Holley TPS Kit Episode 444 Autorestomod

[@TheJoefussGarage]

Wow, there was a hater on two on this one.. I did enjoy it though... Love that wagon... The 4r70W seems to do quite nicely... If I can bring myself to spend the money, I want this trans, and 347 as well.. I think 🤔 after 3 years, this segment is wearing well boys...

[@edp9811]

So is this all i would need to run an engine with a carburetor in my tbi truck with a 4l60e transmission? Removing the old tbi engine to swap in a stronger carb engine but want to keep my electric controlled transmission

[@JoJo-x9z]

So i would need this and nothing else for it to work with my 4l80 ? I have ez tcu computer for the transmission

[@AutoRestoMod]

Probably.

[@matiashernandez5584]

Donde lo puedo conseguir

[@AutoRestoMod]

Summit Racing.

[@ericdolan2130]

Another great video, guys. The clearance problem is just SOP! Nothing in this hobby is ever perfect. Hell, most of the Factory stuff isn't any better. I'd love to do this on the '69 F250 360 / C6, but the Boy wants to keep her as stock as possible. So I'll have to just watch and drool.... Maybe I should just find me a '74 Torino Wagon like my first car. 351C w / C6....Yeah, that's it! Swap the trans, rear, and suspension out of my '08 Crown Vic...You guys are a bad influence! I have enough of these tendencies without your help. Keep up the good work!

[@AutoRestoMod]

Hahahahaha. DO IT...DO IT NOW.

[@jamescarver5497]

I'm installing this for my vortec swap, the issue i have is knowing how to set the tps properly for my stock engine to my 4l60e. I haven't a clue nor the electronics needed to get the right voltage or onow when to set the shift points..any suggestions..the only electronic thing i have is an ammeter.?

[@chickenfoundation9323]

Just wish it wasn’t $170 , can get a tps sensor plus pigtail for $40 but now need to find out how to get the rest lol

[@AutoRestoMod]

That pay to play part hurts for sure. I get the cost on the controller, too, but shelling out the coin makes me go ouch.

[@billyparker8903]

Had the very same problems plus one. Extension that inserts inside the sensor wasn't sticking out far enough to actually mate with the sensor itself. Had to modify the mounting bracket to get what it should be to properly work.

[@AutoRestoMod]

Glad you figured it out.

[@dewaynedavis177]

Will it work the same on a 1997 s10 t

[@AutoRestoMod]

As long as the S10 has that type of carburetor on it that TPS will work

[@highrzr]

You have to be careful with line pressure on the 4r70's & 4R75's. Cranking it up will get you firmer shifts. If it's too high, you'll burn the trans up.

[@AutoRestoMod]

Thanks!

[@danielmcqueen1024]

The real amazing thing I saw... Cam got a hare cut :)

[@AutoRestoMod]

Lol.

[@1966human]

Throttle body fuel injection is looking pretty good

[@AutoRestoMod]

Hahahahaha. Cost per pound is pretty high though. We may get into a fuel injection system just to see what we get.

[@williamgrant5783]

Good job

[@CarminesRCTipsandTricks]

TPS on a HOLLEY!!! 😲😲😲😎 OK, you've probably seen a few, but I never imagined it was possible!!! I'm guessing that if I ran an Edelbrock Carb, they have a Kit for it? I'm really getting excited now! Except.... I would need Cameron to come over and do the Programming. I've had NO practical experience in Computer Tuning. You're also warming me to the idea of maybe getting a WAGON!! 😳 Face it, in 1981, you wouldn't be caught DEAD showing up at School in a Mama Wagon. BUT, now that we're in our later 50's........ The practicality can't be denied - with enough POWER!! 😁 You're giving me ideas DAMNIT! If I can finally get enough to get a Car again, I was really set on a Foxbody Mustang. But then, Wagons probably haven't been BEATEN within an inch of their Lives.... So that's something to ponder. They're generally cheaper than Coupes, right? 😧 Carmine ✈🚂🚙

[@AutoRestoMod]

Yes, there is a TPS for the Elebrock. I perfer Holley only because I have run them since 1981.

[@CarminesRCTipsandTricks]

@@AutoRestoMod That's funny. I run Edelbrock, because I've run HOLLEYS since 1980!!! (Power Valves!!!😖😖😠) Although I've been told that Holley FINALLY fixed those damn things - that would blow if you even SNEEZED near one!! 😜 The V4 PVs are supposed to finally be blowout proof, but I haven't had any experience with them. Since around 1988, I've always ran Edelbrocks, Autolite 4100s, Carter AFBs, and I've even figured out over many years how to make a Quadrapuke actually Work well - and give surprising Highway Mileage!! 😉

[@kurtyb9682]

Would does work for 454 with 4l80e transmission

[@AutoRestoMod]

I think the one for the 4L is different. There are a few available I'd try and get one that is compatible with the controller you are using (if it is aftermarket, for instance get the US sift TPS if you re using a US shift controller).

[@reeferaddickt66]

Great video series, I'm in the process of adding a 347 + 4r70w and the quick4 to a 64 econoline. Any tips on troubleshooting the Holly TPS sensor showing 0.0 voltage? I had it working but now someone adjusted the electric choke and it seems to have stopped picking up the voltage. I measured and I'm getting 5.1v on the grey cable going to the 3 wire TPS plug/connector. Thank you very much for these videos and your time.

[@AutoRestoMod]

Make sure the choke is not set, try a recalibration. Also check that there is some preload on the spring. I'd also remove the TPS and have a look at the plastic blades to make sure they aren't damaged.

[@reeferaddickt66]

@@AutoRestoMod Thank you very much for the help, I'm going to check these possible issues.

[@stephenhotzjustdriveit]

Thx for the tps install.

[@kgooch69]

I love grocery getters...I've been trying to get a 61 falcon 2 door wagon away from my neighbor for a while now....I think one will be my next project after I'm done with my crown vic swapped 62 f-100.

[@johnpena9165]

Just curious why do you need a TPS on a carburetor, is it for a nitrous oxide system ?

[@AutoRestoMod]

the 4R70W uses a TPS to control the shifts on the transmission.

[@dragonslair59]

Great episode. Love long roofs and more doors. Hard to haul friends and family with 2 doors, unless they are people ya don't like and stuff them in back seat of a 2dr. But then ya want a pinto or chevette to put them in the back seat. Lol

[@paulreis553]

Do you have the part number for the TPS bracket

[@AutoRestoMod]

Holley Throttle Position Sensor with Electric Choke: 534-202

[@mechanicwarrior20]

How do you adjust the fast idle screw if the TPS is in the way?

[@jjmccloud]

Do you think using the an braided dual feed lines it would clear the tps shaft since the hose will be a bit flexible

[@AutoRestoMod]

Yes. but I don't like the look. Silly, I know.

[@biglakehotrods381]

Because wagons are bitchin!!! Keep it in stupid mode, it’s a hot rod!

[@GTguitarworks]

Any way you could re-due this, All I could see is your hands, Sorry

[@Paulie1232]

Send me your address, I'm going to send you a new backdrop...

[@AutoRestoMod]

I like my backdrop...its called "the wall." 😁

[@Paulie1232]

@@AutoRestoMod I'll send you a new one...lol

[@brendentaylor8976]

@@AutoRestoMod i bought the tps kit swaped out my tbi for a holley double pump 650 and it feels like I only have 2 and 3rd

[@Thirdgen83]

What's the point of a throttle position sensor on a Holley carb?

[@christopherhudson7465]

If u run a 4l60e or 80e

[@brendentaylor8976]

@@christopherhudson7465 how i tried and I lost gears i think 1st and overdrive tell me something please

[@bigjoe599]

How do you adjust the tps switch if it is shifting to slow or to fast?

[@AutoRestoMod]

That is more a function of the transmission controller in the 4R70W.