Automatic water level controller using arduino | Water tank level monitoring system with Ultrasonic

[@mohammadhanif875]

IT'S WORK 100% !!! Thankyou very much brother. May God always blessed you.

[@manojkumars2057]

Plz send me bro

[@mohammadhanif875]

@ send what?

[@manojkumars2057]

@mohammadhanif875 program

[@manojkumars2057]

@@mohammadhanif875 water level program bro

[@manojkumars2057]

@@mohammadhanif875 bro plz send the code as soon as possible

[@knowledge_seeker80]

after long research we have a new technology to send data over dc lines so no need to connect 4 wires of ultrasonic module just use same dc line between module and MCU to supply module & get data

[@1stltchannel890]

Bro this coding shows some errors

[@nilanjanmondal360]

Sir if I use it in bigger tank then what changes we have to do?

[@rajkunwar1454]

what is the maximum range of that an ultrasound sensor?

[@gushi221]

4.5 m aprox

[@tasniacordiva2373]

where u have connected the black covered wire(from 220V AC) ? what kind of adapter did u use?

[@Lava-i3g]

It wasn’t for the pump it was for powering the Arduino and circuit board

[@benoitracine1700]

Your file fore codes are full of virus, can youpost the code here?

[@adeelhyderkalhoro3419]

what is work of mini push button?

[@lusoclement3787]

i really wish you put at least subtitles in the video if your not gonna talk, I didn't understand what's happening especially around the time 10:08

[@cashrow_]

having error in uploading error statement = Sketch uses 4710 bytes (14%) of program storage space. Maximum is 32256 bytes. Global variables use 325 bytes (15%) of dynamic memory, leaving 1723 bytes for local variables. Maximum is 2048 bytes.

[@tamaragondwe8957]

were you able to fix it? if so, how?

[@momtazmole8698]

Please provide me the code for this project.

[@sairam-786]

I tried this project and added library module the Ultrasonic sensor is working fine but the 16×2 lcd display is not working its shows just green screen 😑.I bought the lcd and i2c module separate and I didn't do soldering screen because its risky if i do a single wrong step the whole machine is gone so only pls give suggestion whether i do it myself or get help from professional is it necessary to get the display of the screen or you can get the screen without soldering i tried putting the ic2 module in multiple ways but it didn't work pls reply 🙏

[@arpansrivastava6405]

just rotate the screw in the i2c module and see is the word visible or not.

[@sairam-786]

@@arpansrivastava6405 Thankfully now it visible after soldering but there is an error in code sometimes water level switches between 0 to 110 real quick I don't know how to fix this 😅

[@adeyemiwisdom1056]

​@@sairam-786 can u share the code pls I really need it

[@Nelosiren]

@@adeyemiwisdom1056 bro there is literally the code in description

[@Nandini_Veligandla-ku2zt]

Bro where did you connect the last water pipe

[@arnabmondal9009]

Inside tank water vapour is very high...can ultrasonic sensor work in high humidity condition?

[@diyprojects5767]

Use a waterproof ultrasonic sensor not the one showed on the video

[@josuke6131]

​@diyprojects5767 i have done this but the sensor isn't functioning. Is it because of the coding or something else? The sensor is newly bought JSN-SR04T

[@mitsolution1755]

Excellent work. Can you tell me where the nubber in the formula (110) came from????

[@094georgekuttymj8]

Wow....nice content

[@slideas1]

Thank u

[@mayankverma8318]

Sir can you please make one which makes use of 4 wires as sensors and the display shows percentage as 25% 50% 75% and 100% and rest auto and manual feature remains same... I would be really grateful if you could make that one because it is more convenient to install because ultrasonic sensor gets damaged by water vapours. Hoping for a quick response.

[@dhaghithakam5463]

what if i want to use mini LED? not the big lamp like that, can i? and i dont know what the 220v ac, what is that?

[@krissvlog1144]

Whete did you connect the 220 VC

[@electronicsideas1361]

no matching function for call to 'LiquidCrystal_I2C::begin()

[@UmmeeAwan]

Sir kindly provide the links of libraries

[@salmakhalid1333]

We can fit it in the 1000 litre tank or not

[@SunilSunil-iv3we]

Sir display not showing any text what i do any body help me

[@Vellz08]

sir why my lcd error when the relay got loads? but if i dont connect to load the system work well

[@subhamsrimaniee4207]

the same problem i am facing now. Did you find any solution?

[@naemytuutaleni658]

What if I want to have two pumps? What changes can I bring in?

[@taufik460]

what is the function of the EEPROM library.?

[@meujala]

What is the indicator when the lamp is on/off??

[@Hemanarayan1404]

Can you please provide proper circuit diagram

[@Hemanarayan1404]

Can u please reply Saturday is our project submission for that this is more required

[@boininanditha]

Can I use float sensor in place of ultrasonic sensor?

[@xavieralpha2174]

thank you for the video, just tell me why you didn't use the simple water and it's with the colored water that you used.

[@skd7626]

Does it have fluctuations

[@karthikonline4974]

Manuval setting in tank overfull relay cut off possible yes/No

[@JANARDANKASALE_]

I use led instead of pump and it worked and not worked with pump can you explain me please

[@prakashsharma789]

I connect the bulb to relay but is not working.any one suggest me what can i do for fix this problem?

[@Rahuls098]

What if we skip relay module?

[@fiyahhyde1690]

thanks so much, this is the video i was looking for to help with my gardening project. Will this sensor be able to hold up to small sprinkles of water, or do you think there is a better sensor that is more waterproof?

[@slideas1]

Thank u....

[@harshachannel4785]

​@@slideas1 sheesh hudidjz

[@dubmob151]

You can use stainless steel wire probes as ground contact sensors, I used three wires, set with ground, low level, and high level. When the wire contacts the water the Arduino input voltage will drop, and that detection can be used to turn the pump on and off.

[@1stltchannel890]

I have display only how to use it

[@05eceamaldeep95]

Bro how to place a switch to confirm to fill the tank when the display indicates water level is low... plz reply bro

[@hendritresnahadi4146]

How can i void ultrasonic modul from splasing water? Tx u

[@omorfaruk1]

I have made one, but when water reaches at half position or lower than it can not identify the level, why?

[@dhruvsaxena8286]

I think you need to adjust the distance in the code according to your tank size.

[@rjgalambao4239]

is this working on an actual solar pump?

[@shalinisingh3855]

I don't have that black colour cable which is connected to arduino so what should i do...please help i have to show it tomorrow in my college

[@slideas1]

Which black cable ? Vedio time

[@shalinisingh3855]

9.46

[@slideas1]

@@shalinisingh3855 dc power supply ....12v 2A .....

[@frangalic7306]

hi can you please tell me which pump did you use fror this

[@babupillai3992]

Sir programs file download nhi ho rha hai. Help kijiye download karne me. Plz reply me

[@susilnishantha5111]

Doesn't verify your code ..???

[@atherawan1898]

can i base this PID based project?????????

[@rustyaji]

can use jsn sr04t ?

[@shafiqmisnawi5637]

Hello sir can i get the real coding because the water pump and ultrasonic sensor not responding

[@shrutibarve4922]

yes pls... i am also facing the same problem

[@momtazmole8698]

Did you get the code?

[@rafiqnadaf1801]

How can i make motor start when water level is high (when water container is full)

[@chanakyasinha8046]

Manual switch override

[@rajeevkk901]

Hai bro can u make a video for water low level and high level announcement only ( no motor operation) using Arduino uno and TF card mini mp3 module plz? 3 wire float switch for low level and high level to be used.

[@mimoshossain3371]

how could i get complete circuit?

[@shrutibarve4922]

hello sir...pls help...my lcd display and sensor is not working ....lcd only showing green colour

[@slideas1]

Re try and watch lcd display Vedios

[@Vishwas-w3l]

Bro what is the connections of tank

[@sandhyar8694]

Sir plz can u say which software is used for simulation circuit and its code

[@techchick5770]

Fritzing

[@adadmohamedcherif192]

Thanks for this project, but there is a real problem with the HC. SR04 designed like this. How to protect it from humidity coming from water in the long run?

[@slideas1]

Thankfully, this is a very important issue. Alternatively, only the transmitter and receiver of the ultrasonic sensor (SR04) should be left open and the rest of the circuit should be sealed with water vapor (with a suitable glue or insulating fluid). Experience has shown that this can be used for a longer period of time.

[@adadmohamedcherif192]

@@slideas1 Thanks , What worries me are the transmitter and receiver of the SR04. I'll take your advice into consideration. Greetings from Algeria

[@pookoye]

use JSN-SR04 which is waterproof & costs below 500 Rs.

[@Akkisworlds]

@@adadmohamedcherif192 Use JNS HC04T Waterproof Ultrasonic Sensor this Sensor is better than HC04

[@muhammadiqbalanjum9621]

plz use a spray one or two cote aerosol paint Lacquer

[@boopeshkumarprabhakaran]

Please add dry run protection and would this work for 2 capacitor submersible moter pump?

[@kpinnovations6613]

kzbin.info/www/bejne/gpLKZoqhmbCrZ68 See this video u r problem will be solved

[@advanceideamechanic8880]

I have a system usning SRO4 sensor for sabmersible and 1 hp moter if you need plse contact me

[@Anumarajuganesh-eb2vh]

sir i buy these project can you sell to me

[@firewater365]

New to microcontrollers. Is there a way I could do the reverse and add water to the tank once it hit a low level?

[@xavieralpha2174]

yes

[@iamirsaline2376]

@@xavieralpha2174 how?

[@xavieralpha2174]

@@iamirsaline2376 cool, and you

[@yudinpalma939]

CAN WE BARROW YOUR DIAGRAM TO USE IT TO OUR PROJECT IN CAPSTONE? ☺

[@slideas1]

Ok

[@techyh3216]

Pls pls explain source code one time

[@sphelelethwala6130]

Can this be powered by 12v battery?

[@slideas1]

Yes 👍

[@abhaychoudhary4445]

which software is this?

[@sivaanisriprabakar6382]

how can we connect program

[@jeremiahokonkwo5649]

Hello brother, thank you so much for the video it has been helpful for my school project but I am having issues with the LCD display screen nothing seems to be showing but other components are working

[@denkunweselamalah875]

Check the lcd address

[@josuke6131]

Rotate the screw on the i2c module

[@karansaini5385]

hllo my project in running condition but the after some time the jumper wire goes melt

[@manavsingh6708]

Bro can you send me how you made this project

[@sriganeshreddy-s7e]

Bro this code is not working Showing an error

[@newtamilchannel3337]

Can you pls support to share the code for OLED display with 4 pins

[@omkar_patil_3642]

Sir please send me the code of project The link is not working.

[@s.s.gaming7388]

Bro i am getting lcd.begin eerot

[@s.s.gaming7388]

Bro I am getting lcd begging error

[@dinithiperera8282]

LCD display eka on wenawa but monawath display wenne nane...? ai e kyl kynna puluwnda...?

[@slideas1]

Mulinma lcd display thiyana wena program code akak download karala (mage channel eke thiyana (How to make clock wage) balanna hariyanawada kiyala eta passe me code eka upload karanna...

[@slideas1]

Ehema wenna hethu kipayakma wnna puluwan.....

[@aydeesam1768]

Thanks for the informative video, but can you add 2.4ghz wireless modules for transmission of ultrasonic sensor data? It will make the system wireless and those modules are also very cheap, i jave overhead tank at 3rd floor so i will jave ro use a long wire but if you use wireless modules it will solve that problem. Waiting for your reply.

[@slideas1]

Thank you so much for your response. You are right.

[@aydeesam1768]

@@slideas1 so I'm waiting for your next video with these changes. Thanks

[@slideas1]

@@aydeesam1768 👍

[@sriganeshreddy-s7e]

HLO BRO HELP ME CODE IS NOT WORKING THERE IS AN ERROR

[@1stltchannel890]

Bro I don't have display circuit

[@chandresh.v5830]

What volt is relay module

[@slideas1]

5v

[@chandresh.v5830]

Thanks

[@hanajk231]

How can I get code for this?

[@slideas1]

Code in description ....download

[@adeismail2340]

How the water is clear water? This device still work?

[@slideas1]

Yes work

[@arbindkumar6000]

Lcd is not showing anything, I also tried screwing it but the letter are not showing.......help!!! @sl ideas

[@shrutibarve4922]

yes pls .......i am also facing same problem

[@aakashthakre244]

I have installed lcd i2 library still facing error no matching function And when i comment lcd.begin() It works but doesn't upload shows sar can't open device

[@aakashthakre244]

Please help me fast anyone

[@nazeelnazir]

use lcd.init()

[@mitsolution1755]

JUst write in between the two ptracets the LCD type. i.e >>>>> lcd.begin(16, 2); it will work 100%

[@ashutosh7675]

use lcd begin(16,2)

[@poppurumadhu782]

hlo sir plz link provide for ppt for the project

[@jananrao3705]

Showing no matching function liquid crystal begin()

[@thomasjinu6923]

Hi dear appreciate your effort. I have a question that. When the unit power up ,relay on and off , two or three times faster ,then it's steady working ok. If possible please solve it in the programme , add delay programme for relay powerup .

[@slideas1]

Thank you so much for your comments

[@nazeelnazir]

change the relay pin. Don't use pin 13 for relays because it has an LED indicator. It always blinks a few times when the Arduino powers up.

[@අඛිලමෙන්ඩිස්]

ගොඩක් වටින වීඩියෝවක්.. ඉස්සර නම් ඉලෙක්ට්‍රොනික විද්‍යාව සම්බන්ධයෙන් පොත්පත් තිබුනා. ඒ අඩුව පුරවන්න මේ වගේ අනර්ඝ වීඩියෝ දකින්න ලැබීම ඉතා වටිනවා..

[@slideas1]

ගොඩක් ස්තුති සහොදරයා..තමාගේ වටිනා කාලය වැය කොට ලබාදුන් අදහසට ගොඩක් ස්තුති.

[@sujithsubramanian5357]

Hi Bro the program code is not matching On lcd. begin () ; The error is no matching function for call to Liquid crystal I2C

[@sujithsubramanian5357]

Can you provide the link of library for this operation

[@slideas1]

@@sujithsubramanian5357 library include ...download ..

[@madugangamarasingha4534]

sir Where can I get this programe code?

[@atiqurrahman5206]

Can i get this complete device from you?

[@EbenezerSam-c5m]

Please can you help me My project is vehicle fuel theft monitoring and calling system These are the component I have used Arduino uno GSM sim800l Ultrasonic sensor Working principle If the flow of the fuel in the tank increases than the normal flow rate

[@christianpatrice4048]

Can the 220V AC connection be connected a normal plug on a wall? Also how can you put a buzzer on this?

[@rjgalambao4239]

(2)

[@advanceideamechanic8880]

Hi sir if you need he proper working system plse contact me

[@kurtlawrence3864]

someone help me how to fix LiquidCrystal_I2C.h: no such file or directory...I already download the Library

[@sooraj3128]

Got to lcd libraries link in the description box. Download the zip file. Right click on the downloaded file, click extract all and paste it on, documents>arduino>libraries. That's it...

[@parthasarathikk-iy8eu]

how to download the code

[@Ana_Wa_Ant]

Unfortunately, the background music is very annoying and does not help focus😔

[@abdurriassufi5752]

Izin tanya bang punya saya sudah bener upload codinganya tapi kok sensornya ngga mau gerak ya ?;

[@yinhe9914]

Ask you guys, and the host: Are the codes in the links FREE? What is the cost for the hardware system? Thanks.

[@Drift_wheeler]

What is this 12c module . Where to buy it . I have only 16*2 LCD display. Are there any other names for this device?

[@slideas1]

The i2c module can easily activate the lcd display

[@nareshjain5339]

Dear friend, thanks for beautiful project, let me know can I change ultrasonic sensor with water proof ultrasonic sensor, if yes then please tell me changes in circuit or code

[@hrivudasmunshi656]

My project is not working actually display issue

[@Ajay-t3u]

I know how to rectify

[@chanakyasinha8046]

How?

[@Ajay-t3u]

@@chanakyasinha8046 Which display u are using I2C display

[@chanakyasinha8046]

@@Ajay-t3u oled display with I2C/IIC serial interface

[@rahulpethare1810]

My screen is showing blank only. after uploading program!. please help me where I am doing mistake!

[@jananrao3705]

Bro while uploading code it's showing error about i2c

[@Ajay-t3u]

I know how to rectify

[@hazir23]

​@@Ajay-t3uhelp

[@karthikonline4974]

750liter set val details

[@Agam_22verma]

I need circuit diagram

[@englishtopsongs8012]

අයියේ ගෙදර වතුර ටැංකියට මේක හදද්දි කෝඩ් එකේ වෙනස් කරන්න දේවල් තියේද

[@slideas1]

ටැංකිය උස අනුව පොඩි වෙනස්කම් කිහිපයක් කලයුතුය්

[@englishtopsongs8012]

@@slideas1 ඒ ටික කියන්න පුලුවන්ද අයියේ

[@shakarappa914]

Code error