Audi Timing Chain & Timing System Replacement DIY (Audi 2.0T CAEB, CPMA, CPMB, CHJA Engines)

►The CAEB, CPMA, CPMB, and CHJA Audi 2.0L engines often require replacement of the timing chain and an overhaul of the timing system as a whole. Our Audi timing chain replacement kit contains everything you need to replace the timing chain and the timing chain tensioner, timing chain guides, timing chain cover & gasket, a full oil change kit, and the coolant you will need to refill and bleed your system.
This Audi 2.0L timing system overhaul covers the EA888 Gen 3 engines with the codes CAEB, CPMA, CPMB, and even the CHJA hybrid engine. If you are experiencing slow crank or no start we recommend that you first scan the vehicle for faults. If the P0016 Cam/Crank Correlation fault shows, it's more than likely time to replace your timing chain.
Before replacing your timing system, we recommend a few diagnostic steps:
Check base timing
Perform cylinder compression test
Perform a cylinder leak down test
If you find low compression or cylinder leak, we recommend using a borescope to check intake & exhaust valves for damage. If the valves are bent, you will need to replace them as well.
If it's determined that you need to replace your timing system, follow our step-by-step Audi 2.0L timing system replacement DIY where Aaron Davis, FCP Euro's Audi Catalog Manager, walks you through the entire process on a 2017 Audi Q5.
00:00 - Intro
02:14 - Tools Needed
03:22 - Job Start
04:39 - Coolant Drain
05:22 - Front Clip Removal
16:39 - Belt Removal
17:50 - Upper Timing Cover Removal
19:45 - Setting Top Dead Center
22:00 - Crank Pully Removal
22:32 - Lower Timing Cover Removal
24:21 - Cam Bridge Removal
26:42 - Timing Chain Removal
30:30 - Balance Shaft Chain Explanation
31:29 - New Timing Chain Install
33:06 - Timing Guides Install
36:49 - Lower Timing Cover Gasket Procedure
37:44 - Lower Timing Cover Install
39:28 - Crank Pully Install
40:51 - Tensioner and Belt Install
41:45 - Cam Bridge Install
43:09 - Upper Timing Cover Gasket Procedure & Install
44:34 - Front Clip Reinstall
56:38 - Coolant Refill
57:44 - Oil Refill & Check
59:18 - Wrap-Up
#audi #audiq5 #fcpeuro
Buy This Kit Here:
www.fcpeuro.com/products/audi...
Buy Timing Tools Here:
www.fcpeuro.com/products/audi...
Buy Oil Filter Tool Here:
www.fcpeuro.com/products/merc...
SUBSCRIBE: kzbin.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

[@brianarroyo1638]

I just want to say I wish I had this video 2 years ago and also everyone don't be scared to try this! I was in a bit of financial situation at the time so I did this my self and I never worked on engines like this, I've only have done the basic plug and play parts like spark plugs and brakes but I did this job with my younger brother and dam it was a bit tuff but alot of fun learning and I did this all in my apartment complex parking space. But once we completed the job , the smile my brother and I had once then engine was running nice and smooth at the first start up was priceless. Just do it!

[@sailorbob74133]

How did you guys manage to get the crank bolt off? Mine's on so tight I can't even get the starter to knock it loose.

[@samuelwh4775]

Ngl I’m really scared on doing it because it seems like if any little thing fails, it’s going to destroy the engine after 😓

[@joeg2286]

@@samuelwh4775 don’t use this video for reference , naptown tuner is way better and will actually show you the full job

[@fiolds350]

Good shit bro!!!!! Love the story

[@gerardolopez8715]

@@joeg2286 show me the link , seen him just paraphrase the whole job

[@SL1D3YB0I]

I’ve learned from this video that a 90 degree hook pick is a VERY important tool

[@trm64]

Just finished this today on a 2011 A5 that we bought at auction. It had the cam / crank correlation code and about 150,000 miles so we tackled it with this video as our primary reference. It fired right up and sounded great with no leaks or issues. The test drive was amazing! Smiles all around :) Thank you so much for posting such an informative and thorough video.

[@fcpeuro]

Excellent work, glad we could wrench with you!!

[@kendrickxy1774]

Thank you so much for this! I was able to change the timing chain on my Aufi A4 B8. I had all valves bent and the timing was completely off. At first, watching all the steps to get to the chain made me sick to my stomach. But I went in step by step and today my car finally started after 2 months on jack stand. You guys are a blessing for putting such quality content out there for free. May the Lord of all things bless you many times over!

[@EFCLARK]

Duuuuudes this was sooooo well done. The speaking during the walk through, the editing, the plugs for the products u have , the camera angles and even the filler sound clip during the tightening and loosening sequences were all perfect. I watched this allll the way through! Yaaaaa I'm thinking maybeeeee tha guy with the Audi/VW tat knows what he's doing. My sex Ed class wasn't even this engaging! Excellent

[@cwilson2]

This is an excellent how-to video showing all the steps required to replace the timing chains along with some great tips and insights from Aaron. I consider my mechanical abilities around a 6 out of 10 but was able to complete the job in my garage. This job can be done by without removing the front carrier, but I would recommend removing it following the instructions in the video if you're doing this for the first time. Removing the carrier gives you full unrestricted access and full line-of-sight to the front of the engine and makes the timing chain replacement easier. I ordered the timing chain, tensioner, chain guides (3), lower timing chain cover (and VW-Audi RTV to form a gasket), upper timing chain cover gasket, crankshaft pulley bolt, as well as the CTA 1023 tool kit and the T40011 locking pins (3) from FCP Euro. Everything was shipped promptly and the parts fit perfectly. The video was the main reason that I purchased all the parts from FCP Euro; I really appreciate suppliers that put the effort in to make DIY projects easier for the weekend mechanic.

[@jawsone]

I don't even have a Q5 (own a Q3), yet still watched this all the way through😂. I was concerned when the crank bolt and vibration dampener was removed, and the special washer is fitted and crank bolt replaced. My workshop manual has a special tool for this step. You remove the bolt leaving dampener in place, fit a special locking pin, and only then remove dampener. This is to ensure spur gear doesn't unseat from crankshaft. I dunno, was just so casual, and no special tool, but it seems to have worked!! I don't have a chain issue, just some light oil seapage, so may just.silicone exterior of cover seal first to see if that slows things before taking on this beast of a job (Q3 is transverse so need to support engine from above, then remove engine mount and mount bracket) Awesome video. AAA+++ Right Angle Pick Tool FTW 😂😂😂

[@gertwolmarans6974]

Best, most descriptive video out there I have found. Being in ex Ford master tech working gor myself now, learning other vehicle's small tricks are gold. Thank you my friend. P.s glad to see I am not tge only guy who hates gloves.

[@nfaurerSLK]

Great video and super helpful, but can you guys remove the horrendous drumline?? It's awful.

[@3dauto]

Gotta say I'm very thankful for this video. The OE information is so complicated to follow, but with this I was able to do the job.

[@fcpeuro]

Great to hear!

[@nickoosthuizen2678]

Awesome vid been a mechanic for 52 years and I'm still learning something new everyday

[@fcpeuro]

Thank you for watching! Happy wrenching!

[@brencole7092]

I am in love with this video; as an automotive teacher and technician, I felt like I learnt all over again. Thank you very much, this helped me out with my A6. I also admire the dedication with the tattoo...

[@OperationXXX]

Thank you very much…. I always come back to your videos when I’m stuck.

[@JCe92m3]

Thank you so much for this video, I couldn’t have done the timing job without this. Only 2 things this video left out. There is another bolt behind each headlight holding the bumper cover to the car. Maybe it’s specific to the B8/B8.5, but I nearly trashed my bumper trying to pull it off. The second is the balancing tensioner and chain is super easy to switch out, and you might as well do it since you’re right there with it exposed. My balancing chain was also a little stretched

[@lazardjordjevic994]

Great teacher, great guides, great video, great chanel. I want to thank you for all your work and for sharing knowledge around the world!

[@NomadicCratic]

Phenomenal. These are the types of videos I like to watch. We need more videos like this on Y-Tube.

[@bayuaryanto4017]

Very comprehensive tutorial. Makes the job doable for diyers. Thank you

[@BrandonS350]

Thanks for putting these together. I'm watching this with my morning coffee before heading out to install the timing components on my engine rebuild this morning. The FSM has all this info, but it's super nice to see it being done in video vs the horrible drawings and awkward verbiage the FSM provides. Oh as a side note, my motor was at 80k KM and my timing tensioner was a bit less than 2/3rds to the sevice limit so that 65k mile estimate you gave would have been pretty bang on for my motor.

[@Mellchior]

I don't even own the vehicle in the video but was curious about the job. Video was so well done that it was fun to watch!

[@baljeetd]

Exceptionally well done! Better than anything else I've seen. Well done Aaron & the FCP-E team! Professional-grade guide!

[@ricardoarohenapagan9149]

Very clear and orderly video instructions.

[@user-xz7wy9xy2q]

GREAT Video! Clearly this is not for the faint of heart but you've made it seem less daunting.

[@pablovalenzuela9089]

Prob the best explination vid i have ever seen. Great job!!

[@Bryce.H604]

Awesome video man. Really well done edit and presentation. 11/10 man.

[@Chris-iw8gx]

I had the cams move on me, by waiting to lock them, after removing both guides...but I didn't notice any cam movement for you? My crank position didn't move, but thankfully have wrench clearance to slightly move cams into position. What a PITA and thankfully can figure out what to move where. I just worry about valve contact from TDC position and the cams moving. It was maybe 3-4 cam link moves to get things back together. For everyone else, I'd suggest removing tension(er), remove cam bridge and then immediately lock the cams before anything else. Fantastic video and thank you!

[@Grumpy262]

Very well explained thank you ,step by step and tools needed very good job 💯👍

[@danielcollins2617]

Hey FCP. great video that really helped me tackle this job with your kit. Just wanted to let everyone know that the crankbolt for the B8 (and probably B8.5 and B90 has a new 10.9 grade bolt rather then the 8.8 grade used in this video. The new 10.9 grade bolt has a different torquing procedure. The 10.9 requires 100nm then 180 degree turn. The original 8.8 had a 150nm with a 90 degree turn. Check the factory workshop manual.

[@coryjackson6034]

I could be wrong but that math seems to be the same once torque is set???

[@HA-yo2hn]

Excellent, everything done easily and in a simple way , thank you

[@fcpeuro]

Thank you for watching!

[@senaddulic9454]

BRAVO ! One of the best detail video !!!

[@rezabadei3229]

Outstanding video on all levels! 👍🙏

[@seanh3075]

Wow. Most informative video I've come across. Ex tech here hoping you'd provide sizes and torque specs. Nice work!

[@shahinhawk3127]

Thanks for your video. notice: before loosening the tensioner, you most lock the camshaft not after. min 29. anyway good luck

[@elgarfio4186]

Beautiful job well done and explained 👏, I'm going to try to get this done myself!!

[@singularity1bh]

I wish you guys performed these types of jobs for those of us without the capability to DIY ... For a fee of course ... Well laid out video ...👍👍

[@singularity1bh]

@@rayj33 Thanks a lot genius ... In your haste to TROLL me, your paltry brain missed my "Well laid out video" statement ... Unbelievable ... SMH

[@solmanJapan]

And the MVP award goes to the 90 degree hook pick! Damn that thing got a good workout

[@fcpeuro]

Sometimes just the tool for the job ;)

[@ashtonmarrero7932]

Excellent video, by far the best!

[@TR3NDSETR]

Brilliant Video, IM not doing the job but great to know the process and atleast I can understand what my mechnaic is talking about

[@tergo2479]

Me: "Hey what tool do I use to-" Aaron: "90 degree hook pick." Fantastic video guys, well done!

[@AudiA4-iv2pz]

Thank you so much, i did this on my 1.8tfsi cabb engine, on my drive, took me a day because i also did thr oil pump chain

[@djman474]

Thank you for the video it's very clear and detailed so professional

[@fcpeuro]

Glad it was helpful!

[@Cargaooversized]

Great video sir, VW/Audi need to provide those timing kits since they fail all the time !!!

[@alexescobar1281]

Great detailed content !!

[@sylvainst-laurent3631]

Great teacher . Well explained .

[@fcpeuro]

Glad it was helpful!

[@Olympiansunrise]

Awesome video! Thank you

[@mikimiki195]

Damn that was easy process 👍🏻👍🏻 great video

[@ygbado]

Great vedio. I just this job on my wife 2015 q5 2.0t it went great. Thanks

[@barthoylaerts2748]

Very nice video!! I never worked on this engine before but after seeing this video I feel pretty confident. So you dont need the diagnostic tools after this job? Thanks

[@harrell7455]

Very good video

[@marjoofficialvlogsl4642]

Thanks man for this video..today I do timing for Porsche macan 2.0 tsfi engine.

[@fcpeuro]

Woo!! You got this 😎

[@mfreakist]

Great video & cool tattoo !

[@davegladys9820]

Thanks! This video was one of my references during my timing chain install and it helped a lot!

[@mauricecastle5809]

Gracias

[@smartinez211216sm]

Before watching this video , Never would I have thought I'd be doing a timing on any vehicle. Wow let alone an Audi. Thank you for this amazing descriptive step by stem DIY educated video. It really isn't rocket science.. Thank god for Google KZbin our friend.

[@fcpeuro]

Our pleasure!

[@MyXXXcarlosXXX]

Good video! Can you make one for 3.0 tfsi?

[@samevans7753]

Epic job

[@davidboscaljon3787]

Great video!!

[@jellyd4889]

Wow. So impressed with the quality of this video. Clear instructions. Amazing. Will try it myself in 5 years

[@fcpeuro]

It will be waiting for you!

[@brkykpzky]

Hi fcpeuro, Thank you for the great job and perfect explanations. I have a question about the (non-return valve in the cylinder head which is the part number 06H103175B), On the repair manuel is writing that we should check the both of the non return valve before timing chain replacement etc. One of them Ok - you replaced it with new camshaft bearing bracket, but 2nd one - Did you check this valve in the repair process? or automaticlly you had already checked when you perform a cylinder leak down test? because I could not catch during the video. Thank you in advance.

[@thaoallen4023]

hi guys, you have done a awesome job, thanks heaps, wish you and your family having a wonderfull Christ X 2020

[@fcpeuro]

Thank you! Same to you!

[@thaoallen4023]

@@fcpeuro hi FCP Team, I wanted to order some parts of my audi A4, would u help me out with some parts of timing chains pls, thanks

[@jvb4218]

Well done. FCP should offer tool rental for jobs like this.

[@virtisconsole12]

Hey Aaron what is the opinion of using thread locker "blue loctite" on the tensioner T30s, the guides M10 TPSQZ and the lower timing case cover T30s? And what about the two head bolts you removed to install the tensioner tool should those bolts be replaced once finished with the tensioner tool? Should they have thread locker?

[@muhammadatifali5891]

Good healp

[@ivanvega2821]

Great video! I have a question, currently doing a chain job on a 2010 volkswagen CC. Vehicle presented P0016 and multiple misfires on all cylinders. While putting the vehicle on TDC, the exhaust and intake cams are not lined up where they should be. Both cams appear to be at roughly 12oclock position. have rotated the crank multiple times to see if maybe after several rotations the vehicle would line the cams up. No luck. Should I just take off the upper chain and guides and realign cams with a wrench manual? I appreciate any suggestions. Cheers!

[@jonathanforlin1854]

Hi great video. Are there going to be any major differences to a CPLA engine?

[@geminisruiz6967]

Excellent 😊

[@StarsAutoSport]

👏great stuff!

[@gee3883]

Do you allways replace the cam bridge with a new one? Thanks for the vid/tutorial.

[@sickvic3909]

Nicely done but if I have the 2015 3..0L super charged the chains are on the rear, correct?

[@ypautomotriz]

waaaao good job boss. after service, it need do some relearned in OBD2?

[@powersterk]

Nice & beautiful .👍👍

[@NiXFiX]

Very nice video! I see you list CAEB, CPMA, CPMB, and CHJA engines. Are CAEB and CPMA heads interchangeable? I have a 2013 Audi Q5 2.0 engine code CPMA with cylinder head part number 06H103064N. CPMA heads are hard to find outside of dealerships. CAEB heads are plentiful, but are a slightly different part number 06H103064L. Are they interchangeable? I would think as long as the head has the exhaust side AVS it would work. Thanks.

[@virtisconsole12]

I have heard that after releasing the pin on the timing chain tensioner the crank can slip a link on the chain , how do you reset the timing? Can you roll the engine CCW to realign the timing or do you have to go around CW every time? The cams are locked so it don’t think they’ll move the chain. Do you leave tension on the chain or do you release it to adjust it a link?

[@dogchainsaw3923]

Nice video

[@abdallanakhle8751]

Amazing !!

[@ricolam4916]

Is there a better visualization of the crankshaft mark and camshaft timing mark?

[@raulacosta8013]

Excelente Video y muy bien explicado; de lo mejor que he visto en la RED. La pregunta obligada es: ¿Cuál es el Costo de una reparación como esta en USA?. Saludos desde Cholula Puebla, México. Gracias

[@alexanderstefanxandraswedi5835]

❤🎉😊 Great job brother

[@michaelsmall6818]

Can I ask roughly what it would cost for a garage to charge for doing this job?? Great video.. very well done

[@kaoslopez1749]

I would like to know if is the same process for a Vw 2014 GLI Gen 3 CPPA

[@sstjacques]

Excellent video, but my engine is 2012 Q5 with 165k on OEM timing chain, so need to do balance shaft chain also before problems arise. Surprised to see that old chain, would not have bought the car if it was not done but it runs good still.

[@derrickhall-ek9xk]

Are there timing marks on this engine on some other Volkswagen you have to measure a certain distance but I see on this one it seems to have markings

[@elroz1675]

well, for 2014-2017 2.0 they updated the tensioner, as you said. There should be noticeably fewer problems with the chain on CPMB - can we say that? Hopefully so?

[@taylorspykstra9226]

So I have put the whole thing back together and I tried to start it and it sounded like the starter was turning the crankshaft just fine, but there doesn't seem to be any ignition. Before putting the timing cover back on i made sure the crankshaft turned freely, so i aussumed it was in time. I checked the connection to my ignition coils and I know they are in securely. Does this still sound like a timing issue?

[@fjjbikerider]

Great Job on this FCP team do you have the audio A4 B8 same engine??? truly great work. I ordered the kit from yall and am a DIY. thank you.

[@fcpeuro]

We love that you enjoyed this video!

[@jtg2737]

On the subject of timing which Audi models out there have the "timing components" between the engine and the transmission and when was this design phased into production if anyone knows please?

[@cameronross4140]

I am putting together a list of parts and tools that I need to do this job on my 2011 Q5 2.0T I believe the CAEB engine. The kit you use in this video does not fit my car as per your website states. The one that is compatible is very similar and in parts and price. If I buy the kit and tools that fit my car, can I still use this video to replace the timing chain?

[@elijahkeith5766]

How long does the sealant take to dry? Don’t you have to wait 24hrs before adding oil and turning the vehicle on?

[@CrazyDescargas]

90 degree hook pick most underrated tool 🤦🏻‍♂️

[@user-ug1lc5se4t]

If the oil screen on the camshaft bearing bracket is damaged, do I need to replace the bracket?

[@JustGameEverything]

25:30 You mentioned that engine is back to TDC. Wasn't it already at TDC when you started removing components at the beginning of the video? Awesome tutorial, ordered full timing kit (including the lower area) from you guys!

[@ch0wned]

Even several thousands of an inch of movement could indeed cause an issue.

[@joeg2286]

They don’t really know what they are talking about here unfortunately

[@paulkieffer1189]

Please make a video re sealing camshaft cover. Oil is leaking into spark plug but I’m afraid of the cam shafts coming out of proper time, alignment while re sealing. I want to replace timing chain while I’m in there.

[@tabaricurry4668]

They shouldn’t move while doing it. Just unbolt the right bolts for the vacuum pump that’s the only thing that’s difficult

[@richandshameless]

The kit in your description on the FCP site says 2013, is this the correct kit for a 2015 Q5 2.0? engine code is CPM

[@Veersa]

So my intake balance shaft seized up and pulled out and it wouldn’t turn. So now you’re saying I can’t replace it with a new one and new chain and everything and it won’t run?

[@davidwong2095]

Thanks you Can you show me when timing of how to ali back

[@maccasst]

When I disconnected the transmission cooler, lots of oil came out. Do I have to refill the transmission oil?

[@leticiajguyton5889]

Do you have a video for A7 or is it the same

[@hvacinstalacije1985]

Hi, I just want to know why you did not replace and chain kit to Oil pump ?

[@jonboi7694]

What is the special tool for the balance shaft?

[@O-RoD]

So how long did this job actually take?

[@ghostofsoufeasthoustone]

I’m having random misfires and I’ve done everything except the timing. But I have no codes for timing related issues. All cylinders have compression as well. Just did new injectors and carbon clean on valves. Does the timing make the car have random misfires? It only happens above 4000 RPM. Then the EPC light comes on and the check engine blinks. The code it gives is random misfires.

[@davea4037]

Excellent video. I have a 2013 q5 with just over 80k. I may tackle this at 100k if no issues pop up. Runs like new for now. Thank u, this really really helps.

[@fcpeuro]

It certainly doesnt hurt to get ahead of it Dave A , as when its too late, its too late. Happy to help!