Annealing PRIMED brass. THIS IS STUPID, DON'T DO IT!

  Рет қаралды 37,462

Erik Cortina

Erik Cortina

2 жыл бұрын

Visit my website:
www.shootsmallgroups.com/
Sign up for my private forum to learn about reloading, wind reading, long range tactics, and more.
www.shootsmallgroups.com/comm...

Пікірлер: 224
@duggydo
@duggydo 2 жыл бұрын
I actually didn’t realize primers packed that much of a punch. Good video Eric.
@jean-francoisavon62
@jean-francoisavon62 2 жыл бұрын
How many primers you guys are storing in the same container box? :-)
@andyd2960
@andyd2960 2 жыл бұрын
I light up a shotgun primer out of curiosity once. Quite a bit of energy in those little guys. They deserve respect.
@oldgoat1890
@oldgoat1890 2 жыл бұрын
@Jess Hadlock I had a factory 7.62x39 (Wolf) with no powder drive bullet up he barrel a couple inches.
@jmkhenka
@jmkhenka 2 жыл бұрын
@Jess Hadlock small rifle primers in my grendel just moves the bullet 2-3mm. Small rifle primer in the 22 hornet lodges the bullet 5-6mm in the bore. Easily knocked out.
@fountainofjewelz1844
@fountainofjewelz1844 2 жыл бұрын
This wind is really windy! LOL Love it, sounds like something I would say. Great science today guys!
@Squat5000
@Squat5000 2 жыл бұрын
This is an amusing test. I've been there done that too. Got a bunch of factory primed brass that got mixed into a batch I was annealing. Definitely got my attention
@donbarile8916
@donbarile8916 2 жыл бұрын
Edwin Sarkissian called, he said, "Cabron. Hold my beer."
@PrecisionRifleNetwork
@PrecisionRifleNetwork 2 жыл бұрын
This was so much fun!
@meklu
@meklu 2 жыл бұрын
Your brass space program is looking quite promising!
@gregisaacs7091
@gregisaacs7091 2 жыл бұрын
Yep, I did it too also by accident. I had just built a nice annealer and annealed about 300 pieces and thought that was all my brass but then found another 101 in their respective cases 50 in each with 1 floater ( score, thank you Lapua!) Well after 50 cases I had grabbed the floater but because it was laying on it's side I noticed that the primer looked real clean. Then I noticed it was unused. I immediately shut the gas and checked the cases I was about to anneal and yep they were all primed. Then I checked out the ones I had already annealed and began thanking the Lord for His mighty hand of protection because everyone of them had a new primer. I couldn't believe it. So yeah, sometimes smart people do stupid things. Actually everyone does just hopefully not too often.
@maxcoatlhunter4322
@maxcoatlhunter4322 2 жыл бұрын
Great and entertaining video. Those primers have lots of power for sure!
@billyarnold5467
@billyarnold5467 2 жыл бұрын
Man that was the wildest crazy video I have ever seen. Thanks. I loved it
@jean-francoisavon62
@jean-francoisavon62 2 жыл бұрын
The difference between boys and men is REALLY only the price of their toys :-)
@GB-zi6qr
@GB-zi6qr 2 жыл бұрын
Thanks for the safety lesson Erik! Much better to see under somewhat controlled conditions.
@davidschmidt5810
@davidschmidt5810 2 жыл бұрын
This is what happens when you mix fire, explosives and distraction. Somebody can get hurt. Thanks for the safety lesson Eric.
@roylandgrave9495
@roylandgrave9495 2 жыл бұрын
This rates, great learning moment in reloading history!
@StewartCountyBallistics
@StewartCountyBallistics 2 жыл бұрын
Great video Eric done in a controlled environment.. it was fun .. these videos are excellent we all get complacent.. this video will help us all !! I would love to see how the brass group's lol be safe my friends
@henryherman9113
@henryherman9113 2 жыл бұрын
Your Videos always bring a chuckle to me..I wish I could find that Anealer here in Canada..Still using that drill and torch method
@theslingandjacket2337
@theslingandjacket2337 2 жыл бұрын
Great video. Experience has taught me to always wear good eye and hand PPE when annealing cases and seating primers.
@joegschwind431
@joegschwind431 3 ай бұрын
Aaahahahah, “this wind, is really windy”…. Good stuff.
@bobcat3905
@bobcat3905 Жыл бұрын
The "GUN SMYTH BUSTERS" LOL That was Great!!
@redleg1013
@redleg1013 2 жыл бұрын
You had me at "This is stupid ". Best way to start a story besides "hey y'all watch this"
@ErikCortina
@ErikCortina 2 жыл бұрын
😂
@darrencsturgis
@darrencsturgis 2 жыл бұрын
I love your videos, I’m a newbie to reloading and your very informative!
@sailorddg9877
@sailorddg9877 2 жыл бұрын
The last six rounds with them tunes, felt I was watching a movie. Keep them coming.
@ShootingAndReloading
@ShootingAndReloading 2 жыл бұрын
I accidentally left a couple live primers in some cases when putting them through my AMP. Having seen your video, I can only count myself lucky they did not go off! Goodness only knows what damage they may have caused!
@jdrollason
@jdrollason 2 жыл бұрын
Erik: "I'm gonna try to catch it" Me: You're going to do WHAT?!?!
@o2wow
@o2wow 2 жыл бұрын
OMG, Eric used $100 worth of primers to do this demo! Fun stuff. I used to put three primers on a 1 foot square steel plate on the floor, they gently put another plate on top of the primers and jump on the top plate. The perfect Monday morning solution to sleepy co-workers.
@tomxiong2207
@tomxiong2207 2 жыл бұрын
I would’ve loved to do that with you guys. You guys had too much fun. Thanks for the info.
@graysontaylor6673
@graysontaylor6673 2 жыл бұрын
Blowing up primers these days is quite the flex.
@johnharris1636
@johnharris1636 2 жыл бұрын
That is a good demonstration of the ignition setup for a 40mm grenade, small amount of powder and a large amount of space. The primer detonates in the pocket and causes the heavy projectile to fly down range. Not really the same with an empty case but the physics still hold.
@MrCherrybottom
@MrCherrybottom 2 жыл бұрын
That was fun to watch. What about a 50 BMG primered casing? We are getting into Demo Land here. LOL
@bryanohalloran9001
@bryanohalloran9001 2 жыл бұрын
Great fun Mate !
@cliffkirby8570
@cliffkirby8570 2 жыл бұрын
That was a pretty ballsy move with the propane tank sitting there LOL
@ronaldperkins4222
@ronaldperkins4222 2 жыл бұрын
Super cool video. With all the theoretical BS on the internet, it was refreshing to see a real life demo of careless reloading processes. Cool! 😎
@stephenthompson9722
@stephenthompson9722 2 жыл бұрын
I believe the flame from the green propane tank is aimed at the base of the case once it's passed through.
@ctech01
@ctech01 2 жыл бұрын
Mom 'ma always said, that inside every grown man was a little boy trying to get out. Well today was your day. LOL 😎 I loved it, keep up the great work, thank You.👍👍👍🤣🤣🤣
@CircleBrewery
@CircleBrewery Жыл бұрын
I’ve set primers off seating them from pressure, and it was like a snap cap going off. After you added heat damn it made a big difference 🎉
@jamesmiller360
@jamesmiller360 2 жыл бұрын
You guys are having too much fun.😁😁
@kriswhitman8027
@kriswhitman8027 2 жыл бұрын
Great video guys. I have often wondered what would happen if I annealed with a live primer....question answered. My induction annealer would not appreciate the launch!
@Dwayne7834
@Dwayne7834 2 жыл бұрын
Thanks this great to know. Thanks for the video and information.
@A-a-ron480
@A-a-ron480 2 ай бұрын
Thanks for doing this for me.
@saleen308
@saleen308 2 жыл бұрын
Yup, learned this the hard way. Fun trip to the ER and had to tell the police what happened while being treated.
@peterresetz1960
@peterresetz1960 2 жыл бұрын
I had primer detonate while seating. First time was in a Dillon 550 loading 38 Spl. Second time was with a RCBS hand priming tool, (shell holder type) priming 223 Rem. Made my ears ring each time. About as loud as a 22LR.
@markRTFGuns
@markRTFGuns 5 ай бұрын
Thank you sir!
@bradleytyrrell4417
@bradleytyrrell4417 2 жыл бұрын
I wonder how much noise that the primer contributes to the report of the actual firearm bast with powder to a round with out powder
@SimpleLife1971
@SimpleLife1971 2 жыл бұрын
Erik, this is what we call "hang fire"! LOL
@danbramley1982
@danbramley1982 2 жыл бұрын
I bet you shit your pants when the first one went off in your reloading room!!! Could not stop smiling waiting for that first one to go off. Cool video.
@ErikCortina
@ErikCortina 2 жыл бұрын
I did it three times. 😂 I’ll tell you the story some time, but it was one of those times that I should have just stopped and went in the house.
@barrygrant2907
@barrygrant2907 2 жыл бұрын
When I was stationed in Alaska with A-10s, a couple weapons guys decided to deprime a 30mm case with a bow torch. Bad idea...
@juliusjames5577
@juliusjames5577 2 жыл бұрын
Makes me cry to see those precious primers being wasted😥
@ewetho
@ewetho 2 жыл бұрын
Worth the fun and information
@juliusjames5577
@juliusjames5577 2 жыл бұрын
Yes, must admit it was like watching a jack in the box for men.
@mrcisme
@mrcisme 2 жыл бұрын
Did I see you guys flinching? Funny! What is the music that you used near the end? I don't often appreciate music in videos but that was nice.
@moitoi4064
@moitoi4064 2 жыл бұрын
This reminds me of my time in Viêt Nam, we had an incinerator at out HQ that we use to burn documents, one night while on watch I threw a handful of 5.56 mm rounds in the fire, it took quite a while (one minute or more) before the rounds went off, I was surprised they didn’t sound as loud as if they were fired out of a rifle, looks like only the primers ignited because there was no compression. Erik, you should try that too. Lol.
@F12Mahon
@F12Mahon 2 жыл бұрын
Love the music for the last five rounds. Not only would the brass hit you hard, it would burn too.
@Privateparry
@Privateparry 2 жыл бұрын
🤣🤣🤣 awesome bit of fun. I was cringing just watching it 🤣🤣
@thetriode
@thetriode 2 жыл бұрын
I made a few primers to diagnose a light strike issue by sticking them in a pair of cans that fit together and heating. it worked but punched a hole in the cans after a few.
@rc7990
@rc7990 8 ай бұрын
I did it also using a an Annealeez annealing system and of course I was standing in front of it when it blew. The case hit me in the chest but the blast is what made me jump. The case didn't even leave a mark on my shirt much less harm me. I will be more careful in the future.
@jeremiah7855
@jeremiah7855 2 жыл бұрын
That was fun to watch
@curtisbacon7856
@curtisbacon7856 2 жыл бұрын
Heard a story of a man who used a 22 cartridge to replace a blown fuse in his old Ford pickup truck for the brake lights the short was pretty significant it took about 5 minutes to shoot him in the leg. And the only reason it took 5 minutes because that was how long it was before he hit the brake pedal
@peterresetz1960
@peterresetz1960 2 жыл бұрын
That was actually the first urban legend test on Myth Busters. Jammie and Adam did get a 22LR cartridge to ignite in a pickup truck under the dashboard fuse block.
@justinvandee2008
@justinvandee2008 2 жыл бұрын
My dad once forgot he put primed pc of brass on fuel stove to heat reloading house. Primer went off and put hole through window like a BB gun
@donalddepew9605
@donalddepew9605 2 жыл бұрын
I was using a hammer type bullet extractor and accidentally had a primer go off. Scared the bejesus out of me. Always pay attention to what you are doing!
@kirkboswell2575
@kirkboswell2575 2 жыл бұрын
The wind was the uncontrollable factor. Reminds me of difficulties I've run into trying to cut metal with a torch out in the wind. I really think that if this had been done inside, the 6 seconds would have been more than enough to demonstrate what happens.
@oldgoat1890
@oldgoat1890 2 жыл бұрын
I was in the military with a guy that wanted an empty 5.56 case. He pulled the bullet, dumped the powder, and put it in a vise. He then hit it with a punch and hammer. Next step was down to the Med canter to get the primer dug out of his shoulder.
@novicereloader
@novicereloader 2 жыл бұрын
My buddy, who is also new to reloading ended up with a bent primer. He decided to take a hammer to it on the garage floor. I had already tested a primer in an otherwise empty case in my gun to see what I was dealing with before I ever loaded a full cartridge. He didn't notice I was plugging my ears. He wasn't expecting that much power.
@ibissga
@ibissga 2 жыл бұрын
I may be wrong, but was the green torch point directly into the case base? It can explain why primers went off after "annealing". Anyway, cool video with a great explanation of why it's dangerous to anneal primed stuff
@pa6552
@pa6552 2 жыл бұрын
LOL - can relate - sort of - went through the chore of getting the correct aztec mode on the AMP, and since it needs to be sacrificed, I was looking for any old brass that could be representative of the batch. Conveniently found one lying in a drawer and proceeded to run the aztec mode. When I was done, and as I put it into the pan I noticed it was primed... I think I was saved only by the length of the brass ( 375 H&H) - shorter cartridge would probably have left stains...
@pa6552
@pa6552 2 жыл бұрын
PS - I think that second torch was still hitting the case after it went to the next station. Anyway - you know what you did with this video - right? You showed "those" guys irrefutable proof that as long as they don't anneal for longer than 10s, live cases are OK - they're gonna use this video as proof... :)
@conunpocodefe
@conunpocodefe 9 ай бұрын
Two kids having fun!
@narc46
@narc46 Жыл бұрын
I recently had two primers detonate in the cooling tray after annealing. I didn't realize I had 2 light strike dud primers that I had disassembled the round weeks earlier that found their way into my spent brass box. When they went off the primer punched a hole in the steel cooling tray, the second ricocheted off the steel table and hit me in the chest. I will be decapping all from now on spent or not.
@terrycole7753
@terrycole7753 2 жыл бұрын
I had that happen to me except my brass was LC 7.62 & primer was (I believe) Winchester & I was in the kitchen with 91/2' plaster ceiling with Bench Source sitting on 3' counter. The ceiling still bears the mark. Timer was set at about 6 seconds & the primer went just as the plate started to turn. I now double check my brass brass before annealing. Ever thought of trying that with the AMP?:)
@graynotescartridgebox
@graynotescartridgebox 2 жыл бұрын
And that was $75 worth of primers.
@lovetoflylovetofly3843
@lovetoflylovetofly3843 2 жыл бұрын
Someone using there last 10 primers....."NOOOOOO". 🤣
@travisweldmaster7815
@travisweldmaster7815 Жыл бұрын
Oh and zero recoil felt in said hammer, lol love the music with it
@ericcorpus7446
@ericcorpus7446 2 жыл бұрын
😯 now go test it out in the new amp annealer. Jk. Very interesting video for sure. Thanks for keeping us entertained.
@stevenrogers4663
@stevenrogers4663 2 жыл бұрын
Lol... I did the same thing but it was in a garage and a piece of the anvil cup cut my leg... I was wearing shorts at the time and it scared the crap out of me...
@altonrowell7854
@altonrowell7854 2 жыл бұрын
Interesting video.
@shootit6144
@shootit6144 8 ай бұрын
Yup done that 4 days It’s a Little more jumpy when there held with a drill in a socket 💥 😂
@romansdzalbs
@romansdzalbs 2 жыл бұрын
Now make them pop with AMP annealer :D loved the part with once again primed brass
@brucemcmillan8750
@brucemcmillan8750 2 жыл бұрын
I had one go off last Dec ,totally unexpected ,scared the crap out of me, usually turn the lights down low to watch the progress and add cases as they rip onto the cooling tray, not sure where the primer went, added a new caution to annealing, always check for primers
@8mmmauser896
@8mmmauser896 2 жыл бұрын
Here we are in a middle of a primer shortage and he does this! SMH
@ajbuschm
@ajbuschm 2 жыл бұрын
I know if you anneal a 6 BR case with an induction annealer it will set off a CCI 450. Learned the hard way.
@patricks7622
@patricks7622 2 жыл бұрын
Haha, that slo-mo "whoooa" sounded something like Godzilla right?
@kingofbrutaltheocracy9201
@kingofbrutaltheocracy9201 2 жыл бұрын
This is why I wear eye pro when I seat primers. They are potent for their size.
@davidbean6053
@davidbean6053 Жыл бұрын
This happened to me last week. MUCH louder than you might think
@alejandroesteves8903
@alejandroesteves8903 Жыл бұрын
just to shoot 22 pellet using 22-250 primed brass, BTW while at it I found the using a single piece of brass I was able to group under 1/6 of an inch groups at 10 yards
@1rukie
@1rukie 2 жыл бұрын
I have done that my buddy was shocked he thought there was powder in the case lol
@ScottFichter
@ScottFichter 2 жыл бұрын
Thanks for the sub man. I love your channel.
@ErikCortina
@ErikCortina 2 жыл бұрын
My OBS game is weak. I had to find someone like you to learn me how to use it. 😁
@anthonymichaelmaui3432
@anthonymichaelmaui3432 2 жыл бұрын
Where can I order your tuner brakes and do they fit on a Smith and wesson M&P 15 I just bought last week haven't shot it yet but planning on doing that soon aloha from Hawaii
@anthonymichaelmaui3432
@anthonymichaelmaui3432 2 жыл бұрын
@@eliasaamot573 ok thanks for the info 👍 aloha
@robertmettler1910
@robertmettler1910 2 жыл бұрын
Like a bunch of kids with firecrackers love it
@greavous93
@greavous93 2 жыл бұрын
when I was a kid we would fill 20 gauge shells with powder and a primer and stick them into plastic airplane models like an F-4 (use two of them) and light them up. The powder burned off like an after burner and the primer would cook off once the model was a molten fiery mess and blow burning ooze everywhere. Probably because we werent into annealing brass yet.
@DanielBoone337
@DanielBoone337 2 жыл бұрын
Them things turned into little rocket ships!!! LOL
@wrstew1272
@wrstew1272 2 жыл бұрын
How big did the primer pockets get after the “test”? Does this mean that you are going to use the electric annealer from now on???
@altonrowell7854
@altonrowell7854 2 жыл бұрын
I usually fill the brass case up with primers and add black powder.
@livingintheLight.
@livingintheLight. 2 жыл бұрын
I ran one through that I missed while fire forming 6arc. Had 12grs of red dot in it. Think peeled back like a banana and scared the piss out of me
@travisweldmaster7815
@travisweldmaster7815 Жыл бұрын
I layed one on my vice one day and just popped it with a 22oz framing hammer, took 2 hits...POW
@audiogod2929
@audiogod2929 2 жыл бұрын
Dude, I thought i was the only one who did that!
@SealSportsMandeville
@SealSportsMandeville Жыл бұрын
LOL! We all do stuff like this...few of us are brave/confident enough to admit it! Depriming and annealing in the same step!
@henryknoetze9579
@henryknoetze9579 2 жыл бұрын
That is exactly right. All the annealing accidents I have ever heard of all happened after the cases dropped from the annealing machine. Those primers pack a punch. They WILL penetrate flesh if ppinting your way
@bobjackson7516
@bobjackson7516 2 жыл бұрын
Not to change the subject, but what happened to Texas Barndos? Everything alright with the company I hope?
@peaceriver7808
@peaceriver7808 2 ай бұрын
Been there, done that!
@pstewart5443
@pstewart5443 2 жыл бұрын
The heat of conduction....took a few seconds for the heat to reach the primer.
@frankiejones4816
@frankiejones4816 2 жыл бұрын
I live near a marine base in California and and they have a war game ever now and then my friends would go our there and pick up unforeseen Blanks and we used to shoot the primers out of a sling shot handle using a flare to heat up the Blanks and we used to aim it at coke (rc) cans and we got really good at aiming it. The primers would go thru the cans and into the broads we used to use as a back stop. That was about 57 years ago. Those primers was. Anyway it had some speed and power. I wouldn't recommend doing in a controlled environment.
@frankiejones4816
@frankiejones4816 2 жыл бұрын
Don't try doing g WHat I did back then. Absolutely don't try it.
@walt5797
@walt5797 2 жыл бұрын
There's the kaboom, that earth shattering kaboom.
@frankspataro9714
@frankspataro9714 2 жыл бұрын
Guy from my work his dad was annealing and primer shot into his hand just this spring
@CHenry1951
@CHenry1951 2 жыл бұрын
Pretty impressive, it shows if you don't pay attention you could get hurt !!
@spysweeper
@spysweeper 2 жыл бұрын
It was interesting!! I was more afraid for you guys being hit by brass shrapnel specially that it has been softened where you focused the flame-at least it was not a closed case!! There’s your 21 gun salute for a reloader!!!😂
Annealing brass. Should you?
20:30
Johnny's Reloading Bench
Рет қаралды 91 М.
I over annealed brass and then F/L sized it.  UNEXPECTED RESULTS!!!
19:02
The day of the sea 🌊 🤣❤️ #demariki
00:22
Demariki
Рет қаралды 53 МЛН
ROCK PAPER SCISSOR! (55 MLN SUBS!) feat @PANDAGIRLOFFICIAL #shorts
00:31
How to bring sweets anywhere 😋🍰🍫
00:32
TooTool
Рет қаралды 54 МЛН
Is it Cake or Fake ? 🍰
00:53
A4
Рет қаралды 19 МЛН
Comparing AMP vs. Bench source annealer | Part 2
13:25
Erik Cortina
Рет қаралды 67 М.
Automating an AGS Annealer
13:55
Corwin Bos
Рет қаралды 3,1 М.
This is how I anneal my brass
19:29
Erik Cortina
Рет қаралды 392 М.
Ugly Annealer Review & Use
8:58
Strickly Reloading
Рет қаралды 3,6 М.
Chasing the lands is STUPID! Don't do it.
20:31
Erik Cortina
Рет қаралды 792 М.
EP 2.0 Brass Annealer for Brass Prep
14:08
F-Class John
Рет қаралды 40 М.
DIY BRASS ANNEALER DETAILED GUIDE FOR ~$100
14:50
Elfster's Rifles and Reloading
Рет қаралды 251 М.
500 yard BlackJack Challenge #11
20:10
Erik Cortina
Рет қаралды 15 М.
To Anneal Brass or Not!
23:38
primalrights
Рет қаралды 16 М.
Art of Time Wasting in Football😅
0:19
SkillerHome
Рет қаралды 7 МЛН
Он круче РОНАЛДО🤯
0:27
Бутылочка
Рет қаралды 608 М.
⬅️🤔➡️
0:31
Celine Dept
Рет қаралды 37 МЛН