Assembling the JUKI DDL-8700 Step by Step

[@halimashillingi9283]

This has been the most helpful video I've ever watched thank you.

[@raquelirizarry5857]

What do you think about that sewing machine? I want get one but I don't decide yet. They are good quality?

[@morgannjay2401]

Thanks so much! Would have not made it through the assembly without this video!!!

[@ruthwilson7451]

I just bought a juki 8700 and I'm having trouble with the belt that seems to be too tight the flywheel is a bit too hard to bring towards you. How do you loosen the belt?

[@ronlilly3285]

But you never told us how to time the machine. Do I lower it down until I see the 4th line or 3rd line , where is exactly is the place you want the needle bar before you tighten the screw back up?

[@simonasamaru6055]

Avete uno anche per la Juki DDL100?

[@saidulshikder7940]

Nice video 👍👍👌👌

[@mat-yy5uu]

I have a question, regarding a long spring inside the head of ddl 8700 machine. I bought the machine in surplus store and i discovevered that long spring already broken at one end and the other end can be found fixed at the back part of the machine, inside. Can you please tell me what is it used for? My machine has no tension release when i use the knee lifter. Thanks in advance. God bless.

[@CutSew]

I think thats a tension spring.

[@dilankengmo301]

❤ c'est très bien

[@moziburmozibur7226]

how much Bangladesh price

[@patriciamirgorod313]

Does the plate of the bobbin slide easily to remove, or it is meant to be slide with machine tilted?

[@CutSew]

on the 8700, it should slide out without being tilted

[@tdodo3026]

Hi. Thanks for the video. I have a question please. There are two 1/2 half circle rubber with some dimples on them (time frame stamp is 4:33-4:45). Do you know what they are for? I don’t see you use them. Thanks.

[@CutSew]

Yeah, those go under the rubber bumpers that get nailed into the table. You may want to check out our more in depth video on how-to assemble the DDL-8700

[@CutSew]

Also, those are really just shims in case the table top got milled out a little deep. They don't always get used.

[@sahidachowdhury7018]

Line up screw to flat area I don't where the screw

[@fefemtshokotsha3013]

Thanks for the video.Can you please advise?my industrial sewing machine drive belt is making noise when I sew. How can I sort this?

[@CutSew]

So many possibilities...Have you tried tightening the belt by adjusting the motor mount?

[@fefemtshokotsha3013]

@@CutSew thank you for the reply.I will try that

[@fefemtshokotsha3013]

@@CutSew you won't believe what happened.As I did according to your instruction.I discovered a teaspoon on the drive belt.My daughter was playing past week around the machine.With her toys.

[@marrizd]

Thanks for sharing this very informative video.

[@omegaglover]

Do I add the entire bottle of oil? And do I have to let it run for a certain about of time before I use it for the first time?

[@CutSew]

Omega Glover fill the oil bath to a level between high and low. Before threading and sewing on the machine, run it at a higher speed to ensure that the oil is pumping up to the top. You should see oil splashing through the clear oil window on the top of the machine.

[@Symia722]

Every drill I use to screw the belt down didn’t work

[@goheldilip4711]

Price

[@CutSew]

www.cutsew.com/Juki-DDL8700--ASSEMBLY-REQUIRED--57500_p_7009.html

[@رياضروعة-م5ه]

شكرا

[@DrStephanieMillerWilliams]

Two questions...Are the holes in the table pre-drilled? I have a Sailrite Fabricator industrial machine that I am disassembling, would my Juki 8700 & 1181n (I bought both) fit in the Sailrite Fabricator table? Thank you! 😊

[@CutSew]

Hi Stephanie, Most of the holes in our table are predrilled. The threadstand hole must be drilled. As for the Sailrite table, I have no idea. Sailrite is a manufacturer and distributor of its' own brand. No body sells it but them, so you might want to reach out to their support.

[@DrStephanieMillerWilliams]

Cut Sew Thank you! 😊

[@lluviaysol3083]

Hellodesde Perú

[@nounou6749]

Good

[@CutSew]

Thanks

[@giadichduong1009]

I would like to buy a blindstich machine to do ham, you have it?

[@madhavpathi1281]

How much this

[@CutSew]

Fully assembled is currently priced at $750 before continental U.S. Shipping is applied.

[@sebastjansslavitis3898]

is this servo motor?

[@CutSew]

Sebastjans Slavitis, yes it is. A dial in servo motor.

[@kongalla.tirupati.jai.bala2969]

Rs

[@miridagama1177]

Quanto custa?

[@CutSew]

Depends. See DDL-8700 page www.cutsew.com/Juki-DDL8700-Single-Needle-Lockstitch-FULLY-ASSEMBLED-READY-TO-SEW

[@CutSew]

We made a much more involved, very detailed, DDL-8700 Assembly video so you won't miss a thing. Make sure to subscribe to our channel & check out the DIY Juki-DDL 8700 1 hour video here kzbin.info/www/bejne/roK3enyBg7d1h7M

[@subowosubowo7112]

Bajed berapa di indo Mr.

[@desmondjairam514]

Didn't show how much oil you use how to put on and of button

[@CutSew]

You might want to watch the extended version of this video on our channel kzbin.info/www/bejne/roK3enyBg7d1h7M

[@kongalla.tirupati.jai.bala2969]

Good.ra

[@sawaireniwal4714]

Hello

[@abouzarmajidi4195]

Merhaba

[@saidulshikder7940]

Hi brother 👋 Juki mol 254 ,, video,, more ,,

[@jaybharat4738]

Havmac praec

[@mohammedalibrilliant9337]

Rs India n

[@tasawariqbal6745]

Pakistan Rs

[@tannerboy92]

who thought this annoying ringing alarm sound was a good idea?

[@CutSew]

that would be the founder who had that PA installed back in the 70's. I wish it wasn't there.

[@husainvarishhusainvarish9494]

Singh kitne Ki Hai Jo set Karte Hain video mein kitne ki machine Hamen8655461904

[@goheldilip4711]

Price

[@CutSew]

Current sale for unassembled - $575.00 plus shipping in the contiguous US.