ай бұрын
You would be best to call Ideal Boilers for advice. Thanks.