Weld On Bullet Hinges and the YesWelder The Agressor welding helmet

[@Beekeeper_of_All_Trades]

you are the only person on youtube who explains how bullet hinge is aligned

[@SchysCraftCo.]

Very cool hinges. Weld on. Fab on. Keep making. God bless.

[@ArtfullyRogue]

Thank you! Jared and same right back atcha my friend

[@Marcus_Woodard]

I love that you are open to suggestions in the comments and are open to things that you could have done better. Subscribed.

[@ArtfullyRogue]

Thanks Marcus, greatly appreciated

[@barryphilrush719]

Very Cool Video Doug , Haven't use the Plasma Cutter very Much , So Far I Like it's Functions !! , talk soon Barry and Marlene

[@ArtfullyRogue]

Thats good to hear. I also hear that YesWelder is working on a new Plasma cutter they plan to launch soon.

[@DanielPaprocki]

Thanks. This is what I was looking for 😊👍🏻

[@vpraggg]

Would love to see this installtion in an already pre-exsting frame thats already up..

[@ArtfullyRogue]

I was hoping to get a video together of the install however the client pulled the plug on the project due to HOA issues.

[@tjiacab3272]

Great skill and experience shown in thus fellow, good job. Working men like this produce great things with their hands. USA needs more skilled working men. Pass skills on to the younger generations. There are plenty of young men needing guidance and skills. Thanks for this video. Lessons learned right here on the cell phone.

[@ArtfullyRogue]

Thank you very for the kind words. I love sharing whatever I've learned along my journey. Hope it helps someone on theirs

[@katykayy]

If you can just “drop” the gate onto the hinges, then can’t someone just pick the gate up off of them too? How are these secure?

[@ArtfullyRogue]

You do have a point. I failed to mention that once the gate is installed, if security is an issue, weld an additional tab above on the hinges to prevent the gate being removed easily. In my case, our gate weighed about 300lbs and the homeowner wanted the option to remove the gate for future projects he had in mind.

[@kansascityshuffle8526]

Can you weld the two hinges with the posts opposing each other?

[@tariqaziz-nn9wd]

Very very very nice ❤❤❤❤❤❤❤❤❤❤❤

[@MiyamotoMusashi9]

I'm guessing to make a gate swing in and out they just need spacing ?

[@ArtfullyRogue]

The bullet hinges are great for that use as there is no built in stop on the hinge

[@The575Shop]

I'd recommend a test fit before welding. Also maybe a mention of welder settings and repeated weld sequence, since if not properly set/repeated, it'll pull the hinge out of alignment. Nice work with the jig👊

[@ArtfullyRogue]

Great point, thanks Al

[@ocAToccd]

Nice jig for holding the hinge! But I would weld the hollow part on the door so that no water can make its way in...

[@ArtfullyRogue]

Good point. I got into such a hurry to get these gate doors shipped out I completely overlooked that aspect

[@edstimator1]

the hinges that I bought have a ball bearing that drops into the hollow section and the pin rides on that ball bearng. It may be possible to try to slide three ball bearings into that hollow upside down cup while hanging a two hundred pound door but I will leave that to others to try.

[@ocAToccd]

@@edstimator1 that might need some (elbow) grease 😉

[@lwwelding8466]

I normally weld the pin end to the post to prevent water sitting inside

[@AerialLensVideo]

Thanks for the video -- SO HELPFUL, as always! Hey, I have that Yeswelder helmet (love it) and wondering if you have any clues on how to tighten it more than it allows out-of-the-box, so that it will stay up better when raised. No doubt you know exactly what I mean. I don't want to break it.

[@ArtfullyRogue]

I wrapped a thin layer of foam around the head band to make it a bit thicker and that seemed to help me

[@funonoldwheels7150]

I'll save you guys some time: He talks vaguely about the hinges for about 90 seconds, the rest is an infomercial.

[@vladimirrangelalonso9106]

Hello, what load rating do does hinges have?

[@joederue2392]

Those are a good product, but not for a place like Michigan where you have cold and hot weather. There is no adjustment if poles heve our move

[@ArtfullyRogue]

good point. Not something we deal with much here in Arizona

[@79366813arizona]

Good to see you use gas shielding.

[@ArtfullyRogue]

Right! It took me long enough to make the switch

[@Everythings_Adjustable]

Hey Doug, I always thought the 'pegs' went on the post and the 'holes' went on the door?

[@ArtfullyRogue]

Hmm good question. When I asked the manufactured they didn't say it mattered which one went where on the post or door.

[@Everythings_Adjustable]

@@ArtfullyRogue I think Farm gates and internal house doors (where they have this kind of hinge) here in the UK have the pins (facing up) on the post/wall, anyway I just thought I would ask what you thought 🛠️👍😊

[@ArtfullyRogue]

@@Everythings_Adjustable I saw another comment from someone and they had a good point. Keeping the pins up keeps the hole side from getting water in it when it rains. That point totally slipped my mind when I put them on.

[@Fab2Mc]

Super 👍👍👍

[@ArtfullyRogue]

Thank you 👍

[@MarkATrombley]

It seems like you only make short videos to wrap around product placement now. Are you ever going to go back to making videos just to make videos?

[@ArtfullyRogue]

As soon as I have knew build in the shop, most definitely. Right now we're making water features and doors and I've already done several videos in those.

[@boblalonde5164]

Spent more time pushing the welder's mask than he did the how to welding the hinge.

[@ArtfullyRogue]

Damn him and his welding helmet 😉 they're hinges, is there a part of the process that didn't make sense?