One Shot Zero - ATN X-Sight 4K Manual - How To Guide

[@nokiot9]

I gotta say I’m completely blown away with this scope. Came in the mail today and it’s really well made and is mostly metal and had good brightness I just love it if it actually lasts.

[@farmerwoman5891]

Did you get it to zero? I'd be happy with that.

[@nokiot9]

Farmer Woman yeah. Once you get the hang of it it’s great. The auto zero works very well as long as you know your bullet specs and you’ve ranged the target with the ABL

[@edwardenglish1519]

It's been 2 years now, how is the battery holding up?

[@nokiot9]

@@edwardenglish1519 idk. Lemme go turn it on lol. I haven used it in months.

[@nokiot9]

@@edwardenglish1519 it’s fine. I haven’t plugged it in in exactly 9 months and it’s still almost fully juiced. But I’ve only fully depleted the battery maybe 10 times? At the most

[@SanDragoon]

Hi! Done on mine , zeroing OK with 5 bullet 50 to 200 yards Amazing . Love ATN

[@dustinmeier9753]

100 yards only took three rounds. Bore sighted scope before the first to get it on paper. Adjusted reticle to point of impact per the video. Second shot was dead on. Third shot was to prove that second shot wasn’t a fluke. Amazing.

[@travisrobichaux6628]

How do you see your initial bullet hole

[@maximusplayzz7156]

@@travisrobichaux6628tart of at 50 yards then move further out

[@angelisone]

Will the scope screen clearly viewable at 1 or 1/2 mile? Zero Range (5:22) goes up to 1/2 /or 1 mile (1760 yards or 1609 meters)? What brand, type, model, voltage are the *battery & user replaceable (not going to drop $200 to send it in)? * No fool is going to send it in just for a dead battery. Unless you have a full life time battery replacement. I and many that are going to buy or use scope like this know how to take apart guns. So DIY is must on battery.

[@bernardsbbq]

Got my new silencer today and used One Shot Zero on the scope, super easy!

[@tejeda7324]

Silencer is for liberals.. its called a Suppressor

[@ehsanebrahimzadeh8765]

I zero my scope at 30 yards, it works perfect for that range but when I go to 100 yards it's all messed up. whats the solution? Thanks

[@behrozejamaldini3561]

I love ATN

[@nealmcbaggins127]

Yeah... thanks... how are you moving the cross hair? I'm only asking because THATS WHAT I NEED TO DO

[@Richard5873]

I firing down hill do you have to judge up/down firing or does scope do it for you ?

[@daveyJ213]

Hello. I think I heard you say adjustments, i.e., data input, can be made from your iPhone or iPad? Could not find that video on your channel. Is there software available that can Bluetooth your phone and scope together? Inputting data on a separate device would be much less "clunky" I think and reduce wear and tear on the scope. Thanks for posting.

[@TMFShooting]

Great Video 💯 Thank you 💥💥💥💥💥💥💥💥💥💥💥💥💥💥

[@chipdavis1]

It would be nice if the scope took a picture when the rifle is fired, and you could adjust the red crosshairs to the bullet hole in the picture. Not try to hold the white crosshairs on the bullseye as you adjust the red crosshairs to the bullet strike. You can never hold it perfectly steady while adjusting, and you may not have been exactly on the bullseye when you pulled the trigger.

[@kimnord2737]

Night vision is awesome.

[@johnabel9744]

When I go to the bullet hole of my first shot and zero my cross hair doesn't come back to the center of the sight it stays we're I set it at what am I doing wrong😂

[@AtncorpOptics]

Your not doing anything wrong. The cross hairs wont be in the center unless your initial shot was in the center. If you do zoom in the crosshairs will be in the center.

[@johnabel9744]

@@AtncorpOptics so I'm still hitting dead center even when I zoom in. Then I'm good too go. Thank you I like the sight sestem form atn. Great at night. 👍

[@farmerwoman5891]

I'm sure this was a great video, but can't hear you! I'm not the only one with this trouble! That quick start manual, I'd pay extra for readable size print. Many calls to your customer service before actually speaking to someone, no help. For this price I'd like print I can read or video I can hear. Is that to much to ask?

[@AtncorpOptics]

Sorry about that. Here is a link to an electronic manual where you can even download a PDF and enlarge it manual.atncorp.com/x-sight-4k/

[@hayman41350]

@@AtncorpOptics Shouldn't have to do that!! I have basically said the same thing many times to other videos!! Can't understand or hear your presenter!!

[@bpizzuti]

Got one of your scopes not too long ago and just headed over to the KZbin channel… Great scope, reading the manual wasn’t hard at all. I went left to right stringing words together to form sentences- it worked like reading does. Videos here the chap could be louder, but nuts nothing to complain about IMO. Good stuff @ATN Corp.

[@BlackKettleRanch]

Where are your direction videos from the time of unboxing?

[@akaiphone]

does the ballistic calculator have to be off when zeroing? i try to zero mine today and had a hell of a time. it is almost impossible to zero at 100 yards because i cant see the impact hole

[@AtncorpOptics]

Yes you need to have the BC turned off

[@gregg9448]

Do you have to create a profile to zero it? I’ve been trying to zero mine for 2 days now with no luck. I’m not creating a profile but just clicking on the zero reticle.

[@dronetv6857]

If I will zero my ABL I need also to do this zeroing ??

[@baraj062]

which atn riflescope is suitable for both day and night hog hunting

[@baraj062]

@x X domuz avında hangi model alalım

[@baraj062]

Bu dürbün domuz avında ayışığı olduğu zaman kaç metreye kadar domuzu gösterir

[@baraj062]

Bu dürbün domuz avında gece kaç metreye kadar domuzu gösterir teşekkürler

[@theexisting1197]

Excellent.

[@erniehebert8828]

Having trouble to get my phone and scope to pair

[@onlysabsona1nanuashvili181]

That mine skope dont show me second kross and who can i hepl?

[@hectorblanco9423]

Is the one shot zero set up necessary if I am using the ABL paired to the scope?

[@AtncorpOptics]

Yes you need to zero the scope using the One Shot Zero.

[@hectorblanco9423]

@@AtncorpOptics thanks

[@farmerwoman5891]

where is the key pad you said to use in order to move the cross hairs

[@AtncorpOptics]

The key pad are the external buttons that operate the scope.

[@farmerwoman5891]

@@AtncorpOptics key word was (where) not what!

[@boskoromanic7425]

Does balistic caculator data exist for air rifle calibers for exemple .177 caliber?

[@AtncorpOptics]

Yes you are able to input BC data for air rifle calibers.

[@nunya6874]

Reaching out fellas bcause I need a solution to an ATN X-sight issue and unfortunately can’t call the company since it’s a weekend. Have a coyote trip planned for tmorrow evening. Went to mount and sight in xsight 5-20 on my .457 challenger bullpup and @50yds I was off paper by a good bit. Using the one shot zero I was able to move cursor and reticle like you are supposed to but now my reticle is basically stuck on the far left side of the screen. Any ideas on how to fix this issue?

[@lazykbarranchoutdoors]

Mine moves the white cross hairs instead of the red… unless the guys moving the gun as he is using the buttons

[@kaceyweaver8073]

Idk if this has been asked or not, it can you zero the scope while in Night vision mode? Like if I wanted to check and fine tune my zero at night before I go out for a night hunt?

[@AtncorpOptics]

Yes you can.

[@w.t.pstandforyourlife.5639]

How did you show it on your laptop screen like that

[@AtncorpOptics]

This is an internal program. Sorry, you will not be able to do that.

[@tacticalbacon8064]

@@AtncorpOptics can you release this internal program so that we can use it because the one thing i hate about the app is that you cannot see the HUD which for my spotter would be very valuable information wasn't

[@austinvass4308]

I recently did a firmware update and reset to factory settings. Do I need to zero my scope again or will it stay after a factory reset???

[@jeffstrains4014]

Does this scope react to targets differently? Today I was trying to zero on a paper target would not zero (100 yards), I finally do away with the paper target fire at the gong its dead on! tweak a little there, then go to my hunting stand shoot the gong again boom. This shot was almost 800ft I am concerned with the mount might switch to a QD. I am not sure if the ballistic calculator is messing with me or not. Thanks

[@AtncorpOptics]

No, the scope would not react to targets differently. The scope has a digital zero that consists of X & Y coordinates. There is no way for that to lose zero. If you are having issues then definitely check your mount and make sure everything is tight.

[@drewt.4353]

Any scooe worth their glass can do a 1 shot zer0. Note how it says follow up shots may be needed ...

[@boskoromanic7425]

Ok but what is the point of range finder if reticle is not moa or mil dot spec. How does it work automaticly trough balistic caculator to adjust shot point???

[@AtncorpOptics]

The ballistics calculator will adjust the reticle to the new POI depending on the distance ranged.

[@boskoromanic7425]

@@AtncorpOptics tnx for the reply

[@boskoromanic7425]

Does balistic caculator data exist for air rifle calibers for exemple .177 caliber?

[@AtncorpOptics]

@@boskoromanic7425 Yes you can input the air rifle calibers into the BC.

[@boskoromanic7425]

@@AtncorpOptics nice! tnx.

[@TheBig5Hunter]

Question, what is the maximum adjustment for such a scope? Also would having the correct sight height help you adjust accordingly, given that the adjustment is finite and you may run out of adjustment if the scope is higher than the default 1.5 inches.

[@jeffstrains4014]

I know this question is old but for my regular day scopes the lower the better, also I do not us any mounts with built in MOA for hunting. I try and keep my shot as flat as I can so I am not only accurate at a certain distance.

[@outdooraddictionwv5299]

when I push the direction buttons to move the reticle towards the impact it controls the white reticle. how are you moving the red one

[@nokiot9]

The red one follows the white one after you set the white one. You lock it in the vise and keep move the white one to the impact spot. Then the red will auto adjust once you click the middle button.

[@bennyverano8397]

I had tried so many times, following the simple instruction. The shot nowhere to be found on 3’x4’ target at 60 yards. I bore sight and it was way low to the crosshair. I tried zero it the way it was instructed, It went the other way (opposite). I spend a lot of bullet trying to find out, And it was confirmed, the adjustment was going further more to the first appeared shot on the target. Help me please.

[@AtncorpOptics]

Sir, you can give a call to our CS team, they can help troubleshoot this with you.

[@michaelcarolsanchez9000]

my reticle doesn't scroll down after first shot fired to save and exit. frustrating

[@AtncorpOptics]

Please give our CS team a call. They can help troubleshoot the issue with you.

[@sergeantmao8017]

Hi I have a ? I had zero and start everything fresh on 5x20 4K pro. I was doing fine on point in the bullseyes. So when I turn it off and turn it back on why my zero shift point of aim too the left 3 inch. I had recently updated all firmware now it’s doing this too me. Have any clue why it’s doing that. I try too zero it again and repeat the same process again still the same result when I turn it off and back on. It’s frustrating.

[@dguadian]

have you found the solution? I might have the same issue.

[@sergeantmao8017]

Daniel Guadian I still couldn’t get it right. It’s still shift my POI 3inch too the left or right. I had updated the firmware again still the same process. Even though I zero it and In put my info still POI shift. I start off 15 yards and 25 yards just too see the result and still an issues. Then I try 50 yards it’s some one accurate and a couple days later it change again. There gotta be a better solution for it for what I spend. If you find out too have it set and stone let me know please I’m welling too learn from other.

[@dguadian]

Sergeant Mao don’t give up on it yet. A lot of bad reviews out there but definitely plenty of more good ones. We will figure it out.

[@jeffstrains4014]

@@dguadian Trying to get mine zeroed in today I discover it reacts to metal better then paper. Not sure there

[@toddjenest3212]

What if I want to do a 36 yard zero on a 25 yard range?

[@Dynamo55b]

SMH… Seriously dude…

[@rodinapatockova2]

Please, what i have to do when the sreen is Frozen? I know when i reset It, Its ok but after maybe 2 minutes It happens again. It happend me many times and i dont know why.

[@AtncorpOptics]

Follow the steps in this tutorial to fix the issue kzbin.info/www/bejne/h6HVmHx6qs-WiaM

[@rodinapatockova2]

@@AtncorpOptics Thanks mate 👍

[@Maskara24]

Hello, can i ask how do you capture this menu view exactly please @atnteam

[@AtncorpOptics]

This is only for internal use. You cant capture this menu.

[@Dynamo55b]

Thank you for your efforts…

[@mikestone9129]

What do you do if your adjustment doesn't move enough to zero?

[@rubenramirez2303]

My do the same thing, I need a little to go down to zero!

[@toddjenest3212]

Did you start with bore-sighting?

[@pappydanny58]

Why does mine the opposite on the cross hairs? I have to use the white to move to the impact other wise is moved off twist as much

[@AtncorpOptics]

You should keep the white reticle in the same position after firing the round. Then you move the red reticle to the bullet hole.

[@pappydanny58]

ATN Corp. I tried that but it moves the point of impact that much farther away but I had the zoomed all the way. Does that make a difference???

[@AtncorpOptics]

@@pappydanny58 Please give a call to our CS team at 800-910-2862. They will help troubleshoot the issue with you.

[@AO-ip6yx]

Push the ok "buhin'"

[@marceloalonso888]

I’m having issues as well I have been trying to zero out but I’m still off by a couple inches and having a hard time locating the bullet hole to trace

[@keithsams4301]

Be nice if you guys could turn up the volume a little...kinda hard to hear these videos

[@Hunterworks]

Why can't you turn your own volume up?

[@keithsams4301]

@@Hunterworks I have it all the way up...just have a hard time hearing you..sorry

[@Hunterworks]

@@keithsams4301 it is loud as heck on my end when I turn volume up, get better speakers.

[@farmerwoman5891]

@@Hunterworks I think maybe cheaper if they speak up. But hey, matches their quick start manual print to small to read

[@farmerwoman5891]

@@keithsams4301 same here, tried on different computers, same thing

[@leeknudsen940]

Five guys, five similar rifles, all shooting the same caliber, all identical scopes, all from the same dealer. 3 of the 5 had to be sent back day one at the range. After all replacements were received and all five were confirmed as "working", only 2 of us (oddly 2 that had to get a replacement) could get it to zero. All of us followed the instructions verbatim, and identically. Started this whole process almost 2 weeks before our hunt. All said and done, we were still jacking around with these things the day before we left. In ~theory~ this is a great product. Pheromonal idea, smart advertising, excellent cosmetic design. BUT for nearly a thousand dollar scope, yall need to fire whoever is in charge of your QC operations off the production line, reexam the materials used, perhaps the skill level of your factory workers, something. AT LEAST ONE IN FIVE, in the hands of fairly tech savvy hunters, should have worked without issue.

[@MrMadeinthe80s]

Having the same issue with my Gen5 today. After 16 rounds it still won't hold zero. After zooming in or out you can see the reticle shifts away from zero. Doesn't seem to matter what I do I can't get it to function properly.

[@joshtran1483]

Mine isn’t holding zero at different zoom ranges, useless

[@ddunkers98]

Mines doing the exact same

[@Khannah69]

I have a problem with adjusting X / Y values. Everytime I try it jumps 0-4-8-12. For example, I can't set Y 13 or X 9. Is there anything I need to know?

[@AtncorpOptics]

You may be adjusting when the scope is zoomed in. Try adjusting the zoom to base magnification and then moving your X & Y values.

[@autocrcdrift5560]

Qual o dispositivo que o atirador tem no pulso para monitorização das condições climáticas?

[@JayRuperRoe]

Why don't you show "ON The Scope" what your doing. Not just on the screen!!!

[@keshkakotera8972]

Before all this digital stuff, back in the ole' days. One would normally zero your scope at 100 yards. Then knowing your bullet trajectory, adjust your aim point for the distance you're shooting. Not much is mentioned here or in the manual about doing this at a specific range. Why not? If I don't "tell" the x-sight how far away the target is, I don't see how one shot zero could be accurate.

[@matiasucles2524]

Hola es legal utilizarlo dedia,,, supuesto no lleba el ir incorporado gracias es pero su respuesta

[@gavinfitton7864]

It’s more than one of mine didn’t even hit the target

[@victordenoman3808]

Pls b adviced that somebody in Phillipines is scamming buyers offering your product but delivering useless product,the name is kettlen-1

[@johnegan7622]

Hi, I see in your profile settings you record your sight as being 1.5in high. Is that measurement from the top of the rifle barrel to the bottom of the scope? I have a Howa 1500 with picatinny base plates. Using the mounts that came with the Atn 4k pro, I measure from centre of rifle bore to centre of scope as 2.48in (using calipers). I want to set up a point-blank zero on my rifle of 200metres. Am I correct to set up my rifle zero at 1.5in above the bullseye at 100metres using 55gr ammo?

[@AtncorpOptics]

To correctly set sight height you need to measure from center of the bore to center of the scope.

[@darrylhamill5039]

Where can I buy one in new Zealand can it work on older air guns

[@feniz.50]

Atn come to Europe I need buy my scope 😭

[@davidstorton910]

They have I bought mine in the UK, try optics warehouse

[@baraj062]

Bu dürbün domuz avında gece kaç metreye kadar domuzu gösterir

[@marcelorrodriguez566]

I just bought a atn pro 4K and when to go zero it in for the first time and I have it on a 300 black out and I tried to shoot my first shot to do the zero calibration and it keep missing the 24”x36” target at 100 yards and I went through 20 rounds without hitting the target once. Is there something in my profile not set up right? I put the bullet gr and muzzle velocity but one thing i didn’t do it put in the sight height and I also didn’t update it once it got it out of the box and mounted on my gun. So what could be my problem?

[@AtncorpOptics]

When you zero the scope make sure you have the ballistic calculator off. The reason you could be way off paper at 100 yards is that the scope is not exactly at the center. may be off by a little and you are missing at 100. Try to zero at 50 yards then work your way to 100.

[@travisrobichaux6628]

Or atn your shit is garbage. Because the only time I can see a bullet hole is at 25 when I move to 100 I have no clue where my shots are. You can't see them with your crappy ass scope so there is no way to sight it in

[@travisrobichaux6628]

​@@AtncorpOptics Fuck you atn please give me 2 dollars back and I ll give you this piece of shit scope

[@travisrobichaux6628]

​@@AtncorpOptics Well no shit you dumb fucks

[@pigpunishers4550]

Low audio

[@AuthenticZack]

wow you sound amped up bro

[@oldiowan]

OLD & DISABLED - I just got the ATN X-SIGHT 4K, 3-14 night scope and STILL I am having a DIFFICULT time learning how to input and edit PROFILES - I called ATN tech support and confirmed that the instructions I need do NOT EXIST in writing!!!!!!!!!! I would like to work with an expert and create these instructions in a PDF that would be free for every one, which I have the ability to do - Anyone willing and wanting to work with me on this would be greatly appreciated!!

[@dguadian]

ill work with you - what needs done. i still cant zero my gun.

[@farmerwoman5891]

I got the same reply from customer support. Had me go to the web site. Got the neighbor kid to down load then print out the manual in print I could actually read. However I'd need to plug in to a I pad in order to move the cross hair for zero. I don't own an I pad.

[@farmerwoman5891]

@@dguadian Did you get yours sighted in? I'm in the same boat.

[@oldiowan]

I FINALLY got it figured out BUT IMHO even I could produce a MUCH better manual - Too bad most of the SUPPORT ends about 2 weeks after I finally got it back as it needed repair before I could even use it!!!!!!!!!!!!!!!!!!!!!!!!!!!! MAYBE.....It's just me?!?!?

[@toddjenest3212]

I found it easier to edit the profiles from my iPad. In the scope, create as many profiles as you can. Then, log into the app on your phone or tablet. You will be able edit the profile names and stats for each round in each profile WAY easier then through the scope.

[@franciscomaia9784]

Muda para português

[@bradjon7231]

Your volume is way to low!

[@mustlovedogs272]

I must be hard at hearing.

[@travisrobichaux6628]

This doesn't explain at 100

[@levipond5649]

The audio in this video is terrible

[@maksparamokhin6761]

One Shot Zero without real shot? Greed bastards :(

[@rettamezera8772]

What key pad and scroll wheel??