I just fixed mine. My local hardware store was out of the repair kit. So I placed a thin piece of plastic I cut from a child's applesauce container. I inserted the plastic behind the washer to push it out a hair. Now it works perfectly. Give it a try...
@Yophillips32723 жыл бұрын
Jerry rigging I like the way you think 👍 going to try that now.
@jindo3333333 жыл бұрын
Thank you but you should show us how to replace the diverter. That's the most important thing to know. Because I tried but I couldn't
@dennisyounker2422 Жыл бұрын
Thanks! I bought the kit at Home Depot (about $8), removed the old diverter, cleaned it up and cleaned up the inside of the spout, then put in the new washer and put the diverter back in. Works perfectly now! Thank you, thank you! (I couldn't get the spout off the pipe so did it upside down like in the video. Easy to do.)
@Jillz14u3 жыл бұрын
This video showed me which way the washer needs to sit inside the slide and I needed that info! Thanks!!
@st8kout961 Жыл бұрын
At 2:25 it's easy to free the white plastic from the pull rod. Just find a thick screw with a pointed end, insert it between the pull rod and the spout (the end closest to you) so it will expand the white tabs, and just turn the screw by hand while pulling up on the pull rod; comes right out without damaging the white plastic.
@ronrealtor8883 жыл бұрын
Thank for taking your time to help others. Even though we did not get to see how to remove the diverter, it is not a hard process. I did find out that you can actually buy the inexpensive part to replace instead of buying a complete new faucet as everyone else is saying what to do. Thanks again you saved me time and money.
@Xstevenn3 жыл бұрын
Looks like a bad calcium build up too. A good way is to soak that whole spout into hot water and vinegar and use a tooth brush to scrub it off
@Myself-yh9rr7 ай бұрын
My spout leaks too. It gets nice thin streams that would leave those spots noticeably cleaner if my shower was neglected enough.
@cookmaster3626 Жыл бұрын
The toughest part is removing the rod from the plastic sliding piece. I tried to remove one from a diverter out of the tub and it is tough and most likely you can damage the plastic part in doing so. One of these days i am planning to make me a plastic sliding part with a 3D printer that will have threaded hole and i will male my own rod that will have a threaded end to fit on the plastic slide so all i will need is a new washer when it goes bad.
@weeratne Жыл бұрын
Question. What if the diverter pulled half way up gives a better shower pressure with water leaking from the spout vs very LOW pressure from the shower pulled ALL the way with no water leaking from the spout?
@brian21002 жыл бұрын
Good trick any advice dealing with soft poop stoppages
@recessiontwentytwenty38585 жыл бұрын
Showed the problem ,solution but not the actual repair
@Utube67622 ай бұрын
Would've helped if you'd actually shown HOW you got the white diverter and washer out of the spout.
@bmarshall26544 жыл бұрын
Why didn’t you show how to pull out the part that needs replacement? That was the most important thing to know
@sumgue49643 жыл бұрын
Because it's nearly impossible unless you have >2 arms. Took me 15 minutes of fanagling with pliers to get it off.. He mentions in the video he cannot do it while holding the phone.
@Argyle3023 жыл бұрын
Yes, he conveniently skipped that part, didn’t he.
@jnrflores143 жыл бұрын
if you use a kitchen fork its really easy
@charleshodgdon61682 жыл бұрын
If everything else is basically in good condition, you can unscrew the knob piece on the top. The rest of the diverter should then slide out of the spout.
@cookmaster3626 Жыл бұрын
@@charleshodgdon6168 The knob piece at the top is NOT screwed to the shaft. It is either brazed or a press fitted or a single machined part. They made it so you will not be able to easily unscrew remove the knob and fix it easily by changing the rubber washer or seal. These designers are crooks and want to make it UNREPAIRABLE so they can sell the whole unit. American Corporate GREED they are good at.
@sandymilne2243 жыл бұрын
You are showing that the washer is in the wrong way. Flat side goes to mate with the clean-up surface.
@whiskeygrunt7726 жыл бұрын
You just need to unscrew the thumb pull from the top of the diverter. Everything else will then come out.
@dstapleton795 жыл бұрын
Does the water pressure from the shower head increase when you fix it?
@jojoloren3 жыл бұрын
@Whiskeygrunt Thank you, will try it!
@josephechanes4962 жыл бұрын
how about moen and kohler tub spout, are they the same repair kit? im using kohler brand but i cant find repair kit only moen is available that seems to me they have simillar repair kit $6 home depot👍🏼. kohler tub spout range to $50-$80 so sad😔
@karenstapleton8370 Жыл бұрын
Did you get an answer? Does Moen fit Kohler? Thanks
@Sal1123502 жыл бұрын
You should show how you remove and replace with the kit, eventhough you fix it already.
@simplelifewithlyn2 жыл бұрын
thanks for this, new subscriber here.
@BPoweredLove4 жыл бұрын
Didn't show how to remove spout. Didn't show how to clean up mineral deposits. Didn't show replacing the mechanism.
@googleuno21892 жыл бұрын
Thank you so much
@munirshaikh35012 жыл бұрын
I broke the plastic by spiliting it.I could not find the same plastic piece with washer.changed complete spout bought from Reno depot.
@Sunshroom__5 жыл бұрын
Next time title this video: Waste Your Time
@jacksonvang2946 Жыл бұрын
What if I change my and still doing the same thing?
@giyoon2152 жыл бұрын
Flat part of the cup washer is facing out (as shown on vid)
@happynurse87063 жыл бұрын
All you showed me was there were parts to buy not how to remove or replace
@Mandy_392 жыл бұрын
Wish you would've shown fixing it..
@gregdasso2274 жыл бұрын
Thank you for the video!
@CreamyBone2 жыл бұрын
💗💗💗
@robprinz98845 жыл бұрын
Dude, you didn't show the actual repair. F;n joke
@ExpertaGroup2 жыл бұрын
very nice ! ;)
@bladesofgrassjramseykcaste78723 жыл бұрын
You did not show how to install the new one! That’s what I was looking for.
@J03LBM3 жыл бұрын
He said how to do it and helped me ? Just listen?
@theteleisewilliamsexperience3 жыл бұрын
@@J03LBM No he didn't I'm doing this and figure out how 2 get the plunger in the tabs
@charleshodgdon61682 жыл бұрын
Unscrew the knob of the diverter and the rest should slide out the bottom of the spout. Replace the rubber piece, shove the diverter up from the bottom, and then replace the knob. If you already removed the piece from the tabs, use pliers to push the pieces back together. If your spout is covered in junk like this one, you should remove the spout and clean it. All those mineral deposits can cause a groove in the diverter. Take the spout off. Remove the rubber piece from the diverter and the one just under the knob. Place the spout, diverter, and other pieces in a container of vinegar. Do not put the rubber pieces in their as vinegar can slowly eat away at rubber. Then take everything out of the vinegar, scrub it clean, and rinse it off. Put everything back together. There are many videos on the whole process. Some do not mention removing the rubber pieces, but this is important to do.
@beckyfred59492 жыл бұрын
@@charleshodgdon6168 my diverter knob does not unscrew, and yes I’ve tried pliers. Do I just break the white plastic part and hope the new one fits? Whoever installed our fixtures did a bang up job so installing a whole new diverter is out of the question without pulling down a wood wall.
@sassynfree8842 жыл бұрын
This video is great, EXCEPT that you showed the problem, and the solution, but never showed the real "HOW TO". I'm getting closer, but what I NEED is how to take that stuff apart. You didn't show that🤷🏼♀️
@DnyAln5 жыл бұрын
No help at all
@franksolar4503 жыл бұрын
still leaking some water from faucet...what up?
@1575murray2 жыл бұрын
This happened to me after I replaced the washer. I wound up replacing the whole spout because the inside was corroded and did not allow the washer to seal properly.
@KDWinTexas5 жыл бұрын
What is up with this guy? He showed one tub and faucet at the 0:15 mark, and another one at the end. In the first one, no caulk around the spout, the rack hanging from the shower head is empty, and the bottles are in the left corner. At the end, the spout has caulk sealing the fit against the tile, the rack is full of stuff, and the bottles are in the right corner. Bizarre.
@Hungrytube24 жыл бұрын
Lol I noticed that to
@sombongi4 жыл бұрын
Lol, at first I thought someone is off his meds again, then I realized it was sarcasm.
@cydneewilliams2193 жыл бұрын
He clearly told us he already fixed that one and is going to do the other one in the other washroom 🤷🏾♀️🙄
@randalceniceros81572 жыл бұрын
Lame. You didn’t show how to change
@abdonrodriguez35864 жыл бұрын
learned nothing..
@flaviomoreno16403 жыл бұрын
You didn’t show anything!
@SK-qn1fw3 жыл бұрын
it's so easy once he shows you, just take a flat head screw driver separate the plastic part out without breaking it, and up pulls the little thumb handle. Please, people, don't complain about the lack of actual repair. It's so intuitive once he tells you the problem, just put on your thinking cap. Don't expect to be spoon fed.
@charleshodgdon61682 жыл бұрын
This is not a very good video. He doesn't mention cleaning the spout properly, didn't mention that you can unscrew the knob and the rest of the diverter slips out the spout, and no other basic information.
@MinhTran-fc7jl Жыл бұрын
lousy instruction
@OSediqi4 жыл бұрын
This video explains the process better: kzbin.info/www/bejne/oJrJfnmqn76CmpY