Skyler you and Jason are my go to guys. You 2 have helped me the most in learnin my new craft. And i thank you both, some ppl don't say thank you too the ppl that have helped them. So again Skyler and Jason THANK YOU. and RING ON Michael
@CoinRingsfromTheMint9 жыл бұрын
You are the man!
@brettrussell75216 жыл бұрын
thank you for the video, really helpful and thorough. I was doing coin rings years back (way less info out there) and finally decided to get back into it. thanks for all your help on my way.
@CoinRingsfromTheMint6 жыл бұрын
+Brett Russell Ypu are very welcome! Before the info was out there it was very time consuming and difficult for sure. Enjoy all the new tools too!
@66lwmorgan5 жыл бұрын
Good tip, I wondered what the difference was between coins while heating them.
@efman2k39 жыл бұрын
You have really great videos. I was wondering how many times you can anneal a silver coin during the process of making a ring. Thank you for taking the time to post all your videos.
@CoinRingsfromTheMint9 жыл бұрын
Thanks! I always try to limit over annealing. Coins like Franklin halves and I964 JFK'S can be damaged by annealing so I try to keep it to a minimum but that is a delicate balance. But if you feel the coin getting harder, you need to re anneal. I usually anneal about 3-4 time on a difficult coin.
@n1rlu9 жыл бұрын
Thanks for your Videos, Its helped me out quite a bit with the Coin Ring Making process. The info on the 1964 Kennedy Half dollar help me out alot... BFG Custom Coin Rings
@CoinRingsfromTheMint9 жыл бұрын
No problem! The 64's are tricky coins for sure.
@JTCoinRings6 жыл бұрын
You have this down to a science...I can't wait for Forged 2!
@CoinRingsfromTheMint6 жыл бұрын
Thanks! The first part of forged 2 is up. I'm really excited for the book and second video to be released :) kzbin.info/www/bejne/i3nLf4moeMissNE
@justcraig35887 жыл бұрын
Hey, one of the coins you had there was a Dutch Guilder, I just so happened to make a ring out of one of those and it wasn't that hard and I didn't damage my tools. I just didn't quench when I annealed it. I have pictures of you want to see. But great video as alway and keep it up. You were the one who inspired me to make coin rings and I thank you for showing me how.
@CoinRingsfromTheMint7 жыл бұрын
+Just Craig Ahh good move there. I have made a few steel ones but as a general rule I don't. I'm glad you found your way to coin ringing!
@justcraig35887 жыл бұрын
Coin Rings from The Mint - Change You Can Wear Hey man I just looked it up, and they say it's made from nickel? Is that a good material to use or would you still steer clear?
@CoinRingsfromTheMint7 жыл бұрын
Just Craig nickel is hard but still doable for sure.
@justcraig35887 жыл бұрын
Coin Rings from The Mint - Change You Can Wear Ahh well that makes sense then. Cheers for your help!
@RieZZieman9 жыл бұрын
that coin you show at 1:10 is a "rijksdaalder", or 2,50 gulden. It used to be the currency in The Netherlands. The old lady on the coin is Koningin Juliana, or queen Juliana.
@CoinRingsfromTheMint9 жыл бұрын
Right on, thanks for the info!
@KentClark750759 жыл бұрын
Thanks for the torching tips,,, I am in there with Michael, I get a lot of good info from Skyler and Jason... Thanks again...
@CoinRingsfromTheMint9 жыл бұрын
Thanks! I am happy to be a part of helping out.
@joscoins4 жыл бұрын
Awesome video.. about to make a franklin .. it's been about a year since i've done one .. thank's for the refresh course!!
@joscoins4 жыл бұрын
Also could you explain a bit more about the 40%er's?? How hot do they get?? I try to stay between a silver anneal blue flame and a slight orange flame ??
@silvertaniwha13144 жыл бұрын
Awesome and super informative video bud. Thanks for taking the time to explain this part of the process 🤙🤙
@TonyCijsouw9 жыл бұрын
That 'Greek' one, "the one you can't remember right now", is the beautiful Dutch Gulden. From before we got the Euro. There are silver versions as well, 72% silver and 28% copper, I guess those would suitable for making rings.
@fairysox2217 жыл бұрын
If you need to anneal Aluminium I recommend rubbing non perfumed hand soap bar on them, whilst gently heating watch for the soap turning a caramelized color then blackening, stop heating at this point and you're done :
@19Edurne5 жыл бұрын
Nickel is also attracted to a magnet...
@FireEater8 жыл бұрын
Thanks I will try the flux first. By the way thanks for all the great info.
@CoinRingsfromTheMint8 жыл бұрын
You are very welcome
@dolfinmagikpro5 жыл бұрын
Very informative. Thank you. One question ... What about copper coins, such as the British Penny that is about the size of the American Half Dollar? How would you anneal that? Also ... Since Aluminum is already such a soft metal, would it be necessary to anneal it at all? Thanks in advance!
@MerlijnDingemanse4 жыл бұрын
1:00 that´s a dutch gulden, the currency they used before the euro
@marijnspaans81835 жыл бұрын
the magnetice coin comes from the Netherlands
@1wannabee15 жыл бұрын
Can I ask you is it ok to quench the coin in merely plain water or should you use some other solution? Many thanks and... Love your vids.
@CoinRingsfromTheMint5 жыл бұрын
Plain water is all I use.
@joegoedhart12597 ай бұрын
Very interesting but only coin objective, not metal. Could you please google the composition of Au Florin 1950s and Au 50 cent round 1955 and tell me which method is best for these so I dont go ryining my coins?
@laslo679 жыл бұрын
First of all... great videos. They've helped me more than I can express. Now for my question... You always do your heating on a stone/concrete where most of the other videos I've seen are done holding the coins with tweezers. Are there any specific pros/cons to these two methods? Thanks.
@CoinRingsfromTheMint9 жыл бұрын
I usually work off of a fire panel or something. After I saw Jason using the tweezers recently I gave that a try. I don't see any real pro or con with either way. I just can't do it any other way because I have been doing it the same way so long. Actually one pro for my method is that I stack up my non silver coins that I am making for the day and heat them all up at once which speeds the annealing process up. I don't do that with silver because they are a bit more delicate. Thanks for the message! Skyler
@chyrt7 жыл бұрын
lol, that first coin is a coin from my country, a gulden. I live in the Netherlands. we used to use the gulden before the euro.
@CoinRingsfromTheMint7 жыл бұрын
+Geert Perton haha!
@chyrt7 жыл бұрын
I have made a ring out of one like that, But I would like to see you make one too!
@MDogg19603 жыл бұрын
Can coins that are clad in silver or gold be annealed and made into rings?
@Thewaspsnest655 жыл бұрын
To anneal aluminium heat the coin till u can stroke a matchstick on it and it makes a black line. Then Quench
@fig8166 жыл бұрын
Skyler, Quick comment and then a question. First off, I want to say thanks for taking the time to help rookies like me. Now my question. There is one metal combination you did not mention and I was wondering if there are any issues, when annealing a 65-70 kennedy half dollar? They claim to be 40% silver. In reality, the silver content is closer to 36.5%. Have you had any problems while annealing one of these? Thanks.
@CoinRingsfromTheMint6 жыл бұрын
You are very welcome! The 40%ers anneal really well and don't have issues there. The issue with them is that they like to warp when you are bending them. That just requires practice to get better.
@rossbusher1946 жыл бұрын
First, butane or propane. Which fuel is better or does it matter? Second for safety , what is the block you are annealing on, concrete, paver or other. As long as it doesn't burn or damage the coin is there a preferred method?
@CoinRingsfromTheMint6 жыл бұрын
I always use propane. It is important to use a fire brick or something that is rated for fire. I use a fire panel now. Thus video is a regular brick because I hadn't finished setting my shop up at that point. The sand in the cement in that brick is not good for fire. They can pop and shoot stuff in your eyes.
@f43raceleague55 жыл бұрын
You said the 1964 Kennedy was unique. Are all the 90% silver Kennedy half dolllars the same way? I have a 1994-S Proof "Deep Cameo" that I'd like to do. Do I anneal it the same way you showed for your 1964?
@mikeroe92513 жыл бұрын
How do you anneal a brass coin?
@chipwoodin6788 жыл бұрын
Do you have the sizes and dimensions for the punches and dies? I work where we have a machine shop. Thanks for all your informative videos.
@CoinRingsfromTheMint8 жыл бұрын
+Chip Woodin Thanks! Here is the specifics video. kzbin.info/www/bejne/qJaWZmyYfJZnfMk
@johnnyandrew90834 ай бұрын
I have issues with my silver coins getting warped on the reed side. I’m not sure if an annealing process issue or the folding. It’s getting expensive
@thekingofdesksthefirst74432 ай бұрын
I’ve had that same issue. I found that when I rotate the cone while folding the coin it somewhat stops that. Take the coin out of the die when you’re half way folded. If you’re still having that issue, Swedish wraps will solve it for the most part.
@mikeroe92513 жыл бұрын
What do you quench the coin in?
@jlchambe777 жыл бұрын
Have you ever done a Canadian Toonie? I have a Canadian friend whom I would like to make a coin ring for, but the quarters are steel. I townie would be cool, but I'm not sure if the dis-similar metals will be a problem.
@CoinRingsfromTheMint7 жыл бұрын
+Jeff Chamberlain Yeah they separate. The outer ring is also steel. You can go to a local coin shop and pick up a silver quarter or half dollar though. They will also have some nice large cents for cheap. They are all great choices for a ring.
@alexandermishenberg84568 жыл бұрын
Thanks and what about press?
@brianthornton83125 жыл бұрын
Very informative 👍
@karlseel8159 жыл бұрын
Very good tutorial
@CoinRingsfromTheMint9 жыл бұрын
Thanks!
@Dulles-jt6sr5 жыл бұрын
What if you are overheated the coin and it's bubbling.. what can you do about it.. Only throw it away?? 😨
@CoinRingsfromTheMint5 жыл бұрын
No you can always sand it and make it a smooth band.
@hellorusso5 жыл бұрын
Thanks brother!
@hellorusso5 жыл бұрын
Thanks for a great, informative channel. Hey, my Silver Eagle coin rings are coming out with a rough surface. And I start with BU coins. I'm using a torch like yours, with MAP gas. Am I getting them too hot? It's only on the Silver Eagle $1 dollar coins, .999 silver. Really sucks! They look Textured, I do use Sparex and Liver of Sulfur. Could the Acid be doing it. But, the areas where my tools have polished the edge are not rough. I'm lost...
@CoinRingsfromTheMint5 жыл бұрын
It is most definitely the heat. Map gets too hot but I still can happen with propane. Heat it enough to sizzle when you put it in the water but not hot enough to make it change color and you should be good.
@MrSilver97599 жыл бұрын
can Iuse a wing type adapter on the torch ? excellent way of annealling
@CoinRingsfromTheMint9 жыл бұрын
That would be a great way to spread the flame out. I'm sure it would work well.
@MrSilver97599 жыл бұрын
thank you, for comment back !
@CoinRingsfromTheMint9 жыл бұрын
Not a problem!
@dramodt9 жыл бұрын
Can you over anneal a Morgan dollar? It did turn gold. Maybe I shoulda turned down the lights. But anyway, I have it pressed in the die, and cone shaped now, I've re-annealed it a time or two, but seems as if its just too hard, and I can't get it to hammer down on the mandrel.
@CoinRingsfromTheMint9 жыл бұрын
morgans are pretty forgiving as far as annealing goes. They are much harder to bend though because they are so much thicker. Bring it up to a dull red and keep on hammering :)
@scousersummary92338 жыл бұрын
dude your videos are awesome but do you know how to heat treat a coin so that when it has cooled it can be bent with ease
@CoinRingsfromTheMint8 жыл бұрын
+Scouser Summary Thanks! I am assuming you are talking about quenching the coin. It is a common misconception that it hardens them. With non ferrous metals like copper and silver, it doesn't make a difference
@suzannehofer38675 жыл бұрын
Can the current USA quarters (clad?) be annealed? I want to make cowboy hat earrings and am not sure what year(s) of quarter are workable. Thanks for your help!
@CoinRingsfromTheMint5 жыл бұрын
Sure that is no problem.
@FireEater8 жыл бұрын
I tried annealing and not annealing a quarter but once I heat the coin it looses it's silver color and after polished it's not the same bright silver. I even tried a brass wire wheel on a Dremel tool just to see if I could get the original color but not as bright. Maybe I'm doing something wrong.
@CoinRingsfromTheMint8 жыл бұрын
You can either use Flux to keep it from happening or you can use a pickle (an acid bath) to dip it in when you are done.
@jonwaters52787 жыл бұрын
Long time watcher first time question. I've noticed you anneal flat, and other people use long nose pliers. Is it due to misshapen coin ring after the first anneal?
@CoinRingsfromTheMint7 жыл бұрын
+Jon Waters Haha great question. Both ways are great. I think what it is, is that some people lean more towards Jason's works method and others tend to lean towards mine. You can usually tell which by how they anneal :) Both methods are great and probably a hybrid of the two is best
@5150roc9 жыл бұрын
A lot a great info thanks
@CoinRingsfromTheMint9 жыл бұрын
You are welcome!
@cfvettes7 жыл бұрын
I tried to make my first silver quarter ring. 1964. I annealed it and then deburred the edge. It folded with no problem but when I flipped it over to stretch out the other side, it snapped and split as it was almost done. I had re-annealed it too. Any idea what I might have done wrong? I've practiced on many newer quarters to get the hang of it and never had a problem.
@CoinRingsfromTheMint7 жыл бұрын
+cfvettes sometimes the deburring tool can leave a little knick if you don't sand it afterwards. It is either that or you were trying to make it too large or had too small of a hole to start with. It has to be one of those 3 I would guess. Hopefully you get it figured out!
@jax86046 жыл бұрын
cfvettes may be 8 months late.. but also try annealing it again
@kevincolwell95756 жыл бұрын
Why? Why does one require so much less heat? I have been trying to make a blade collar for a sword (what the Japanese call a habaki) out of nickel silver. I have heated it to bright red and quenched, and it is not working. Any tips (like less heat or air cool or something)? The small amount of heat on the Kennedy coin looked more like what we smiths call stress relieving, but that would be in iron or steel. I would love suggestions, and even more, to know why. Thanks. good video. You are one of the first people making coin rings where I really like the approach and the work, but I haven't really studied these things, so I am sure I am missing some good craftspeople.
@CoinRingsfromTheMint6 жыл бұрын
+kevin colwell Thanks for the message! I know coins with high nickel content are a bear to bend so I'm assuming you must be running up on a similar issue. The 1964 Kennedy's are really strange so I can't tell you why they are the way they are to be honest. The reason we don't bring silver coins up to a bright red is because the surface tends to get distorted and bubbled up. A dull red is all we look for at most with silver. If it were me I woyld ditch the nickel silver and use some 90% silver 10% copper. That is coin silver. It works much easier but you might need the nickel for extra strength for your project.
@kevincolwell95756 жыл бұрын
damn, I wish i had the benefit of this reply earlier. Thank you for it. I convinced the client to let me go with Sterling. Maybe next time I will use Coin Silver. I have never used it, but that sort of mixture would have been appropriate for Japanese and Chinese sword furniture (they made shibuichi and shakudo, which are silver and copper or silver copper and gold.) thanks a lot
@thekingofdesksthefirst74433 ай бұрын
Does overheating the coin lead to it being more brittle? I just tried to make my first silver half dollar coin ring but it broke in the first die😅, super expensive mistake and I don’t really want to make that same one again!
@CoinRingsfromTheMint3 ай бұрын
. When you overheat a coin usually the surface bubbles or melts. If it doesn’t do that, usually you haven’t overheated it. What type of coin is it and where did you get it?
@thekingofdesksthefirst74432 ай бұрын
@@CoinRingsfromTheMint1964 Kennedy! Ive been holding onto it for a while, came across it at my work.
@dbcrn8594 жыл бұрын
I have no issues with the '64 Kennedys, but the 40% ones are a real pain.
@waynes3474 жыл бұрын
How to keep the quarters from turning dark or black
@CoinRingsfromTheMint4 жыл бұрын
There is no good way that I know of. Cleaning them off with steel wool is what I do.
@holenmyshoe4 жыл бұрын
@@CoinRingsfromTheMint ok.. thanks
@alexandermishenberg84568 жыл бұрын
Skyler! Are you ever made a ring from steel coin or aluminum coin?If it's possible tell us mote about techniqueOr better not to try?Thanks
@CoinRingsfromTheMint8 жыл бұрын
Those are the two metals to stay away from. Steel will damage your punches and dies.
@cosmicgoat99694 жыл бұрын
Why are the copper-nickel coins so hard to stretch on the ring stretcher?
@CoinRingsfromTheMint4 жыл бұрын
Nickel is extremely hard
@cosmicgoat99694 жыл бұрын
Change You Can Wear yeah I realised I just have to anneal more
@floydhelms448 жыл бұрын
Sklyer, I have a crown of thorn coin,(1"5/8) Thinking its bronze and a little thicker than a silver dollar. Whats your thinking on annealing this type of coin?Many,Thanks
@CoinRingsfromTheMint8 жыл бұрын
+Floyd Helms I always get them to a dull red. Be sure to file the cut edge. Many of those coins have high relief and can cause the coin to split.
@tremor11277 жыл бұрын
Hello. Is it imperitive to quench silver coins? I have seen images of old well circulated coins used to make rings that look exactly like they did before they ever started. It is neither polished or "antiqued" looking and I want to make one like that. Also, would you avoid proof coins all together or just proof clads? Thanks!
@CoinRingsfromTheMint7 жыл бұрын
+tremor1127 You might be able to get away with not annealing certain coins but it drastically increases the likelihood of splitting. Proof clad half dollars are the only ones that give me trouble. The silver proof coins seem to work great. Thanks!
@StephenKlineMCM8 жыл бұрын
Skyler, Are there half dollar years I should avoid? I tried a real shiny 2006 and it cracked when I used the sizer. Also, I annealed it and it didn't seem to get any softer. Did I over anneal possibly? Thanks for the great info.
@CoinRingsfromTheMint8 жыл бұрын
+Stephen Kline With us coins they are mostly good. The one big exception is proof clad half dollars. For some reason the outside layer always wants to crack. Over annealing will start to melt the coin. If it's not doing that, you probably aren't over annealing. Hopefully that is helpful!
@MawoDuffer7 жыл бұрын
Don't make them out of new pennies, they are zinc and melt instantly. I think I'll make one out of a quarter on the outside and a nickel inside
@alexanderdavis5332 Жыл бұрын
“HEATED” debates 😂
@NicoleSherwood-Horsemanship7 жыл бұрын
Hi how do you clean the fire scale off the coins?Thank you 😊
@CoinRingsfromTheMint7 жыл бұрын
+Madstaffy I use an acid bath. Here is a video that explains. Thanks! kzbin.info/www/bejne/pqfTlaNqj6eYb5Y
@Killer1259227 жыл бұрын
Hey, Skyler! So I've been making coin rings for a little while now (just out of the normal clad quarters) and I want to try a silver quarter soon. Before I attempt to make a silver ring though, do you have any tips that might help?
@CoinRingsfromTheMint7 жыл бұрын
+Killer125922 Silver Washington quarters are really tough to get straight! But they are cheap so that is good. Just go slow and anneal often.
@Killer1259227 жыл бұрын
Okay, thank you for the tip, Skyler! You are marvelous! :)
@vincecirilo86669 жыл бұрын
Do you use an acid pickle when you quench?
@CoinRingsfromTheMint9 жыл бұрын
You can but I don't. I do that at the very end.
@michaelsmithson32375 жыл бұрын
@@CoinRingsfromTheMint What mixture do you use for your acid pickle? Great video BTW.
@KristianWiborg5 жыл бұрын
Austenitic steel is not magnetic. Not sure how many coins are made of steel though.
@hiseminencetheholymacdiarmada9 жыл бұрын
What about hardening? Or is it even necessary?
@CoinRingsfromTheMint9 жыл бұрын
I used to think it was necessary but it really isn't at all.
@alexandermishenberg84568 жыл бұрын
Sorry,just got all answers from your wideoThanks
@CoinRingsfromTheMint8 жыл бұрын
No worries :)
@perroblanco494 жыл бұрын
someone told me that annealing clad coins can be hazardous because of the fumes, I know is not the copper but maybe because of the nickel or a combination of both? do you know if that is true?
@CoinRingsfromTheMint4 жыл бұрын
No its not. The nickel has to be melted to release the fumes they are talking about. I researched it years ago but that is what I remember the result was.
@perroblanco494 жыл бұрын
@@CoinRingsfromTheMint thank you!!!
@bradmoberly61646 жыл бұрын
I must be a idiot . I made two wobbly Kennedy half's lol. The clad ones
@jamesakenhead88587 жыл бұрын
Nice overview
@CoinRingsfromTheMint7 жыл бұрын
+james akenhead Thanks!
@trendguruji29383 жыл бұрын
Annealing on stainless steel does it make it soft? I want to soft ss metal how to do can u pls explain
@CoinRingsfromTheMint3 жыл бұрын
Not sure. I don't work with stainless
@frankhatton3656 жыл бұрын
cheers man exalent info
@CoinRingsfromTheMint6 жыл бұрын
+Frank Hatton Thanks!
@stick3446 жыл бұрын
how do you avoid the oxidation ?pickle?
@CoinRingsfromTheMint6 жыл бұрын
Yes exactly! I use nature's touch citric pickle
@perroblanco494 жыл бұрын
can you use non silver quarter or halve dollar to make a ring?
@CoinRingsfromTheMint4 жыл бұрын
most certainly!
@danielyost96588 жыл бұрын
hello sir do you review coinmaking tools? thanks Daniel
@CoinRingsfromTheMint8 жыл бұрын
I do some of that
@Woody-7777 жыл бұрын
I love JESUS also. Well done. GOD BLESS you.
@CoinRingsfromTheMint7 жыл бұрын
+Woody Thanks!
@chrischris4205 жыл бұрын
Is there a certain time frame to start working the coin after annealing?
@CoinRingsfromTheMint5 жыл бұрын
No anytime works.
@chrischris4205 жыл бұрын
@@CoinRingsfromTheMint thank you
@larrykelley18187 жыл бұрын
What are you using to lay the coin on to anneal it
@CoinRingsfromTheMint7 жыл бұрын
+Larry Kelley It is just a fire brick
@josephcalvosa82723 жыл бұрын
They call the color you are looking for "straw" yellow.
@timberwormy5 жыл бұрын
Has anyone tried annealing with a heat gun? I’m doing coin ring making with a group of elementary kids and they don’t want me to use a torch in the school.
@CoinRingsfromTheMint5 жыл бұрын
You can usually get away with no annealing as long as you keep the cut edge nice and sanded.
@frankhatton3656 жыл бұрын
just a note about butane and propane from what you say butane should be good .1400 degrees give or take compared to propane 1995 degrees from an air torch . just something to think about when buying gas.
@CoinRingsfromTheMint6 жыл бұрын
+Frank Hatton Interesting info. Thanks!
@alexandermishenberg84568 жыл бұрын
Can you or have to heat coin before punching center holl?And one more question: can you use 1 ton arbor press with 9 pieces punch and die set or it's not enough? Thank you very much
@CoinRingsfromTheMint8 жыл бұрын
No I don't anneal them before I punch them but I don't think it would hurt. A one ton press should make it through. You might need a breaker bar to extend the handle to get more leverage though. Thanks! Skyler
@damiandemarsico3569 жыл бұрын
What brand torch is this?
@CoinRingsfromTheMint9 жыл бұрын
I can't remember and it is so covered with cement that I can't see on it. I got it at Lowes though. It is a self starting one.
@mycaptainsvlog9 жыл бұрын
This looks great, thankfully u dont live in the UK. In the UK its an offense to deface a UK coin or note and punishable by a prison sentence.
@CoinRingsfromTheMint9 жыл бұрын
ouch! I have heard that about Australia also. Too bad because I love the way half crowns and 2 shillings come out.
@mycaptainsvlog9 жыл бұрын
Coin Rings from The Mint - Change You Can Wear I paid money into my bank account one day and on one of the notes someone had drawn glasses and a moustache on the queen on one of the notes and i didnt notice. The guy at the bank was really shitty asking if i had done it.
@CoinRingsfromTheMint9 жыл бұрын
That's pretty funny!
@willanski43217 жыл бұрын
It's not illegal to make coin rings in the uk! It's illegal to alter a coin then attempt to use it as legal tender - hence your issue at the bank - but not to turn it into something else. There's lots of UK based coin ring makers who sell rings freely with no issue.
@kozz19639 жыл бұрын
the 64 kennedy is only 40% silver . 1963 and older is 90% silver
@CoinRingsfromTheMint9 жыл бұрын
Actually 1964 was, the last year for 90%. 1965-1970 are the 40% halves. You might be thinking about the last year for the Franklin halves?
@sirbuddysworth3 жыл бұрын
Informative but it hurts to see coins being intentionally destroyed to make something else... Your channel is just not for me sadly.