MUST WATCH IF YOU ARE DOING TIMING CHAIN OR BELT REPLACEMENT ON MAZDA FORD

[@AutoRepairGuys]

⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzbin.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

[@NullH3ad]

I just did a front timing cover reseal on a 14 Focus .. I learned this lesson the hard way. I ended up with p0016 timing correlation code, but surprisingly the engine did run. Your video helped me to understand that the crank sprocket is not keyed to the crank, nor is the pulley which contains the crankshaft position sensor reluctor wheel. I was able to lock the crank in place and roll the cams back into alignement and all is well. Thanks for this video, it was very helpful.

[@alexhoexum9548]

Thanks for the video, great info here and this is the same motor that’s in my Ranger so this video helped a ton!

[@Shirkatron]

just did a timing cover re-seal and learned this lesson the hard way.

[@cjslowman08]

Did you use old crank bolt?

[@Shirkatron]

@@cjslowman08 Yup I’ve been working for Subaru for seven years as a SM Tech now I do used cars for extra coin. The job looked very similar to our chain cover re-seals and other Toyota chain cover re-seals so I did not focus on reading every warning on Shop Key Pro. Before removing the crank I saw the reluctor gear and said “weird”, double checked Shop Key and said “well I don’t have the special tool”....”I’ll just mark the pulley against the timing cover”. Three hrs later car won’t start. Then print out all the data from Shop Key, including the safety info and supplemental info. A pot of coffee later I call my Ford guy (who’s a foreman now) and say “how bad can someone shot their self in the foot doing a timing cover re-seal without knowing the warnings?”. His response was “you pulled the crank pulley without the stay tools...ugh...we’re getting an average of one a week this year. The whole engine is out of time and the valves are probably bent”.

[@Shirkatron]

@@cjslowman08 yes I reused the crank bolt and diamond lock washer.

[@cjslowman08]

@@Shirkatron I did a front timing cover reseal on a 2015 ford escape 2.5 for the first time. l reused the crank bolt and diamond coated washer. Did a test drive and everything is fine. I just heard it is recommended that a new crank bolt was nessasary when taking off crank bolt. I had co workers that helped me that have done this. Didn't read Mitchel even though I printed up the instructions.

[@Shirkatron]

@@cjslowman08 i mainly work on Subaru and you would be surprised at the bolts, washers, and seals they want replaced when taking a timing cover off. Like your coworkers I used good judgement and decide on what needs to be replaced. If the crank bolt didn’t fight me coming out, I keep it. If I didn’t rip the crank seal taking the cover off, I keep it.

[@ephraimcamacho9600]

Thanks for the info!!!

[@videogregor]

Very informative video. Thx!

[@carlosbanegas7577]

thank very moch very good video

[@grippingyarnsuk]

Great video. Can you do that on an mx 5 nc with the engine in ?

[@pocketaas75]

Does this apply to both the Mazda 5 2.3 and 2.5 liter engines?

[@nelsonmartinez1281]

If they come with timing chain yes it’s apply for them!

[@joeshafer881]

So what millage interval would you recommend to change timming chain on this 2.5 I can't find a maintenance interval for this job... they say the chain is good for life of vehicle but I don't buy thay

[@mashrurahmedkaify9305]

Hi, i have an 2009 ford fusion se 2.3l automatic. My question is can I put a standard transmission from mazda3? If so, do I need to use the ecu from the mazda3 aswell?

[@ignatiusabrahamshapaka2071]

I replaced the timing belt on a 1800 Mazda F8 engine. The timing marks on the cam pulley is A or B or CX. Which of these are the correct setting? Much appreciate your help in this.

[@carlosbanegas7577]

thank you very moch

[@gilgodinez1018]

Thus happened to me, crank pulley jumped. Heads have to be worked on now. Now my question is, if pistons look ok, did this hurt the crankshaft or piston bearings? Pistons are able to smoothly go up and down. I removed the oil pan, no debris in there.

[@dirtrider5001]

how did it happen, was it torqued correctly?

[@gilgodinez1018]

@@dirtrider5001 got the car this way. Took heads to a machine shop, installed them back in. Car seems fine now. Two valves were replaced by shop.

[@vinceking719]

Thanks for the info but ypu could have explained that in 30 seconds. i came here to learn how to set the new timing chain.

[@ryanramlochan1504]

Do you have a diagram for a mazda e5 timing marks,it's a carburetor engine

[@erasmosolis1963]

Does Mazda 1992, B2600i have the belt that doesn't have the small canal ?

[@iCrazyBoy99]

Thank you so much for the explanation, you got a new subscriber

[@nikeshnabee]

When will the f30 timing chain video be available to watch

[@govinseelochan4925]

I look everywhere and cant find the engine number in the Mazda 5 engine,,,help

[@יהושעלוי-מ5ט]

hello dear how I install vvt gear Ford mondeo

[@gertis7420]

Great info. Does this motor have friction washers on the crankshaft?

[@chriscusick6890]

Yes it does

[@govinseelochan4925]

Where is the engine number in the mazda 5 engine,,,,from Sanjay from trinidad

[@abisismael1343]

Thanks

[@zacosa4569]

Ok well...how about setting the timing properly then where is that?

[@davidsimmons5936]

I'm Jesus I'm in gold Beach Oregon hi friend

[@WaveAction777]

Why is that pulley not keyed?

[@tyronenur2373]

I guess friction washers are cheaper or easier to manufacture 😂

[@Billo-07]

@@tyronenur2373 And then they require special tools and take twice as long to install and time, so i imagine they save a few cents a motor and cause headaches for everyone.

[@juanmanuelocampo2397]

Does the friction washers need be clean to do his function?

[@GUIRADE95]

What's the torque specs on that crankshaft bolt tks.

[@knocksensor3203]

Or get yourself a 90s Toyota 😗👌

[@kwalatamonate3713]

Mazda LF 20 timing

[@pandanda656]

you sound bulgarian dude

[@rodrawlings2204]

Welp this engine just went bye bye!!!

[@armunro]

I just keep hearing bad things about Ford. The not fit for purpose dual clutch autos, the eco boost engines that wear out quickly, etc.

[@wendellgreenidge3362]

Why do I keep getting unsubbed from your channel???

[@marcomolina6493]

Sounds like ford did it on purpose

[@butterflydoze]

Bye bye lol

[@NoName-ux3by]

i don't understand SHITTTT

[@kickbackentertainment4466]

Get off KZbin this is smut there’s no knowledge here just rambling

[@teresanelli6281]

Thanks