HOW TO CHANGE TIPM (ON 2013 DODGE RAM 3500)

[@marks8368]

Thks for the video. For all others, I would recommend first removing the old one and using an electrical contact cleaner suitable for electronics on both the wiring harnesses and the male connectors. Then use ignition spray on the leads into the connectors to remove any remaining moisture in them. Then add a bit of dialectric grease to each connector. It's about $10 in supplies, and if there are still issues, sure go ahead and replace it.....oh and don't be afraid to pressure wash the engine. It'll help keep the dust and dirt from getting into these types of parts. Also, spraying the engine bay with wax once cleaned at the wand wash helps protect the wiring and connections as much as your paint.

[@donaldjordan8832]

My lowbeam lights work sometimes. I am thinking I have a connection issue and cleaning and sealing the module is the first step. Has anyone found the one fuse that controls the headlights? My foglights and highbeams work fine. Thanks for the video

[@rogelioornelas5776]

What was the problem before you replace the fuse box?

[@Junkyardmethod]

One tip I'll give you....anytime you unplug something go ahead and squirt some dielectric grease on there to help with corrosion and also to keep the crud out of whatever connection you might be working on. It'll save ya next time you're into whatever it is you're working on :-). Keep up the good work!

[@davidrios9094]

True that.

[@arosswelding]

thanks for watching and thanks for the tip!

[@sergiocastanon3842]

Do you have to reprogram the tipm

[@fixitman8028]

Nice job. Simple and too the point

[@Grarder]

Thank you so much for sharing this! My 2014 2500 just lost it's mind today. Google seems to say that thing is faulty (and defective). It's nice to know it's such an easy swap for something that controls the whole truck. Much appreciated!

[@leo959]

Did you have to program the tipm? Like to match the VIN or year?

[@deant876]

I had the dealer replace my tipm and repair the harness under it. It had an airbag light on (that was not on before the repair). Took it back to them 3 times to fix that airbag light. I Googled it and pushed the fuse in and the light went out.

[@gabrielochoa4414]

Did you have batteries unplugged

[@jmlcolorado]

What were your symptoms that pointed you in the direction of the tipm?

[@normanrichards5143]

Did you not have to get it programmed to the truck

[@rkhanso]

What were the symptoms that made you replace the TIPM? Did the truck not crank? After removing the battery terminals, did it only run for 5 seconds before it shut off?

[@arosswelding]

My truck just died goin down the row one day. Figured out it had somethin to do with my fuel pump fuse.

[@rkhanso]

@@arosswelding Thanks for that info. My son's truck went into limp mode. Later wouldn't start at all. The dealer found a loose wire/connection at C120 (not sure what that connector is for, or where it's located). Fixed now.

[@vegaslogger72]

Look at you. Diesel mechanic in the making!

[@arosswelding]

lol not hardly.

[@billwilliams6338]

AUSTIN ROSS, what does the TIPM do to the cars modules? example what a TIPM does?

[@007.3l]

It is the (totally integrated power module) fuse box

[@lionelwashington8448]

Thank you! Did you cleaning the area or did you just snap and go? Also what happen for you to know that was that part that was needed. Again, thank U.

[@jeremiahpenner4261]

Thank you so much for this video. About to have to replace mine in my 2016 Ram 3500. Thank god it threw a code for it. I just want to ask if you unplugged all the batteries before you did undid the hot wire, and where did you order this?

[@1godwetrust1]

You forgot to disconnect the battery first. Always disconnect the battery and it wouldn’t matter post bolts that you took off the top of the fuse box touched anything. And you’re supposed to touch the terminals together if you’re trying to start it

[@TOXIC-jq3ry]

Horrible advice. Touching terminals together could fry the entire thing.

[@newedgefrank3257]

So no need for reprogram the new box right?

[@gabrielochoa4414]

What was the reason for changing the TIpm

[@stevenwelland9586]

Did you not have to have it reprogrammed because it came pre-programmed from the dealership? Like already coded for your VIN somehow?

[@jg5488]

Steve Welland do a reset. Put the key in the on position for 12 seconds and then turn it off and take off the key. Don’t actually turn on the car when you have it in the on position and that’s a reset and should read the new tipm

[@stevenwelland9586]

@@jg5488 I bought a used TIPM with identical part number. Going to install today... sure hope it works. Thanks for the tip will definitely try.

[@jomine16]

@@stevenwelland9586 i know its been 2 years but did the used TIPM work without dealer reprogramming?

[@brysonmurray866]

Would you happen to know what fuse runs for my front single lights ? I got a 15 with projection lights and they both don’t work ( orange lights )

[@Icebreaker9]

Was the truck not cranking up?

[@synysterrhodes7025]

what is your thoughts on lincoln sa300 and a miller pipe pro?

[@toddcianciulli921]

If my truck has a programmer and tune on it will I have to mess with that or is that in the separate ECM ssytem?

[@johnnyhotrod]

Nice walk through,thank you!

[@shoancoffee4734]

We’re did you order yours from ? Having trouble with my 17 single cab ?

[@gavinheffelfinger4127]

Maks tipm

[@70chgrdreams78]

What was the problem?

[@ebeatz1234]

Will this cause my power steering to act up? Cause it so hard to find a rack and pinions for my 2013 ram big horn and it cost a lot o money thousands

[@davidrios9094]

Alright it works. No more stranded out of fuel days.lol I wrecken you just added 1000hp to that Cummins lol. By the way were was Alvin thought I heard him for a minute there.

[@Tazyz]

Why did you have to change it

[@louisnemick317]

Thanks for the information and video.

[@arosswelding]

my pleasure. thanks for watching

[@rondoschiavoni8840]

u didnt have to reset it ?

[@tayninh69]

Very helpful, thank you for sharing.

[@TrentPietila]

I'm on my 3rd tipm. Getting irritated with Chrysler's shitty engineering 2013 ram mega cab 2500 bighorn 4x4 diesel

[@bonnielaurie7530]

Me to on #2 @ $600 a pop. This year has A lot of wiring issues

[@AtrainFX68]

How many now ?

[@wyattyates2549]

Thx Broseph🤘🏼

[@lb7144]

Thanks for the video, very detailed and informative. I have a 2016, with to troubles so far but I like to stay ahead of trouble. Thanks again

[@juanrosales2041]

Yes

[@philippedusseault8042]

Fusible alimente prise 12 volt remorque

[@gabewhisen3446]

Oh you got lucky it's the non programmable one

[@hectorcordova92]

It nide repro?

[@hectorcordova92]

I have a Laramie Hemi 2009, i change it and the check engine start to blink and shake the motor. I turn it off an on again. Fix it but 20sec later starter again to shake

[@shugatoast7844]

I would have cleaned my engine before replacing . As a matter of fact, I keep the engines clean in all of my vehicles. make it easier to see if you have a oil leak or whatever. if you live on a dusty road, you're screwed.😂

[@chestercopperpot1073]

Hopefully this does the trick for mine. Thanks for posting.

[@PAPATexas]

👍

[@americahernandez3078]

☺👍Awesome thanks!

[@Stanlekic]

What was the issue? I have a 2013 ram 3500 diesel 6.7. I'm told my tipm module needs to be cleaned due to corrosion. The problem I'm having is that the truck is putting itself in 4wd without me doing it. Message on cluster says 4wd not available and when I put my truck in park. And pass through reverse I hear a loud noise.? Thanks!!!

[@brandonellingboe7721]

I have my ac and heat fans that will blow then they will go out mid drive, Idk if it is a tipm issue or what, I changed the fuse for the blower motor so idk if I will need a tipm or a new blower moder? Any suggestions?