E bikes 2021: Improve your Ebike's performance programming the S830 LCD and SW-900 LCD

[@TMAX48]

Holding down the down button for a few sec puts it in walk mode. To go into cruise mode twist throttle to required speed and then hold down the down button.

[@PrestonMiddle]

Cruise control process didn't work for my max cargo eunorau ebike...

[@chriswhan8648]

@@PrestonMiddle poppp0p

[@chriswhan8648]

@@PrestonMiddle ppqqq11qqqqqq1q1qqqqqqqqqqq

[@PrestonMiddle]

@@chriswhan8648 passcode?

[@halilibrahimkocoglu5899]

Thanks so much TMAX48. Now I know how to get cruise control. Yes !! You’re a gun mate thanks so much I always wanted to learn how to get cruise control work for just over 9 months lol

[@SeanMcNally-pg6vv]

Great information thanks 👍

[@AugustineEBikes]

Glad it was helpful!

[@ilyassert7874]

Your information is super, thank you so much

[@MrNewzealand43]

Life safer, thanks for great video.

[@stockey]

Almost everything is locked on my S380, is there a way to unlock it.

[@paulboucher4439]

Mine has the same thing

[@trini_boi2414]

When I set p07 to 47 my mph and trip is way off..my GPS say I'm going 19mph and the LCD screen is showing 35mph..when I changed it to 1 the mph is way much better so on my kit I believe it's 1 and not 47..

my 2000w hub motor, says i go over 50 kmph but i go walk speed. i have 29 inch, and in setup set it to 29" if i put it on 26" it still shows morekmph then i actaly go.. and sometimes it does not show speed at all, then it says 00 kmph. nc81f display , what can be the problem ? were to set it on when you have a 2000w hub kit ?

[@rickyc1130]

Hi, Could you please explain P11 setting as I think you may have skipped over it, thank you

[@duprie37]

It's skipped over in this user manual too (electricbikereview.com/forums/attachments/1528492757374_enoeco-user-manual-cs-s830-pdf.22814/). I've heard it refers to pedal assist sensitivity with a range of 1-24, but I don't really know what that means tbh. Default is 2.

[@dougfox9649]

The higher the number the lowertthe intialassistkicks in. Set it at 1 for maximum or a bit higher for more delay.

[@tallman145]

My Ebikeling display was showing 48 miles total . The next day after I turned it back on the miles dropped to 45 miles, strange. This happens twice. Any clue what is the problem ?

[@timcoates3821]

Thanks for the very informative video. I have the same display on my ebike. I programed the display so I could use the throttle but would rather just peddle. I now have the problem of the motor kicking in and out all the time this has only happened since I programed the throttle. I can't get the bike back to full time peddle assist. Any ideas how to fix this would be greatly appreciated. Thanks. Tim

[@JayrB]

My ebike is Movelo Electric Bike 36V 10AH 350W, the display only has settings P01, P02, ODO. Is there any other way to get all of the other settings? Help will greatly be appreciated. Please and thank you.

[@beatsbytani7875]

Po7 is was set 100 the who sold me the biek said to keep po7 at 1 I’m not sure

[@SoSimonSays]

up and down buttons didnt do anything, im using a suntour hsec system

[@cannonballebikesltd9660]

great information, thanks so much for this as its very difficult to find information, I was getting Error Code 8 due to the P-10 being set to 1, also the P-13 was set to 8 when I only had a 5 magnet PAS ring. Cheers Colin

[@thets3209]

⁸p00

[@trini_boi2414]

I don't believe this display has cruise control..i think it's called walk mode but they calling it cruise control..i really wish this display had a real cruise control tho..

[@Robertkwi]

so, where to buy this new sw900 for 35a?

[@johndonzell2640]

Is this display UART or 5s protocol. I need a new display for 5s protocol and can't find any at all. Uhg

[@Mishakol1290]

That setting at 47 when do you set it to that i have a 350w motor. I camt get my speedometer to read accurately and pedal assist mode lags greatly. Activating and deactivating.

my 2000w hub motor, says i go over 50 kmph but i go walk speed. i have 29 inch, and in setup set it to 29" if i put it on 26" it still shows morekmph then i actaly go.. and sometimes it does not show speed at all, then it says 00 kmph. nc81f display , what can be the problem ? did you fixt it ? i have a 2000w motor and shows way more kmph then i realy go

[@thegrizzly6804]

Im new to ebikes and please tell me can i replace a broken s700 lcd display with a s830? I have a gogobest and No matter where i look i cant seem to find anything telling me if my bike would be compatible with anything else. I would assume it would but im scared to buy the wrong on considering the prices

[@SeanMcNally-pg6vv]

I'm also curious about this. Did you ever find out if the s830 is usable??

[@thegrizzly6804]

@@SeanMcNally-pg6vv yes the 830 was not usable

[@molji5070]

Does anybody know the speed magnites on t rex air cycle

[@DIYTFY]

What setting saves battery power?

[@jshays007]

When I press the + and - keys together, the screen says "C" and I have 5 zeros below ... I can't access the Programming Modes. Do I need a Pin Code here?

turn it on, and staight after it on + and - for 2 sec then you get in the menu.

[@viajero5190]

Thanks bro

[@josephgeorgeejr7039]

Someone said you have downloaded this guide, lol iam just going write it down as u say them

[@JHOFF111]

What exactly does the magnets do? My particular ebike model is set for 1 can I bump that up to get more speed or should I leave it the way it is?

[@BretBratcher-zc2sl]

What type of LCD display comes with a new Escout Pro young electric , I don’t see any names or numbers

[@Anygodwilldo]

Mine doesnt work like it's supposed to, I just don't get it After trying to set everyhting, the battery dsiplay is showing empty and flashing but I know for a fact it's fully charged. The bike won't move now. And the display is stuck, I can't scroll thru options . Is it faulty, an I wasdting my time? It is ridiculously complicated

[@gotnoshoes99]

Am I the only one who didn't bother hooking up the PAS or brake levers?

[@Nickbaldeagle02]

I've got an E10 error. The bike works but the speed doesn't display.

[@tariqnaeem8575]

My s830 has an issues of company block all these setting i am not able to move any of those. I don't know it's the display meter fault or the company did it

[@sergioinsunza1325]

So I have the s830 display. So after I got done swapping my wheels my front to the back my back to the front. When I was done I flipped it around connected everything. Turned it on everything started to work except my MPH reading isn't working now everything else works but that . Would know how I can fix that

my 2000w hub motor, says i go over 50 kmph but i go walk speed. i have 29 inch, and in setup set it to 29" if i put it on 26" it still shows morekmph then i actaly go.. and sometimes it does not show speed at all, then it says 00 kmph. nc81f display , what can be the problem ?

on how much do i need to set the p7 ? for my 2000w hub rear motor ?

[@chickenmonster576]

Hi I know this is 2 years ago am having a promblem my battery percent always says 100 percent

[@user-wf2ek8hz8g]

Wait so does non zero start got to be on for pedal and throttle

i dont think so, but now i am not sure anymore after i seen this video, i think its p10 for both trottle and paddle assist. p9 i s just how it start up, 0 non start with trottle and 1 with trottle.

[@qaz9258]

Wonder if someone can help me understand what happened to my SW900 LCD display. It now shows what looks close to "bn3.6" when I first give the display power but is not on. Then When I turn it off via the M button it simply says "OFF" but does not turn off. I left it for 5+ minutes and it was still on displaying OFF. I have to now turn off the battery to get the LCD to turn off.

[@eproud55]

My SW900 doesn't have a setting P10. How can I access that setting, and a few other missing ones?

[@johnpaulpajaron7898]

How solve KT-LCD5 My problem Lcd display 555 No work motor because Lcd 555

[@thecollinzboy]

I have a gotrax ebe2 ebike that has a 350 watt motor on it. its factory default setting is set to P8-100. on 100 the bike only reaches top speed of 20mph. if i set p8 to 50 will the bike go faster than the 20mph cap? and maybe hit 28mph?

watch what your max ah current from controller can handle, put p14 on there, and but the right volt in what battery you have.

[@firelord4662]

You know anything about the trans pro scooter dual motor is anybody knowledgeable on it ?,😔

[@albertgutierrez7036]

Does this work for store bought ebikes I have a gotrax and I screwed up big time and need to reset the setting back to factory.

[@beatsbytani7875]

P18 is to factory reset

[@JmieYoutube]

Liked 👍🏻 and Subscribed, thanks for this info

[@sandrodegan9623]

Hi, I have an SW900 on my bike, it broke so I bought an S830 to replace it, but it doesn't work as expected. It turns off while pedaling. Unfortunately the SW900 does not show all the information, example P07 does not show! From P06 it goes straight to P08. Can you give a tip?

[@sandrodegan9623]

Battery: SDBS-S26J-20A 48V10.4AH/499.2Wh Controller for brushless motor LSW1295-9M X1710019022

[@chrissinclair8705]

For your "voltage collapse", which I'm assuming you mean low voltage cutoff, it should be at 40 volts not 48! 48v is the nominal voltage of the li-ion battery pack, made up of 3.7v cells in banks in series to get that 48v. If you look at a li-ion cell when fully charged they are at 4.2v after a little over half used they are 3.7. There is still half of the battery left until it gets to its discharged voltage of 2.8. Maybe if you wanted to preserve the battery or have a huge reserve or something to save %50+ of the battery capacity. Hey, if you want to do that more power to you....literally. But it's not getting to the wheel.

[@HONOROFCOURSE]

How to stop low voltage cutoff

[@chrissinclair8705]

@@HONOROFCOURSE Don't go that low. The low voltage cutoff is to protect the battery. It's always good to give yourself a little safety of error. Trust me once the voltage gets down to that level you'll be going 10mph..maybe. You'll want to charge the battery. It's regulated by the controller and BMS module. You don't want to damage the battery. You are doing just fine.

[@jonnose16]

​@@HONOROFCOURSE😊

[@dawidnowak2358]

On my screen show me always 100%battery do you know why? Pls help me

[@CarsandCoding]

Did you ever figure this out? My voltage goes down but the battery always shows 100% as well.

[@look-within]

@@CarsandCoding hi; I had the same problem and I’m going to take a guess as I’m on my 4th new battery now. Ok so what I believe is happening is your battery is coming to the end of its recharge life cycle, so when it gives you an 100% percentage is because your battery voltage is lagging on full charge so this creates a error in the battery reading; I know this for sure as it happened to me back in 2019 and this year 2022 just about 20 charge cycles before both my batteries died, so I’m just guessing the display shows an error on the battery percentage bar due to low voltage charge levels when battery is operating only at 80% efficiently so after full charge let’s say a 48 volt battery should be 54.60 fully if it’s charging to 100% efficiency but when only 80% due to end of life you get error reading on the bar, hope this helps

[@CarsandCoding]

@@look-within this makes sense as I’m my battery was bought used

[@singood7790]

My battery when fully charged will say 100% for several days but the power drains more and more each time I'm using it from like 92% down to 10%. Slowly goes down from 100 after I start hitting the 60% range while using the throttle. In other words it's designed to say 100 even if it's not technically.

[@eigengrau2819]

my s830 only has two ps

[@peterbateman8018]

So, if I want 5 PAS setting, I go into P05 and select 1 05 Is that correct?

[@hookedandcooked9434]

I just tried the 50k mode and my battery stopped working

[@zrinkobarnjak9952]

I have a eroor 07 Does anyone know what it is

[@smartel4949]

Comment faire pour que l'assitance 1, soit a 5km et non a 10km ?

[@flowinthrou]

I bought samebike lo26 500w and the max speed setting was already set to 100 but the max speed is 25km/h. Changing the value to anything does not change the max speed. Is it locked?

[@jonoomahony6278]

Must be ...i have the same bike it goes 35kmh on throttle alone...40+peddling..hold the left or brake and the throttle together for a few seconds

[@cadentaffe8495]

Can you set the speed for cruise control on the s830

[@AugustineEBikes]

No it's locked in at 6 mph

[@stevnalexan300]

Viewing another reply . If you hold the down button it sets the bike in walk assist mode. To set cruise mode. You throttle to desired speed and then hold the down button. I have not tested it yet.

[@tcgames9622]

Does this work with GOTRAX bikes?

[@qweasz562]

is it possible to set the walking mode for 15 - 13 km on the display s 830

[@AugustineEBikes]

It should already be set, just hold down the down arrow key for 4 to 5 seconds

[@qweasz562]

@@AugustineEBikes I can't SET the speed of 13-15 KM by myself ??

[@robotbroken]

I recently purchased a Voilamart 1500w 48v kit that includes the SW-900 LCD. It sits in a box until I can budget a battery pack and the remaining pieces that I need to convert one of my bicycles. Since my purchase, I've been led by many that have made the Voilamart conversion, to believe that the PAS on the kit does not work and only gives full throttle no matter how slow the cranks are turned. Since learning this I thought that I may have to rely on throttle only for more precise motor control, but now after watching this video, I wonder if some of these settings discussed might make the PAS usable on the Voilamart kits?

[@sovereignman6951]

My first Voilamart kit didn't have a display and it did want to go at full power, to be expected when the controller has no display to program it I guess. I would change the settings to the lowest and go from there. Most important ! cover the display if there's any chance you might get caught in rain. The black plastic case itself seems watertight but the perspex screen has no protection, I had an inch of water in there ( it still worked but a week later it died ).

[@robotbroken]

@@sovereignman6951 I will have to try the PAS when I go to install the kit and see what it does with the options on the display. Thanks for the tip on the display! I will try to keep it as dry as possible.

[@billfoster6809]

Just answering for future readers. PAS levels only set a speed (ie... PAS 1 may give 11mph, and PAS 2 gives 13mph...etc. ). It is not a TORQUE sensor which would give power to the motor based on the amount of power you are pedalling. So when you pedal in PAS 1 the controller tries to take you to 11mph regardless of how hard or easy you are pedalling. That's what PAS does.

[@smashaj2955]

How do you install it

[@jher6969]

Can I add 1 of these screens to my voilamart 1000w 48v kit? It only came wit a lid screen that shows how many bars are left on the battery.

[@boomhauer421]

I set P14 Max Peak Amp to 15 but when I ride up a steep hill with my display on Current, the Current goes up to 33! Is my S830 broken?

[@GurwinderSingh-ss5ym]

E 09 error??

[@massterrbarber]

I see this is like a three-year-old video if you got any updated stuff anything yeah I got a Jetson electric bike and I’m trying increase the range. I can’t afford a battery right now. Well, so I’m thinking about just lifting the 15 miles an hour, but just getting a new controller or something you know if I update controller to the same thing like a 36 V system you know what I’m saying just switch out the controllers. I’m just trying to go with this the right way because I can wait. I just feel restricted you know 15.5 miles an hour 48 years old, I can handle some speed at first I got this not knowing anything about electrical bikes if I did, I would’ve just I probably would’ve got the same type of bike. I just would not have gotten that low of a speed with 20 with 20. I’m good. I just don’t want to change the controller and then it lifts all of limits if that happens I won’t even write it until I get the right system to go with it so it don’t overheat or catch on fire. I’m very aware and I’m being very safe or I would’ve done the.shunt mod already but I didn’t because I don’t understand it. What I do understand is that it’s going to trick the controller so that means this going to be some overheating going on and I don’t even got no thermal paste put all over it and stuff like that to get it all ready and prepared for the heat. if you have any advice, can you please share?

[@AlexChristaki]

Will you just get on with it.... 2.50 is when is starts! 0 OMG, you've actually explained nothing!

[@massterrbarber]

I see this is like a three-year-old video if you got any updated stuff anything yeah I got a Jetson electric bike and I’m trying increase the range. I can’t afford a battery right now. Well, so I’m thinking about just lifting the 15 miles an hour, but just getting a new controller or something you know if I update controller to the same thing like a 36 V system you know what I’m saying just switch out the controllers. I’m just trying to go with this the right way because I can wait. I just feel restricted you know 15.5 miles an hour 48 years old, I can handle some speed at first I got this not knowing anything about electrical bikes if I did, I would’ve just I probably would’ve got the same type of bike. I just would not have gotten that low of a speed with 20 with 20. I’m good. I just don’t want to change the controller and then it lifts all of limits if that happens I won’t even write it until I get the right system to go with it so it don’t overheat or catch on fire. I’m very aware and I’m being very safe or I would’ve done the.shunt mod already but I didn’t because I don’t understand it. What I do understand is that it’s going to trick the controller so that means this going to be some overheating going on and I don’t even got no thermal paste put all over it and stuff like that to get it all ready and prepared for the heat. if you have any advice, can you please share?