How to quickly determine if the no sound issue of your Onkyo receiver is caused by the famously bad DSP chip.
Пікірлер: 783
@SolidSleds Жыл бұрын
I bought an Onkyo used a few years ago and it had no sound when I connected. I saw your video and decided to try your trick for the heck of it. IT WORKED!!!!! I don't care if it is a temporary fix, your video resurrected this boat anchor and made my purchase worth it. Thank you so much.
@stephaniemanchester-chermo3840 Жыл бұрын
Our family business is the rebuilding and/or repairing of 1960’s to 2000’s Harley Davidson V-twin engines and after decades of dealing with the general public I’ve learned that leveling with people and simplifying things as much as possible when explaining a technical issue is greatly appreciated. Anyone that would give this a “thumbs down” must not understand the point of many of these videos? Anyway, great video, thanks for the information. 😊
@johnq.public3302 Жыл бұрын
The moment where a $40 paperweight you shouldn't have bought from goodwill starts working! HOLY CRUD! Bought an HT-180 and discovered it had this exact problem. Grabbed a bulb just like you had and applied it to the chip for about 5 mins and BAM! The dumb thing works! Unreal. Great video!
@stb3265 Жыл бұрын
Lol. Me too. I got a 708 for $10 at a thrift store. I used a butane lighter to heat the chip to 380F (very carefully and using a temp gun to keep an eye on the temps). Works perfectly. If I get 3y out of it, I will be happy. If not, it was $10.
@richardhalliday1595 жыл бұрын
Occasionally the BGA solder pads do not 100% flow in the cct. board manufacture and the odd ball may end up just having a ‘touch’ contact that may work and not show a fault until later. In and amongst my life as an electronic technician before retiring from the game, I was involved in a R&D and debugging role at a major digital satellite and cable receiver manufacturer and occasionally came across this problem, giving the chip a little tickle with a fine nozzle on a hot air gun sometimes cured the problem, even using an expensive professional rework station replacing. BGA (ball grid array) is a nightmare, you cannot guarantee that additional heat applied after original board flow will not damage the internal tracking of a multilayered circuit board, as you say, the bit of heat with a bit of luck will keep your board running a while but you end up repairing it as a freebie!! Keep your little films coming,I’m sure they help a lot of people
@jsar48382 жыл бұрын
Thank you once again! I did this method to my onkyo tx-nr414 half a year ago. Few days ago I lost the audio and I did this trick again. Enjoying good music again! Thank you:)
@Fifury1615 жыл бұрын
Nice customer service - it's always good to prove out the fault and provide a cost of a proper repair! Thanks for sharing.
@runepedersenDK5 жыл бұрын
Finally! Been watching this very interesting channel for a long time, been waiting for this. Got two of those recievers, a TX-NR579 (driving two Klipsch RB 51 used as computerspeakers), and a TX-NR 808 as main HiFi unit. Both are approx 8 years old.and they always had a lot of cooling space arround them, and were never abused. The 579 failed in 2016 and was put in a closet, and after I realized that there was an extended warranty, I send it in (2017/2018) and it was repaired (new HDMI board). Still working fine. The 808 never failed. Thanks for a very cool channel!
@pdxway3 жыл бұрын
Thank you! Thanks to your video, I decided to purchase a 300w heat gun from Amazon. Just two hours ago, I tried heat gun about 3" away for about 2 minutes. I tried power on twice and both times my 808 would have sound right away from cold power on. Will see how long this lasts.
@pierreevensmeneide70028 күн бұрын
It works for me. I used an heatgun at maximum power for a minute on the DSP chip on my Onkyo TX-SR313. Thank you for the tip.
@thiyagarajandayalan7344 жыл бұрын
This trick worked for me. I am from Chennai India. Great and thanks to you.
@nancyfansher47915 жыл бұрын
I have been through so many Onkyo's. The last great trouble free one I owned was a TX NR901. Used daily until I just had to have HDMI. Even then the 901 was used in a garage setup for another 10 years with zeo problems. When I went HDMI, I decided to go with the TX SR805. I was so impressed with it that I bought a TX NR905 to get Ethernet input and moved the 805 to my front room setup. well, not soon after that the 805 video and sound. Tried to get it repaired, but Onkyo wouldn't honor. At that time I bought a TX NR807 on clearance to replace it. Not soon after the 905 lost sound. I was able to locate a TX NR5007 on closeout and picked it up. Again, Onkyo refused to fix the 905, so on the shelf it went. You know where this is going, not soon after the 807 failed. Lost Video, Ethernet and audio. I tried the 5008, but started having issues out of the gate with it and was able to return it. At this point I was done with Onkyo and switched to Denon. Of coarse the 5007 failed too, so I trashed the 805, and the 905, 807 and 5007 sat on the basement shelf. Years later Onkyo decided one time only to repair these units, but guess which model was left out? The 905 which I found to sound the best for Audio out of all of them. I sent in the 807 and 5007. The 807 is still sitting on the shelf since getting it back and I put the 5007 in my basement and it was still acting wonky when I got it back, but Onkyo refused to fix. None of the input buttons respond correctly and when you try to power down it will either turn zones 2 and 3 on or put it in pure power mode. after about 10 pushes it might finally turn off, but not before clearing all of your settings as if you did a factory reset. I would love to get the 905 back up and running and the 5007 working properly, but no one will tough them. :(
@12voltvids5 жыл бұрын
I am currently using a 605 which was given to me last year. When my RC370 started acting up again after 3 years (after the light bulb fix) I put in the older 605 and use it just for TV sound. It doesn't work properly with analog inputs, as it won't convert them to HDMI like the 370 did so my VCR and Laserdisk is useless as they are remote mounted and not connected directly to the TV. In my setup all my equipment is in a separate closet, about 30 feet from the TV, so all switching needs to be done remotely. Since I still have analog sources, getting a new modern receiver that only has HDMI is not an option. I have resorted to plugging my VCR and Laserdisk player into an MTS stereo modulator and sending the video and audio over RF to the TV, and then the sound back to the receiver. Not an ideal setup, but at least it allows me to view VHS, Beta and Laserdisk analog sources. I don't use these much these days anyway.
@materialsguy20025 жыл бұрын
Onkyo has always had great features (10.2 sound before anyone else, etc) but I was always concerned about reliability. I ended up with a Yamaha and I love it. Thanks for the video and a cool (hot) diagnosis!
@gplusgplus22863 жыл бұрын
My basic year 2000 Yamaha still works. Ive had it on my TV and connected HTPC and never turn it off, right now its playing this video.
@tacofortgens3471 Жыл бұрын
Yamaha isnt like they used to be, build the same way as Onkyo's Denons and Hamron Kardons. Cheap
@donaldfilbert48325 жыл бұрын
How could anyone give you a thumbs down for such an innovative; simple; and totally conclusive trouble shooting test? I thought that was amazing !! I do wonder where you might find programmed DSP chip replacements for any of these recent intelligent receivers ??
@kindanyume5 жыл бұрын
idiot elieteists snob fuktards that think anythingnotdone with a fancy station that costs as much as a car just can never be good etc etc same sort od morons that buy XTZ brand thinking its cook cause they paid $$$ meanwhile reality is the exact same thing is sold under abc logo at 1/ the price and they would look down on those buting abc brnd once again there is no lack of stupidity in the universe!
@deangale4496 Жыл бұрын
And why wouldn't Texas instruments re issue one that worked
@GameInterest5 жыл бұрын
I really dig the no frills approach you do. You just say what you're going to do and you do it. Also, your lighting is pretty good.
@Starphot5 жыл бұрын
Nice video. I've been out of repairing receivers and other things since 2001 when I was laid off and then ill after 30 years in the business. This looks more like a computer motherboard than an analog receiver to me! When I got laid off, these SMD micros were slowly populating the boards of the newer models. I've seen a lot of thermal problems on the older units of various descriptions like the one described in your video.
@makeminefreedom5 жыл бұрын
Great tip. I never thought of doing this before. It does makes sense that continuous heating and cooling would eventually crack a solder joint. Thanks for sharing.
@12voltvids5 жыл бұрын
It is either a cracked solder joint or a cracked silicon die inside the chip.
@vdochev Жыл бұрын
It's the interposer inside the chip. If you heat it up things expand and make contact again. The bad thing is things also shrink... So, as the owner of the video said, it's not a proper repair, you need to replace the chip with a good one. And then probably provide good ventilation when using it.
@GTAmelody9 ай бұрын
@@vdochev I see that non-existent cooling on DSP's is the main reason of their faults?! Thank You both for your knowledge!
@shelterstation4 жыл бұрын
Many thanks. Worked for me on my TX-NR609 just now. 3-4 minutes heating with a 50W 240v Halogen Bulb touching the TI Chip. If it doesn't last then I will try 6 minutes. Started to smell a but burnt dusty.
@williamchow16245 жыл бұрын
Why care about the people who give you thumbs down, they are idiots. The goals is to diagnose the problem and fix it. Just because it is unconventional makes it better and creative.
@therealjammit5 жыл бұрын
If it's stupid and works, then it's not stupid.
@MichelLinschoten5 жыл бұрын
Sure .....just hack away duct tape can patch tons of stuff ....doesn't fix it.
@ThatTransistorGuy4 жыл бұрын
I gave a thumbs down simply because they said "onkyo garbage receiver" if it was a simple diagnose and repair, then why put that???
@jeffcotton5264 жыл бұрын
I gave a thumb down too because of his blanket statement about "Onkyo garbage receiver". The chip was/is garbage not the receiver. He continually makes generalizing statements about overall product quality in a lot of his videos. He should have clarified by stating: "junk Texas Instruments chip." Onkyo makes some excellent top-notch products, I used them for many years. ALL BRANDS at one time or another suffer from poor or bad component quality, whether it's Marantz, Acoustic Research... whatever.
@DrDroogkloot5 жыл бұрын
I have multiple onkyo’s now. A 508 fixed the output stage. Still working great. Fixed a 313, faulty standby relais. Sold it. Now using a 607 as main home audio unit. Had no display. Fixed it. Great unit. Other units. 706 hdmi board total failure 414 working but no video. Another 313, hdmi chip fried recently. 578 also kind of fixed. Still working on it. Next to the hdmi board chips running very hot. Also the amp itself runs very hot. This is also a reason to get the unit as cool as possible. Btw dave... get a hot air station.
@johntranquilli22433 жыл бұрын
I was skeptical, but I’m not lying, this totally worked.. baked the crap out of it and now it works again!
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@johntranquilli22433 жыл бұрын
@@vortexor1 , yup, don't want to jinx it, but going on a few months now!
@lxxfxx Жыл бұрын
This video helped me to identify the issue with my Onkyo TX-NL509 years later. Will try to find the parts and otherwise... Well so long Onkyo, I guess. Thanks OP!
@mcramp205 жыл бұрын
You helped a lot with my 709 before I paid Onkyo to fix mine I found that if you put the audio settings to DIRECT you can get the amp to come on in stereo.
@12voltvids5 жыл бұрын
Not mine. When it failed it was dead even in direct mode.
@spikester5 жыл бұрын
@@12voltvids I think the dead chip stops the protection relays from closing, so the audio is gone until that happens even in direct mode. I had an SR-707 repaired by Onkyo for free a couple years back that I bought in 2010, it worked fine since before selling it.
@BeefyMon5 жыл бұрын
My TX-RZ800 died a similar death (I will try this fix shortly), but the analog and toslink inputs still work perfectly (assuming the unit isn’t set in a mode that require the dsp chip to process the sound). Dolby 5.1 works fine, as does All-channel stereo, and so on. I ran my blu-Ray player’s HDMI directly to the TV, and used an optical cable to feed sound to the Onkyo. I lost the higher resolution audio and Atmos support, plus the ability to switch video sources... oh, and the onscreen menu... BUT, it got me by until I picked up a newer model at a decent price. Incidentally, I wasn’t aware of the RZ800 being prone to this issue, but it happened twice (the first time under warranty, the second time, not).
@kennethwallace43385 жыл бұрын
Blew out a JVC 87 year model monster. Took 12 speakers and one to short contact to fry it. It came on but no sound. Thing was in use 26 years. Gave it to guy next door when I moved, he probably got it to work had a number of units in his backyard garage. My other JVC still strong after 12 years but using only the speakers that came with it out the box. Nice video.
@mrcrazyjonpresents43124 жыл бұрын
I have TXNR609 which i bought nearly 2 years back From what i can gather i'm the second owner of it from brand new Having watched you vid i thought i would have a look at the famous HDMI board and the DSP chip as you pointed out and i was happy to see a little sticker on top of it saying NEW lol so i'm praying that this means someone once changed it All this means now is one day the HDMI board will probably fail next but seen as this amp has been around now 9 years i just hope it lasts till i can afford a new Dolby Atmos based amp one day lol Great vid
@skullgame2 жыл бұрын
Thanks so much! I've had an Onkyo receiver sitting in my extra room for several years waiting until I could justify costly repairs, and now I have a way to potentially isolate the issue without having to take it in to someone and get charged labor for troubleshooting. Can't wait to try your solution (and if I'm lucky get another 3 years out of the receiver).
@SolidSleds Жыл бұрын
If you haven't tried it, do it. I used my heat gun from a solder station and it fixed my Onkyo that had been setting dormant for a few years.
@int531855 жыл бұрын
I glued a heatsink on mine 4 years ago and it is still working.
@saqibsami79675 жыл бұрын
Which compound did you use and size of heatsink?
@dom38275 жыл бұрын
@@saqibsami7967 i think any heatsink that is not too large will do the job.
@int531855 жыл бұрын
@@saqibsami7967 Arctic Silver compound. The heat sink I salvaged from an old tv circuit board roughly the size of the chip.
@CT-te3kb4 жыл бұрын
@Stephen Morton Needs to be a non conductive thermal compound to adhere the heat sink
@MrTopsoil9114 жыл бұрын
I used a mix of white toothpaste and dab vaseline. Working now 4yrs
@oledebess Жыл бұрын
great video, used a heat gun with nozzle to heat the dsp chip for 1 ½ min. and now sound is working, also the Network actually also work it was not responding before repair. Have added a small heat sink on top of dsp to improve, but thank you very much.
@CaillouLP5 жыл бұрын
Sad to see that these newer Onkyo receivers are apparently not reliable. They used to be a pretty big player when it comes to stereo amps. I have a A-9155 that I have not turned off in over 5 years and it still works fine.
@andrewstambaugh24011 ай бұрын
It was a common fault of the era, drive by government regulation forcing too rapid a transition to under-tested new solder. A whole bunch of computer parts had the same problem. Laptop gpu's were notorious due to running hot and exposing the flaw in as little as _1or2 years!_ imagine buying a new laptop and bluescreening with HW failure in less than 2 years. Also, note that the fault use in a TI chip, not onkyo. Several other companies had similar problems, but onkyo had more *because they put the best of the best new chips available in even their cheaper units.* Most other companies were cheaping out on features in sub-$800 units, so most of those weren't affected. Things like dolby only or dts only models vs onkyo with both and vertical sound and auto tuning mic and more hdmi inputs and... It's sad the heaps of laptops and other electronic went to the landfill so the gov could put on the image of "saving the environment."
@Travis1411233 жыл бұрын
Got one at the dump. You can bypass the HDMI board by (unit off) holding bd/dvd, press power and when display shows "hdmi :use" push power gain and it will toggle to "ignore", release bd/dvd. You just get basic audio inputs, no fancy AV. You'll have sound but no tone controls. Using Zone 2 you get tone controls.
@zandzak902 жыл бұрын
Let me guess. This trick does not work on the HT-R558....?
@matthewg78352 жыл бұрын
Doesn’t work on HT-R590
@arturcoelho88892 жыл бұрын
Dude It worked just now! Amazing man!!! Onkyo should build a Statue in your name!!! Thank you very very much!! best regards
@dumbfishtanks2 жыл бұрын
Also for those trying this and having no success, it'll only play sound in Direct mode, any other modes won't work
@intoflatlines Жыл бұрын
Thanks for this tip! Worked on my NR708. I just wanted the damn thing to power my speakers.
@FrozenHaxor5 жыл бұрын
Also from what I heard from fellow technicians, when Onkyo did the recall till october of 2018 where they fixed those for free, they used a board that dropped the DSP voltage rail from 3,3V down to 3V, most likely to lower the power that the chip needs to burn. Huge fail on behaf of Texas Instruments...
@toddnunley85915 жыл бұрын
Wow, just purchased a Onkyo TX-NR575 for Christmas last years. Had no idea they had these kind of failures. I was in the electronic service business myself started in the mid 80s but by the mid 90s I gave it up. Hard to make money since consumer electronics was getting so cheap. The cost of doing service kept going up, the return kept going down. Also I got was pretty tired of working my arse off only to make the shop owners rich. Got into office equipment after that and did pretty well.
@martinm9979 Жыл бұрын
onkyo did a recall few years back due to this issue . many ppl bitched about no sound video issue so onkyo caved in and did the recall. had my ht rc270 fixed for free. gowever all electronics mwde these days made like crap. cost 150$ these days in canada for diagnosis.
@MrChuckmason3 жыл бұрын
Great to find this after 2 different Onkyo receivers and 2k, I bought a Marantz.
@Evermoregreen234512 жыл бұрын
That’s magic. I didn’t know that you could fix chips with a light bulb. I know that you can fix soldering issues with a bulb or applying heat but not fixing broken chips. Amazing. Thanks for the insight.
@12voltvids2 жыл бұрын
The fault is bad solder under the chip.
@erikpnoman4 ай бұрын
Thank you so much for the information. I fixed my TX-NR616 using a heat gun. It ran for six more months. Stopped working again. Next receiver, Denon. See ya, Onkyo!
@sonotdown9985 жыл бұрын
My Onkyo gets so effing hot you’d think it would fix itself.
@dom38275 жыл бұрын
im glad i do not need an AV Reciever. I have a simple vintage AMP which barely gets near hand warm on the heatsink itself when i listen loud.
@kevinxero5 жыл бұрын
@@thefreestylefrEaK you could take a CPU fan and run it USB powered. Lower profile ones could easily sit right on top
@erik618015 жыл бұрын
check your speaker impedance and the sum of all of them. i run car audio speakers for surround..my unit gets pretty toasty because of that.
@cjlhessing5 жыл бұрын
True! I upgraded to another brand and have noticed how little heat it puts out compares the the Onkyo. They’re like mini ovens!
@goodun60815 жыл бұрын
@@erik61801 , most audio-video receivers need a minimum of 8 ohms load on each and all channels. Many customers are unaware of this and will run 4 ohm speakers, or parallel speakers on the main channels, or run the A&B speakers simultaneously, or use the receiver to run speakers outdoors or throughout the house. These units were just not designed for that kind of Duty!
@iblesbosuok5 жыл бұрын
That's why I hate BGA. Dust deposit, self desoldering etc etc Cheers from Indonesia
@jonahtacastacas86722 жыл бұрын
Thank you. I watch your video yesterday and apply it in the next morning. Now it’s working. Your video was a big help. Thank you very much and more power.
@liquifire44983 жыл бұрын
It friggin worked! I used an 800-watt heat gun for 3 minutes at a distance of 6 inches and now my tx-nr809 is functioning again! Fingers crossed it lasts til my next upgrade. Thank you so much!
@regis0807853 жыл бұрын
Hi dude. Your onkyo is still working??
@liquifire44983 жыл бұрын
@@regis080785 Yep! It's been going strong since. I'm going to keep testing for another week, and if I don't have any issues, it's going up for sale.
@regis0807853 жыл бұрын
@@liquifire4498 finger cross 👍
@mastif764 ай бұрын
Took my broken Onkyo from basement just to check if I can’t fix it on this way and guess what…..it worked 💪💪. thx a lot
@boyceburns18232 жыл бұрын
I've worked on this same problem and it is as you say, it is across the board but I don't think changing the DSP chip is going to solve anything. The problem is the extreme amount of technology compressed into that little chip. The chip is like a CPU in a computer, it needs a heatsink attached to it but the problem I've noticed is there is no mounting holes to hold the heatsink to the board, at least on some of the boards. (like the one you are showing us in the video) I've spent a lot of time and work on this problem and I do have proto-type solution in the works. Some of the boards have a thru hole on each corner of the DSP chip and with these holes I've attached a heatsink with a custom made mount to displace the heat generated by the DSP chip. Only time will tell at this point if it works. (fingers crossed)
@bikdav4 жыл бұрын
Thumbs down? Not from me. At least you knew where to look and how to experiment with finding the problem.
@petertaylor63694 жыл бұрын
Great tip thanks for the information. I've just fixed my ailing Yamaha RX-V673 amplifier which also has the same chip, luckily I was directed here from the Yamaha forums.
@leelaughren68622 жыл бұрын
Thanks your advice worked. Ran my heat gun over the chip for 35-45 seconds while shielding the four sides and connections are now made. Heard it click so new the switch was doing its job. Thanks again!!!!
@brony4life19825 жыл бұрын
I might jinx it, but I gave a friend of mine my folks old 1999 Onkyo reciever and it's still kickin, and I have a used Onkyo reciever that's going strong. I hope I don't ever have this issue. Love your videos
@skycarl5 жыл бұрын
When I first saw the title,,, I thought it said, " trouble over Tokyo " and I thought, what the heck is Dave doing now lol. Then I read it again and realized I need to clean my glasses. ;p)
@kindanyume5 жыл бұрын
snds like u r taking lessons from my mom when her glasses were on her head but she was scouring the house trying to find them...
@arthurdanielles47844 жыл бұрын
🤣🤣🤣
@arthurdanielles47844 жыл бұрын
@@kindanyume 🤣🤣🤣
@kindanyume3 жыл бұрын
the funniest part is my wife just pulled the same move last night.... lmao
@christianbergeron14072 жыл бұрын
Had same issue, did not believed it would work. Initially it did not, but after that I took the board off, so I can flip it, and did the light thing on the underside over the soldering and VOILA, it is now working! I will put a heat sink on that chip to hopefully have it last longer (I read that the sticker that come with cheap heat sink is not transferring heat correctly, so I will use thermal paste) Thanks for the info.
@petecfla4 жыл бұрын
Thank you for posting !! I have the same exact receiver with the same exact problem. Going on amazon to but a heat lamp to see if it will fix it. Cheaper than buying a new receiver. Great Post thank you !!
@markusk.76212 жыл бұрын
You are my hero! Did this yesterday on my Onkyo TX-8050 and it works again! The only problem was to get a 50watts halogen-bulb because (in Germany) it‘s not allowed to sell it anymore regarding energy efficiency, so there are only led- lights left. But at least I found one in the internet. Really fantastic! I will now just put a heatsink on the chip and maybe install a little cooling fan to prevent the chip getting too hot in the future. Thank you!!
@0rigpumu2 жыл бұрын
How long do you have the 50w halogen lamp switched on to heat the chip?
@markusk.76212 жыл бұрын
I had it burning for 7 minutes and then took it off so that the chip was able to cool down.
@markusk.76212 жыл бұрын
7 Minuten, dann runternehmen. Ich hatte zur Sicherheit eine Alufolie über die Platine gelegt, in die ich ein Loch gemacht habe, sodass nur der Chip mit der Lampe in Berührung kam.
@0rigpumu2 жыл бұрын
@@markusk.7621 Ich werde das mit meinem Pioneer sc lx86 auch probieren. Der hat genau die gleichen Symptome und ich hoffe sehr, dass es klappt. Anschließend kommt ein Kühlkörper auf den Chip. Pioneer kann keine Ersatzteile mehr liefern. Also Platine austauschen klappt nicht.
@markusk.76212 жыл бұрын
Wünsche Dir dass es klappt! Für mein Modell gibt es auch keine Ersatzteile mehr. Ich hab bei mir auch einen kleinen Raspberry- Kühler draufgemacht und dann zusätzlich noch einen 80mm Noctua- Lüfter mit low-noise Adapter eingebaut, der die Luft von dort weg aus dem Gehäuse zieht.
@roderickroderick72165 жыл бұрын
You should have a air station already if you are repairing electronics. And the chip came to life not by “melting the solder” but by heating the internals of the actual chip. It’s the internals that are damaged not the solder connecting it to the board.
@calvinpoppen6652 жыл бұрын
Started having issues with my HT-390 and then the sound stopped...No other video I found did anything to help.....this worked...Used a 1500W heat gun for about 3 minutes...let it cool for a minute and viola, I had HDMI ARC sound again....Thanks for the post...
@inconspicuous-nobody Жыл бұрын
Can I ask how long yours survived after the fix? :)
@calvinpoppen665 Жыл бұрын
@@inconspicuous-nobody it lasts about 3-4 months...I had to recently use the heat gun again...Kind of a pain, but cheaper than buying a new receiver.
@inconspicuous-nobody Жыл бұрын
@@calvinpoppen665 Much appreciated!
@nicholasbrown83845 жыл бұрын
I would avoid using the heat gun due to the high risk of damaging the DSP and receiver because heat guns don't have the reliable temperature regulation that hot air rework stations do. Hot air rework stations will let you set the right temperature and come with smaller nozzles so you can direct the hot air exactly where you need it instead of cooking neighbouring parts
@amihaikopel6134 жыл бұрын
What is the right temperature? What is the right duration time for the heat? I have a reflow station at work. I think I have the same problem, when I start up the receiver there is no sound. Then, I wait for ~15 minutes so the chips will get hot. Then I power off and on and the sound is back (till next time).
@animarkzero3 жыл бұрын
@@amihaikopel613 The temperature you set depends on your rework station its between 350-400°C When you Re-flow watch the chip closely ! A microscope or a good magnifying glass is a must. The chip moves very slightly when the solder melts. Then you tap it very very gently to confirm that the solder is liquid. Stop heating immediately! If you tap it too much its game over unless you can Re-ball and have the right Re-balling grid!
@doublejay744 жыл бұрын
Thank you kind sir. I used a heat gun instead and it literally worked in seconds. Saved me money. I was about to go out and buy a sound bar. Subscribed!!!
@12voltvids4 жыл бұрын
I didn't have a heat gun handy. My amp is acting up again, will work on it again some day.
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@doublejay743 жыл бұрын
Quick update: My receiver doesn’t initially work on start up so I apply the heat gun for a few seconds and it works. About a minute later, it’ll give out again and then I reheat it again and it stays on for the rest of the time I’m using it. The only downside is the heat gun is literally resting next to the receiver should it give out. I’m just waiting for the day it completely craps out. A new receiver would cost me around $400.00 from what I’ve seen on Amazon. Not bad but I’d rather not go there. Times are tough.
@gryanm3 жыл бұрын
That's what I was gonna do...but my receiver is only missing one channel out so far. What temp should I use for a heat gun, and for how long?
@atschirner5 жыл бұрын
Our Onkyo 708 and 717 both had bad chips. One repaired under warranty and the other required a replacement DSP board. Two newer models are trouble free so far.
@TrevorRchannel5 жыл бұрын
I have a Onkyo NR616 and an NR818 and they both went back to Onkyo for warranty repair for exactly the same fault! Great video, nice to know what caused the failures, now that my amps are repaired I have a 5V fan sitting above the rear of the amp (powered from the rear USB) to help stop it overheating again.
@aksolartechnologieskriskan66682 жыл бұрын
I have the nr616 with no video output
@jillcroft11503 жыл бұрын
It worked!!! I have a NR626, put a heat gun on it on low for a few minutes. THANK YOU SIR!!
@swcrites5 жыл бұрын
thats a creative and pretty cool troubleshooting trick. i love it! thanks for all your videos, you have taught me a lot about electronics over the last several years
@lerrynhawke33752 жыл бұрын
OMG!! It worked!!! I don't know how long for but it actually works!!!! This is the best life hack I've ever come cross.. thanks very much
@12voltvids2 жыл бұрын
Mine lasted 2 years before becoming problematic again.
@dans55955 жыл бұрын
i did this with a pioneer about 4 years ago. still working.
@Sanamppa13 жыл бұрын
Thank you! It worked for me 🤘 I used hair dryer for couple of minutes.
@greenmarine5 Жыл бұрын
The problem is not with the Chip, the problem is with the solder and the integrity of the mainboard material. Neither could handle the heat, which is sad because Onkyo in my opinion is one of the Best sounding Receivers on the Market.
@12voltvids Жыл бұрын
BGA,. Bloody Garbage Assembly
@spaceysound5 жыл бұрын
Good tip, will try that on a device I have that has a bad system chip. You could stick a heatsink on it, might stop it recurring as quickly.
@godkast99044 жыл бұрын
Good sir, I owe you a beer. I reflowed the chip with a heat gun and stainless steel funnel (works great for BGA parts btw, as you can get them typically in a set of several sizes and they give you precision control of the airflow) and BAM the sound is back. Sure it may not last, but the fact it worked is enough for me to say thanks.
@Stoney3K5 жыл бұрын
The same problem was also present in a batch of Denon and Marantz NR series (which presumably use either the same board or the same chip). Onkyo had an extended warranty for their NR receivers because of this problem, and my Marantz was simply RMA'd and fixed under warranty. After replacement of the HDMI/DSP board it worked fine ever since.
@artomajuri49223 жыл бұрын
I used a heat gun for fix and helped at least for time being. So thnx a lot!! TI has a new version of chip available, but selling only to "certified" customers? I.e. to companies who are their service partners?
@PileOfEmptyTapes5 жыл бұрын
Oh, I never knew it was the DSP chips themselves that were faulty, always thought it was just bad soldering / inadequate cooling. Bummer. I better get a heatsink onto the one in Dad's TX-NR616 (thankfully not used much).
@FirstGenToyMachine3 жыл бұрын
Onkyo HT-R590: Worked for me too! I have a halogen flood light in the ceiling right by my receiver. Just went to home depot, bought a halogen flood pigtail in the lighting section, took some scrap wire, twisted and soldered the ends to fit into the socket in the ceiling and butt connected the pigtail on the other end to reach the reciever. Plugged the bulb in, flicked on the wall switch. Baked the Texas Instruments chip for 5 minutes and it's working! Cheers! Cheap fix. I know the chip should be replaced but I'll be replacing the reciever before that and if I can keep this going, I will. Cheers!! 👍
@JR-nj8le4 жыл бұрын
I have just purchased this Onkyo amp because I had 2x Sony STR DE475's which have the same issue with relay not clicking for sound so I'm worrying now - anyway my way is to hit it from the LEFT at the precise moment when it CLICKS - sometimes I have to try it 5-6 times but it always worked so far;)
@loaked3000 Жыл бұрын
Poor Onkyo, I remember around the mid 2000s all of them had HDMI switching issues that effected almost all of their receivers. I didn't know they had even more issues recently. I would never buy an Onkyo receiver unless it was a 2 channel one but even then given there horrible reputation and astronomically high failure rate I would just assume skip them all together. They made some great stuff though up until the late 90s.
@AThreeDogNight5 жыл бұрын
Yeah I've seen you fix TV's as well using this method. Thanks Dave.
@jasejj5 жыл бұрын
My 414 was repaired under Onkyo's extended warranty in 2016 at 4 years old and is still running. Onkyo had a problem and committed to standing by its customers. I can't see Bose doing that outside the US that's for sure.
@kindanyume5 жыл бұрын
Also note this is one of the reasons I am 1000% in favour of pre/control amps and seperate power amps! Not only is thermal management easier but even if the pre never had a failure when it comes time to upgrade etc it could help save $$$$ since onlt the pre would need replacement In my own case I have a very nice Denon 4300 butand I can build another custom power amp (multichannel) to use with the Denons pre-outs though my unit dooes have very good onboard non-IC based power section (umlike cheaper units like my old kenwood) I do wish the mfrs would offer the dsp/pre seperately from power amps or at the least build in an "off" setting to 100% tuen off thw power for onboard power. That and i they wont spend the few cents for added heatssinks as OEM allow the consumer to do such w/o voiding any warranty etc
@shuhradk Жыл бұрын
Would you mind sharing some of the pre-amp and power amps combos you have used?
@kindanyume Жыл бұрын
@@shuhradk no s Dont mind but other than a few peesonal pieces i havnt worked with such the same as i did yrs ago That said when i worked with many goodies 99% of with i couldnt afford i was lucky to get exp with everything from old school technics/pioneer/denon/yamaha to carver to rotel bryson and many others. As for personal i want to find a nice carver 27 or similar to replace my temp carver.. with is in place of my very old kenwood with is replacement for a cydtom hand built unit that some scum stole from my yrs ago Add to that a 400t of i can find one i can afford (and mod to mkii) to go with my 55x for 2ch+ use of mixed with my 505.. of my denon 11.1 ch proc reciever For HT use
@manumanu9779 Жыл бұрын
my Onkyo 616 having sound output issue and am gonna follow your tips for quick fix.
@dcarpenter852 жыл бұрын
I have an Onkyo TX-NR509 that I purchased in 2011. About 3 weeks ago, we started noticing that the speaker relay didn't seem to want to click on when powering the device on for the first time every day. Turning it off and back on would bring the speakers back. Last week, it finally reached the point where the speakers no longer clicked on at all, even after multiple reboots. I went ahead and purchased a new Denon receiver as it's been on my to-do list for a while (Need HDMI 2.1 support). I am going to attempt to repair the DSP as you suggested just so I can hand me down this Onkyo to someone else who may find a need for it. Thanks!
@jaspersiegmund2 жыл бұрын
Could you let me know if the repair worked? I have 616 with the exact same symptoms. First time it doesn't work, off/on usually fixes that but sometimes needs a few tries before it comes on. Up to now it still works but won't be that long probably. Would like to know how reliable this method is.
@dcarpenter852 жыл бұрын
@@jaspersiegmund It worked for a few weeks and then stopped working again. I gave up on it and dropped it off at a local e-waste recycler.
@jaspersiegmund2 жыл бұрын
@@dcarpenter85 thanks. Guess I'm going to keep an eye open for a new receiver then.
@dcarpenter852 жыл бұрын
@@jaspersiegmund If it has the features to suit your needs, I can recommend the Denon AVR-S760H. It is what I ended up buying to replace my 509 and I have been thrilled with it.
@arthurdanielles47844 жыл бұрын
Interesting to note that they started = Osaka Denki Onkyo K.K in 1946. Immediately post WW2.Over the decades they've specialized in AV systems and some amp units? Ah I love IC systems 😆and have watched a few hot air removals (NOT Onkyo) sometimes the solder removed and re 'tinned' before replacing the IC and the unit works fine after which kind of proves how wonderful and let's remember this, a machine installs those ICs not a human being - a machine! Basically heat and flash soldering in one which inevitably ends up with some having weak or poor terminal conductivity. Onkyo definitely not the only ones re this issue. Hmm where did I put my apple...😃Great vid as always and an excellent fix if it works and if you have one of these you've acquired from a thrift or charity shop et IF it works even for a few years after? 😃 where did I put my peanuts.. 😁
@subseadrilling4 жыл бұрын
I used a heat gun carefully on the DTS chip, now its working again!! Thank you for the tip, money saved:-)
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@GeorgeGeorge-xj2bc5 жыл бұрын
It is a BGA package chip and soon or later those chip tend to form dry joins in their solder balls and cause problems.The number one problem of all modern electronics is the Pb free solder that causing bad connections from the begining and getting worse as the time passes by.In bga chips that balls are underneath the chip and acting also as heat transfering path from chip to the pcb the dry joins problem is even worse.
@kd5ozy5 жыл бұрын
watt is the wattage on that lamp you are using? I need to get one of those. I have been using my hot air rework station for that
@snowyrain57302 жыл бұрын
That's a halogen MR (mirrored reflector) bulb and they're usually 30-50 watts... but be careful, they get VERY (VERY!) hot!
@willhelmx83885 жыл бұрын
Hi you all, in many cases there are problems with solder connections, especially after the change to lead free products... reheating can be one way to start... and with something as simple as a Halogen lamp...nice video :-)
@MrDuneedon4 жыл бұрын
Hello! I have an Onkyo TX-SR313 and it was a great receiver for me for years -- but not quite as long as I wanted it to be! -- and it inexplicably stopped working. I thought the problem was originally the speakers, but now I'm more convinced than ever it's this chip issue. I'm gonna give this a go and see what happens. What the hell!
@joeydigital632 жыл бұрын
Excellent video sir. My TX-NR585 just failed on me. NOW I have to go find a small halogen lamp to do this troubleshooting. Sheesh.
@artv4nd3l4y2 жыл бұрын
YES, I bought one off Ebay and it was defective out the box. Got my refund, and just did this and now it's working.
@rolf_reichts5 жыл бұрын
I really enjoy watching your videos, as a complete layman! Maybe you repeat your diagnosis and other comments various times to make sure the message gets across, which is probably very good teaching style. I find it sometimes a bit too much. (You must have said 5 times that these AV-R have problems with the DSP... ;))
@odotb99165 жыл бұрын
I love this guys videos, but you're right he does repeat himself a lot!
@davefetters32904 жыл бұрын
Awesome! My NR609 just stopped outputting sound. Hit the DSP with 60 seconds of hot air from a heat gun and I'm back in business!
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@davefetters32903 жыл бұрын
@@vortexor1 Unfortunately it sopped working again a week later. Ended up trashing the receiver.
@alexherget5 жыл бұрын
Nope. Big thumbs UP !! Great demonstration. Great vid.
@garyrichards4075 жыл бұрын
Thanks for the info, mine has been dead for about a year now. Mine started by being intermittent. Now I can try your method and not be out anything because I was considering junking it.
@12voltvids5 жыл бұрын
I'll put my old one up again and bake the chip a second time and see if it will come back to life again. As I was saying I got 3 years out of mine before it went out again, and because I had another older unit I just swapped it.
@johnrobinson3575 жыл бұрын
Too much tension on the bond wires when the Ic's were in the assy process. A somewhat common fault not limited to BGA devices. The BGA method has always had many issues over the years, in general the larger they are the more problematic. Too much heat to initiate ball flow. Heat is not kind to components.
@ChipGuy5 жыл бұрын
It is always this BGA case style. Not only from Texas Instruments. But DSL modems from AVM use similar DSPs from TI with same but bigger cases. They suffer the same problem (source: had a lot of them failing, own IT). Mac internal graphics card: Same case style, same issue with Flip Chip technology (Source: Rossmann Repair), Industrial control using some TI DSP:: same problems (Source: Work). So whenever I see those BGA cases with the thin FR-4 PCB And the molded top: I get suspicious. Maybe that's the reason new ICs are not using this hounsing anymore.
@arjunmadan30752 жыл бұрын
Suffering since years. Finally solved. Amazing:)🙏🙏🙏🙏🙌🙌🙌🙌🙌🙌🙌
@alanarmstrong23235 жыл бұрын
Darn leadfree solder.
@12voltvids5 жыл бұрын
That is part of the problem.
@Chupacabras2225 жыл бұрын
I doubt the solder is the reason here.
@12voltvids5 жыл бұрын
@@Chupacabras222 The chip is the likely root cause of the problem but the replacement chips are no better so the problem will occurred again down the road.
@andygozzo725 жыл бұрын
@@12voltvids if its solder trouble, couldnt you ram some liquid flux in, it, try to get it under the chip, then heat it?
@andygozzo725 жыл бұрын
bring back through hole components 😉
@nwstraith4 жыл бұрын
This fixed my RT590! Thank you so much! Though we'll see how long it lasts, at least it's working again.
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@nwstraith3 жыл бұрын
@@vortexor1 No, the solder broke again. I gave up on it and bought a new receiver
@vortexor13 жыл бұрын
@@nwstraith thanks for that information! how long did the fix worked?
@nwstraith3 жыл бұрын
@@vortexor1 a few days perhaps. Maybe I needed to hit it with the heat gun for longer, but I was getting nervous about cooking the board.
@Chocobopsu Жыл бұрын
Thank you so much for a nice, easy to watch and understand video. My Onkyo HT-R591 clicks like twice (I guess speaker relay?) But it doesn't sound like it clicks the last time. I usually leave it on for a couple hours and it will eventually kick sound on. However now the sound will not come on at all after an entire day of being on. :( It seems like I was inevitably heating up the receiver and eventually it would kick the sound on.
@coyote_den5 жыл бұрын
I don't know what Onkyo was thinking but their receivers run stupidly hot doing nothing. I had one you couldn't touch the top of after an hour. (even with John Cage's 4'33" on repeat) Ended up giving it to a friend, after a couple of years it developed a bad AC hum in the left channel. I guess the caps dried out.
@brianhenry21345 жыл бұрын
I would take the chip off the board, Reball the chip, you can buy a chip stencil and then use leaded solder that way it has a higher melting point. There are cold/cracked joints under that chip. Then when you are done put a heatsink on the chip by using thermal conductive glue. That is my Permanent Fix.
@12voltvids5 жыл бұрын
Yes I agree that it is most likely cracked solder joints under the chip as mine lasted over 3 years before failing again, which is as long as it originally lasted but if going to the trouble to remove the chip it should be replaced I'd available. I have had good luck with heating with lamp or heat gun. The laptop I used the heat gun on is also still functional
@batsonelectronics5 жыл бұрын
NO. I have worked with bad BGA chips, it is inside not the exterior solder. That bulb did not heat the solder to 217C as that is the melting point of lead free solder. The bond connections in many BGA chips have been a problem since the late 2000's. Nvidia and AMD have had GPU's with that problem with Nvidia being the more lately. Reballing won't fix the issue except it will seem like it as heating it up to reball will temporarily fix the bond connections and you will think it fixed it. That bulb didn't get hotter than 100C so that is no where close to melting 217F solder. Keeping the chip cooler will make it last longer so once you heat the chip to fix the bonding, use the heatsink to help minimize the chance of it coming back. I found with Apple GPU's that keeping them under 170F makes them last way longer before they fail again. I did that with better thermal paste, high end Fujipoly Thermal Pads and a faster fan speed using SMC FanControl software.
@BjornV785 жыл бұрын
Everybody thinks it's a problem with the solder between the board and the chip, IT'S NOT !!! The problem is the chip itself is bad, this can be due too much heat during working, or due a production error of the chip. In those chips, there are a lot of transistors etc.... if 1 transistor in those chips failed, the chip still works, but all the other components have to deal with the current and gets hotter, until another transistor dies, this is like a chain reaction. At some point there are too much damaged components in the chip, and the chip cuts off. Why it's not the solderjoints between the board and chip ? Simple, because there is NO solder that melts under the 150°C. This problem with failing chips is a common problem on many notebook motherboards, and yes heating the chipset chip or VGA chip temporarily fix the problem there also. BUT, those chips will also work if you heat them with a high performance hairdryer, and those hairdryers blow arround 100a110°C. Those temperatures are too low, to melt any solder, lead or leadfree solder. So if heating a chip with only 100a110°C already temporarily fix this problem, then is not a problem with the solder. I have fixed many notebook motherboard with only a hairdryer, some failed after a few reboots, some after a week and some still working after years. My guess is that there hairline cracks inside the silicon chip, that reheating temporarily joints them together, and if you rise the cooling of the chip, the next breakdown can be delayed.
@snowyrain57302 жыл бұрын
a 50 watt MR16 bulb (which is what this is), reaches 500*F. (420*C) FYI
@dereko.17192 жыл бұрын
I'm lucky enough to have had my unit fail in 2021 and Onkyo told me to pound sand basically. I bought a heat gun and tried heating the chip. No dice. So my last experiment before junking it would be to do my first ever chip removal + reballing... should I even try? Already shelled out money for a heat gun, which I can use elsewhere, but buying equipment for repairs that I know nothing about... down to learn, but ready to give up and buy a non-Okyo receiver as well.
@Yinsot5 жыл бұрын
Amazing how heat alone can re-shuffle the chip back into working order.
@12voltvids5 жыл бұрын
It either reflows crystalized bga connection and if that is the case it is a long term fix, but if the problem is the bond wires that attatch the silicon to the outside world the expanding epoxy case reconnects them and they work for awhile. The only permanent fix is to change the chip because you never know when this symptom is present if it is a bad connection or the chip that is causing the fault.
@geraldv2035 жыл бұрын
@@12voltvids I suppose that it's exactly the same problem with the Playstation 3 GPUs and some other popular chips made around 2005 (plus the move to leed-free soldering)? nVidia chipsets, for example? Edit : Already written by starscream 79 ^^
@t0nito5 жыл бұрын
@@12voltvids Since that seems to be such a common problem and since it's heat related I would put in a heatsink on that chip after replacing it.
@1Stormrider13 жыл бұрын
@@geraldv203 I was going to comment that before I found your comment. It’s the same issue as the PS3’s, which wouldn’t have been a problem if they used lead solder. For the chip in the video, a heat sink would’ve prevented the problem from happening. I’m going to attempt a repair with a heat gun and use a heat sink if that fixes it.
@johnmessina97214 жыл бұрын
I have the Onkyo TX-NR5009 and the sound did go out about a year after I bought it. Luckily it was still under warranty and I brought it to a specialist that Onkyo recommended near me and he replaced the entire audio board. It has sounded great ever since...knock on wood.lol
@12voltvids4 жыл бұрын
I wasn't so lucky. I would have had to ship mine to new York and pay freight both ways. Cost to repair under warranty higher than new. So i found an older one for 40.00 that doesn't have this issue.
@davidkettley66854 жыл бұрын
Thank you so much... I had the chip changed about 18 months ago and it just recently started playing up again. This done the job. Incidentally, I also noticed my remote from my phone did not work and this seems to have rectified that problem also! Again, thank you!
@vortexor13 жыл бұрын
Does it still work? Thanks and best regards
@davidkettley66853 жыл бұрын
@@vortexor1 I got about another 2 months out of it, but finally it died. It is a temporary fix, until you can get it replaced. I just brought a new receiver from Denon as I was absolutely tired to keep wondering if the Onkyo would give up again.
@vortexor13 жыл бұрын
@@davidkettley6685 thanks for the information!
@stefaness21532 жыл бұрын
@@davidkettley6685 Are you satisfied with the sound of your new Denon? I also bought one after my Onkyo tx-nr509 failed with no sound (since i did not know of this video back then!). But compared to the Onkyo the Denon sounded extremely flat and not voluminous at all (though the setup was the same with 5.0 speakers). I ended up returning it and bought a used tx-nr609 from ebay for about 200€ just a week ago.. the sound characteristic is exactly what i expected the Denon to be and even a bit better than on the 509. The added bass of the Onkyos is just perfect to compensate my lack of a subwoofer. Maybe i can fix the issue on my 509 now with the help of this vid and resell it for a higher price than it being in state "defect".
@davidkettley66852 жыл бұрын
@@stefaness2153 the sound is definitely not as rich as the Onkyo, but the reliability is spot on. I tend to find it depends a lot on the source material.
@JanaBuvari4 жыл бұрын
time to give this a go, sadly australia missed out on any opportunity to get theirs repaired as there's no repair places in australia! Thanks for the video, ingenious way of heating the chip too! haha
@12voltvids4 жыл бұрын
Should work for awhile. Mine lasted 2 years before acting up and is sitting in the corner. Will give it another go some day and see if it will work again. I am using an even older one now for my home theater amp. All i use it for is watching tv. I liked the one that broke because it had very good input switching for all my legacy equipment. Nee ones only have hdmi so I can't connect my old dvd player, laserdisk or vcr.
@JanaBuvari4 жыл бұрын
@@12voltvids I'll report back with my results! Fingers crossed and thanks again! I enjoyed the video 😁😁
@tueftelwerkstatt Жыл бұрын
Thank you so much for that video. I did it exactly as you suggested and it works again👍👍👍
@thebasementonlinegaming53944 жыл бұрын
I bought one today and ..tadaaaaa i am finding myself looking at this video...no pun intended. I am going to get my money back
@Nemsterfly3 жыл бұрын
Thank you for your advise. Fixed mine thanks to your advise and knowledge.
@tedjones1125 жыл бұрын
Is there much difference between cheap AV receivers ? Pioneer vs Yamaha vs Denon vs Onkyo vs. ? Any one any Better quality than the others.?
@danhowe60052 жыл бұрын
Just put a heater on top for a couple minutes and back on the speakers came thank you very much