Porsche Instrument Cluster - Tach Face Upgrade DIY

[@MarriedTooTheMiles]

Looks fantastic, the sticky notes idea was genius

[@AutoAmateur]

Haha. Thanks!

[@alberthilt]

Looks Fantastic! Just enough for the cluster... Steering wheel: YES. Seat Belts: YES That should make for a great interior!

[@AutoAmateur]

Thanks!! Appreciate the advice!

[@ian_b8477]

Just finished up my tach gauge face change. Your 2 vids on this topic are extremely helpful The tip for releasing the green cable connector on the previous vid really helped. I figured out that it didn't release from the front but couldn't see where the release was at the back. After seeing your previous vid ...BINGO :) - Also, glad you found my tip on holding the snap clips open useful. I discovered that method while dismantling the cluster on a previous car . - one other thing I found this time was removal of the left air vent was not necessary . A couple of trim tools released the plastic gauge surround trim quite easily. Keep up the great work!! Your vids are very much appreciated 👍

[@AutoAmateur]

Thank you and great job!!

[@Carbonfiberchris]

I like the idea of yellow seats belts but no yellow stiching on the steering wheel. It will be the only thing with colored stitching. It won’t match the rest of the car and the next thing you know you’re buying yellow stitching for everything. I would just add the yellow notch and yellow seat belts. And call it good. Just my two cents.

[@AutoAmateur]

You know of course I’ve already been searching for alllllllll the yellow stitched leather trim…. 🙄😂

[@OhYeahAboutThat]

Love it. Love the steering wheel and seatbelts, too.

[@AutoAmateur]

Cheers!!

[@MarriedTooTheMiles]

This is the one I needed to see, I’m going to tackle my swap during the holidays. Fingers crossed I’ve been putting it off for a year

[@AutoAmateur]

You can do it!! 🙌

[@slippy1404]

Looks fantastic, I’d do yellow belts too. I remember do this on my XR3i many years back 😬

[@WhiskeyWatchesandWheels]

James, great job as always.

[@AutoAmateur]

Thanks so much!!

[@DMR777-p5o]

Yellow looks great

[@AutoAmateur]

Cheers!

[@andrebrown8792]

Love the yellow. 💛

[@AutoAmateur]

Cheers mate!

[@bmwnthzst]

Nice touch on the center gauge in yellow. I would add all 4 belts in yellow however I would leave the steering wheel as is.

[@AutoAmateur]

Thanks!! General consensus seems to be a big yes for the yellow seat belts but people are divided about the wheel!!

[@kramer8865]

The yellow looks really good, agree with you only doing the tach, doing all of the dials would have been too much yellow. I like the idea of you doing the seatbelts and steering wheel as well, I bet it would compliment the interior nicely.

[@AutoAmateur]

Thanks 👍

[@andyp9040]

Whens your next video james? You used to release loads!

[@Pboy7272]

You should've used yellow post-its.

[@AutoAmateur]

Hahahaha. Fair.

[@f1dog]

Looking forward to your new videos. When are you going to add that performance chip to your car?

[@AutoAmateur]

Very soon!

[@sueddo2634]

Excellent video, just bought a set from gaugeface and planning to do this install soon. Did you disconnect the battery during the install? Concerned whether error lights would pop up if I disconnected the gauge with the battery plugged.

[@AutoAmateur]

Thanks! No, I didn't disconnect the battery before doing this job but you certainly can to be safe. I've done this job on a couple of different types of Porsche cars now and never had a problem. I only really disconnect the battery when I'm playing around with any trim that involves airbags or seatbelt sensors and then I wait a good 20 mins or so after disconnecting the battery before touching anything.

[@jonrichmond]

Does the swap from the white numbering to the black numbers on the yellow face make any difference at night?

[@AutoAmateur]

No! Visibility and usefulness is still the same.

[@_LeeTurner]

I notice the numbers where white on taco you pulled out but the new yellow numbers are black. Is there a reason you went this way when you can buy yellow tacos with white numbers to match??

[@AutoAmateur]

Great observation!! I wanted it to match my sports chrono which has blacking font on top of the yellow. I think the white font on the tach face would look really good too though.

[@_LeeTurner]

@@AutoAmateur only reason I raised it is I’m doing the same thing with my yellow 991 (with just the taco). The black numbers look better but I went with the white matching numbers. It arrives soon so we’ll see.

[@robinsongalaxie500]

Hi James. Did you do this on your 997 too? DIY similar to the 991?

[@AutoAmateur]

The DIY is basically the same the only difference is that it’s all or nothing with the 997. All of the faces are connected. I can produce them with the center face a different color with the rest black or white but they all get replaced in one go.

[@AutoAmateur]

Example: www.autoamateur.com/product-page/porsche-997-1-911-gt3-gt3-rs-9k-rpm-manual-225-mph-black

[@steveminor6300]

Love it! Still can't get myself to do this to my car yet....lol. I'm chicken!

[@AutoAmateur]

Admittedly, it's quite a daunting job! I can appreciate that.

[@steveminor6300]

Looks sick once done though! @@AutoAmateur

[@seandenny1553]

I think it looks good but I think it would look good with all of them being yellow and yellow seatbelts there’s a lot of black in there it’ll balance

[@AutoAmateur]

Thanks Sean! I might give the other faces / dials a try to see what I think. I can always swap them back if I think it's too much.

[@luisrolandorios]

Greetings If it wasn't you, you have a twin, I saw him in Puerto Rico...

[@AutoAmateur]

This week??? I was there!! Sunday to today, Thursday. Where?

[@luisrolandorios]

@@AutoAmateur I live in Puerto Rico and I have followed you for a long time since I have a Porsche

[@birrol]

Ouch