Behringer XENYX X1832USB Mixer

Behringer XENYX X1832USB Mixer Demo
Song played in this video:
Retro Synths - SKYNET: • Retro Synths - SKYNET

[@HENJAM48]

If in doubt read the manual. - Back in the day, I would put a deposit on a piece of gear and then take the Manual Home. I would read the Manual 3 or 4 times, and then pay the balance and take the item home. Trust me... it Works, and in this age of downloadable manuals, there really is no excuse. I did find this video useful, but honestly I knew more about the mixer before watching it, than you did, making it.

[@djdenentertainment]

@ElliotJMusic in simple terms Sub is an output routing that has many uses. like recording a group (selected inputs) or can be used to link another mixer. For eg look at level control at ch 1. See a button labeled 1-2 or sub on this mixer if u press it. sound on ch 1 will be routed to sub than u can control it to another output.

[@TheYangwee]

nice review, i got to see most of the things i was looking for, but to give you some clearity and suggestions. sub stands for subgroup, in bigger mixers you can adjust more what's ruted to which output. this for it to be easier on stage or in practise to make the best sound to the different musicians, in terms of what they whant to hear to do their best. but of course awesome for other stuff as well if that need split signal with independent volume. mon out stands for mono output, often used for the sub so you independently can adjust the bass. i also recommend you to plug your mic through channel 1-6 where you have a pre-amp so you can get more control of the sound with less stress for the mixer, and you will free up a nice stereo input. the signal from the mic is a mono signal so it doesn't really matter.

[@PerfectKlaus]

Great review, thanks! I hadn't noticed that the stereo inputs didn't have a gain control...thanks for the tip!

[@shelleyellen9035]

Thank you so much.. I needede to figure our the effects and your direction was great.. My manuel is in every language except english so wonderfully and clear .. yes it took me a while but I got it . too bad you can't separate the channels.. again Mikey ,thanks.. rock on

[@RetroSynths]

Make sure the orange effects slider is all the way down and or the orange effects knobs are all the way to the left. You may be routing the MIC thru the delay effect. The RCA inputs bypass the effects and subwoofer bus. I wouldn't run the DVD player into the RCA inputs. You can buy RCA to 1/4 jacks for less than $1 on eBay or $5 at Radio Shack. Run the DVD player into one of the stereo channels.. Good Luck

[@mik300z]

Excellent demo, thankyou very much. I have the older version and this was very helpful to me, it really does have some excellent extra features. Behringer really make quality but affordable:)

[@adamskibreeze]

thanks alot for uploading, just got this mixer, its fantastic!

[@metallurjix]

Nice one Mikey, very informative and clear. Good job!

[@RetroSynths]

@mehdieminem - Most Pro Tools hardware interfaces accept balanced or unbalanced 1/4’’ inputs. All outputs on this mixer a fully balanced. I run the control room left and right channel outputs to my hardware interface and the main outs to my monitors.

[@praisedj]

which is connected to the microphone where you talking about? because the canon as empty,

[@WBCStudio.]

Thank you for the review. I am leaning toward buying, but is it good for a home recording studio?

[@theaman32197]

Is there any way to connect it to a DAW (Specifically Ableton) to either have all your sounds come through the mixer and get modified there, then returned to your DAW so you can record and export it and such?

[@maxottaway5616]

if you do not want to do it througe i would sujest the inserts in the back out to your computor tower sorry about my spelling btw

[@dewoputradi2017]

@@maxottaway5616 can you tell me the function of INSERTS. I Have this type of Mixer but i never use the inserts. No explanation in the manuals

[@ramoniak6]

@@dewoputradi2017 Insert (effects processing) In audio processing and sound reinforcement, an insert is an access point built into the mixing console, allowing the audio engineer to add external line level devices into the signal flow between the microphone preamplifier and the mix bus. (Source: Wikipedia)

[@BrunermanVideo]

Will this mixer work with GarageBand or Logic Pro 9? Will it work to adjust levels and individual effects on either or each program via the USB output?

[@jackelston2665]

What cable do you use to play your music through channel 7/8? Many thanks

[@AndMoe]

I'm looking at getting one for trance production and was wondering what your honest opinion would be.. I'm midi syncing hardware synths and drum machine and was wondering if this was a good idea as a starter mixer in order to produce this way?

[@Lorijenken]

can this apply to the older behringer xenyx 1832fx mixer ? NOT USB, the one I have is older version.

[@RetroSynths]

@mehdieminem - Yes, all the mono line ins have adjustable compression. The stereo inputs do not.

[@melodiumstudio6591]

Hi.. Can you help me how to reduce fx in monitor?? There is no dedicated knob for that..

[@RetroSynths]

Yes, all the XLR ports have phantom power. Their is a switch on the back to enable phantom power.

[@mariodelbeke285]

how many stereo inputs are there on the table... has it usb so i can program ableton live on it i need 4 stereo channels) + the possibility to adjust one knob of them to one function of ableton and another button to another function ) sorry for my poor englisch i never learned it in school ! it looks super but i need the ableton functions.

[@Ghost_Swe]

Nice reveiw, thank you

[@RetroSynths]

Although I am talking through the mixer on a mic, the audio is being picked up from my studio monitors and the onboard microphone on my video cam. This video was for an eBay sell and not done for professional intent.

[@Hansier62]

Helpfull review, pitty that you didn't read the manual. The mixer has many powerfull options that are unmentioned now. It's a low cost mixer with a compressor and low-cut on all mic-channels and a lot of effects and software. I'd want to know if all these options are working well and if the software is of any quallity: some reviews elswere say that the software is shit and cheap. However, good review but incomplete to use it as a guide for purchase.

[@IanCanefire]

Well done...great video... that echo was great on 8 and 9.

[@stevegreen7520]

Do you suggest that the low cut be engaged while doing voice for microphones? We are doing a podcast soon and trying to optimize sound quality.

[@Sk8MakeVideo]

+Steve Green yeah do that

[@jvonemolap0921]

hi, great review/tutorial. i just recently bought a second hand and it works great. the only thing im worried about is that after 2 hours of using it, underneath where the power supply is heating up a bit. is this normal and safe? also, i noticed that all the videos of the mixer here in youtube, the led power light and the fx number are in blue, mine is orange.

[@pbf98]

behringers site does have it. 64-bit USB ASIO driver is what you are looking for it is a USB Audio Driver.

[@flexo692]

Hi guys.I have an Xenyx1832FX which seems to have a problem.I gave it to my 6yr old daughter to plug and play guitar. Simple set up, plug in guitar and listen through headphones. The effects does not work. I bought a new board but this doesn't work either. LED comes on and you can change parameters but no effect on sound. Any ideas ???

[@maxottaway5616]

make sure the solo buton is not on and try to control the fx switch on the chanlle

[@jhunnjhunntv.8978]

I've bought this kind of mixer but in the first day of using I've encountered a lot of problem. main mix and sub button was easily broken. I can't assured if the item I've bought was genuine.

[@andypompura6139]

how do you set up a usb mixer to record separate tracks on pro tools?

[@jfdebaron]

Very good video... thanks...

[@peteryousef5177]

hello, please i have question. if i connect Trs to 1/4" Male TRS to 1/4" Female TS Insert Direct-Out Adapter ? can change insert to work a direct our ? or sec ,way if i connect TRS male to adapter Ts female to trs male. can change the insert to work a direct out ? i have 16 channel behringer

[@RetroSynths]

The mixer has mono balanced inputs and outputs and will accept TS or TRS cables. For optimal sound quality you can use TRS cables. If you adapt/connect a TS cable to a TRS cable you no longer have a balanced connection but the audio will still work just fine. Unless you have really long cable runs or interfering you are unlikely to hear a difference in sound quality between TS or TRS. I often use RCA cables with a TS adapter, it’s ghetto but works just fine with line level devices (keyboards or electronic instruments). TRS cables can be used for a single stereo channel but the mixer has left and right balanced channels for stereo. In other words you can use TS or TRS and will have a stereo output regardless. TRS just offers the best sound quality. Keep in mind whatever your connecting to the other end of the cable must also support balanced inputs or outputs otherwise your just wasting money on TRS cables.

[@peteryousef5177]

@@RetroSynths thank you ?

[@gavingavin4572]

Bruh every time I record with a mic or a guitar, I can hear the voice straight from the mixer and when I create a channel on Logic Pro x, I can hear both voices at the same time. I can’t get rid of it. I can hear both sounds at the same time. Help me

[@vjcoyote]

Im intresting about Pitch effect. I didnt hear enough, is there background delay? Or its pure pitched voice?

[@ronf57]

my big question is the usb to computer is it only stereo or more channel to DAW and can it take more channel back into it fro computer/DAW? good video thx

[@DummyShots23]

Thaks bro for this vid👍

[@MrSoylaostia]

4. Similar to question 3 .... I have several recorded tracks .. I have an acapella in a chorus in another and another one instrumental ... ¿I can control each track ... the same time? .. ie .. with buttons to control a track and another track buttons controls other 5.The top, entries that puts white and red (2 - TRACK / OUTPUT USB IMPUTED) to serve?

[@drinu93]

@jeremihc unfortuantly you can't do that.. i guess your using the usb interface right? the usb only sends out the main mix, no separate tracks. i have a question for you. on the Behringer XENXYX X1222usb is there 1/4" jack outputs, similar the the XLR stereo outputs on the top right corner?

[@codrutpetrut]

Hi I have a question I have a mixer like your speakers are put directly into the mixer ?

[@Freezerohmatic]

@mikeyhaas Sub stand for Sub channel, its use when you want to have 2 groups controled, ie vocals and instraments, the button that controled the main and the subs is used when you dont what to have that fine control over the 2 groups. but i do have a quick question for the channel eq, there is ment to be 4 controls do you know what bands they cover?

[@JSprayaEntertainment]

hey can line inputs be stereo ? i need to know if the aux send channels send in stereo or mono , so would i need 2 aux sends for a stereo reverb ?

[@MrSoylaostia]

I am Spanish and I have this mixing board ... but I have some doubts, because I can not spend as hardly or for serving. I would answer some questions. 1. If you have Windows 7 (OS) and the table is not going? 2. This table works with Adobe Audition 3.0? 3. With this table I can control the micro, ie record a cappella, and equalized by the board?

[@Falconurbex]

How do u connect a cd player to this mixer and a seperate amp as im going to start djaying im old scool so ile be using mini disk player and cd olay can u explain how i would connect both players to this and then how i connect a seperate amp thank you and i look foward to your reply many thanks

[@RetroSynths]

The cheap and easy method is to purchase RCA Female to 1/4 inch TS Male Adapters. You will need 6 of these adapters if you’re running a minidisc play, cd player, and feeding into and amp, assuming your using a stereo receiver as your amp. Otherwise you would use a two standard 1/4 inch audio cable for pro audio amps. You plug the adapters onto the end of your RCA patch cord and use the line input on channel 7/8 for minidisc and 9/10 for CD player. Just use the main outs to feed into your amp. You can use RCA cables with the 1/4 adapter.

[@jhook338hook9]

Excellent....thanks

[@tylerfyer]

i have this mixer, my fx has problems on orange slider do u need main down costo be up for input to work via pc, it recogonises all 6 mono channels but makes into 1 on pc

[@RetroSynths]

@mehdieminem Yes, the mbox 2 supports both balanced and unbalanced 1/4'' line inputs.

[@joshbale4466]

Thanks helped a lot

[@rebeccastratton7992]

does it work with the focusrite scarlett studio????

[@meggasoundinternational5562]

what is the difference between this one vs XENYX X2222USB ????????

[@dutimko]

HI ... it is possible to set up the FX processor similar to the effect of "old radio" or "megaphone? ... thanx

[@rspteam12]

do u know if u have it hooked to usb how many tracks could u record simultaneously

[@omarbento]

Boa noite! Comprei uma mesa de som Behringer 1622 usb 12 canais com efeitos. Liguei a mesa tudo certinho. O violão vai para a caixa e o microfone também. Só que quando aciono os efeitos nada acontece. O que estou fazendo de errado ou não estou fazendo? Algo falta conectar ou preciso de outro equipamento, tipo caixa amplificadora? agradeço Omar Bento

[@ryancayetano]

the mic is patch at the last channel of the mixer 13/14 sub channel, i think he's not using an XLR cable for the mic input, he's using just a TRS jack... nice video.. also planning to buy that mixer.. if it's not sold out.. :D

[@masoodjamily]

Thank you for the video it's been really informative my question is is this a powered mixer

[@lucasjessop621]

how do I record to my computer via the USB?

[@VietFlavorcoffee]

I just bought this mixer, but i dont know does it work for unpower speakers?

[@SlickCupid]

HI... im new to this and was wondering if this mixer would be good for recording.. will i be able to assign each input to a seperate track. (record a drum kit with 5 mics, and edit each mic after i have recorded it) Please let me know :) CHEERS

[@n70amu]

hi brother m new in sound stuff and all. i want to record my guitar solo. do u think for recording purpose i need mixer or a audio interface? like m audio first track pro??

[@pprriimmoopro]

hey guys can you tell me what is the difference Behringer Xenyx X2222USB and Behringer XENYX X1832USB Mixer ? And Behringer Xenyx X2222USB effects only do one at a time?? please tell me im a newbie..

[@SoundArtEnt]

Can You Use for recording and mixing in cubase all channels on diffident channels

[@TheMaceo900]

Good review thanks

[@NateMchaggis]

@mikeyhaas but you can use it to record to pro tools right?

[@AaronApocolypse1]

I don't think I saw an answer for this but can you run this into a software and record each track separately?

[@utubehound69]

No it's a stereo 2 trx or 2 mono trx. this is w/all the Beringer USB mixers. If yer doing studio work I'd go with the UMCHD 192K

[@andriealinsangao613]

@@utubehound69 So it's not a multi-track mixer?

[@utubehound69]

Yes you can run that way & also go into a DAW for recording that mix.@@andriealinsangao613

[@andriealinsangao613]

@@utubehound69 I'm sorry, what's that mean?

[@utubehound69]

You can use it as a stand alone mixer for a PA setup or sub mix say a drum kit to go into another interface or use the USB cable output to a PC / Mac to record the tracks to your PC but it won't control the faders in the DAW hope that helps.@@andriealinsangao613

[@Ruben837]

Hello, in the moneyandcool whats the name of the song of the video??

[@xyzclub3413]

how many speakers can you connect?

[@stonervill420]

does anyone know if these behringer mixers have phanton power for the main mix or individual buttons or for each input r something

[@redbook5544332211]

does this work with linux as the operating system on your computer

[@cletoalmonte9559]

Técnica loro-wasp400. De cuantos GB puede leer una memoria usb?

[@JSprayaEntertainment]

lol mikey nice vid but that sub part made me laugh good man , the mono out is for ya subwoofer and the subs1-2 could be used for suming & sending to PC leaving control outs for room moniters , cheers mate

[@babachalu1616]

Is this mixer good for active speakers

[@icetheboss9]

what mic do you use your studio sound so good to my ears

[@Trailmixorz]

Is this good to record drums and a guitar with?

[@a-donutcat]

can i use taht for professional music studio?

[@Skullclone]

Can you use this with a DAW software? Like Pro Tools, Mixcraft, audacity, etc.)

[@rolandgerard6064]

Good review, thanks

[@a-donutcat]

can i use this mixer for a pro studio music

[@LegetAdi]

The sound sounds really cool. I recently bought this mixer. I only have one question, what speakers does he use on this video?

[@rayonwilliamssportsandfun2106]

U try the monitor boxes ?

[@RetroSynths]

The mixer sold about two weeks after the video was posted. I just left the video up due to popular demand. moneyandcool

[@JGrandeUK1]

How isit picking up your voice without a Mic in?

[@jrmjazz]

correction : pro tools 9 you can use this mix or warever you want

[@mehdieminem]

im new to this. i have mbox 2 can i hook this up to mbox 2 and use it with protools?

[@LaharandMichelle]

LOL!! i laughed so hard when you said "aw i did it again damn it" in that effect!! hahaha! but i i liked the review thanks! :)

[@Hansier62]

There are two major differences between some models of this type: the Behringer Xenyx X12.., X16.., X18.. and X22.. have NO direct outputs, the X24.. has 8 direct outputs.

[@EmPtYcLiPz925]

can you use this mixer to control pro tools?

[@metalherrera]

Nice Review!!!

[@John48778]

what fx number suitable for live vocal?

[@maxottaway5616]

1 or 2

[@RetroSynths]

Good question. Although it comes with a USB cable and its own recording software I don't believe you can control ProTools with it. I am pretty sure only ProTools certified hardware will mixer control.

[@Ruben837]

Hello! Whats the song of 10:38? Thank you!! I’ve been trying to find it for years but its impossible

[@RetroSynths]

@@Ruben837 I made that song using a Korg M3 and likely a Nord Lead 2x. I still might have it on file somewhere and will see if I can find it.

[@RetroSynths]

Here is a link to the song: kzbin.info/www/bejne/rqjNqmumrpKeq6s

[@desert2012warrior]

I’ll take that mixer.

[@mehdieminem]

can you compress with this mixer?

[@mrbluetoothward]

This will work with Ableton Live, which is awesome and perfect if you just want to get to recording. there is a 30 day free trial too.

[@lucasjessop621]

how do you get it to record on Ableton? I've tried everything...

[@anthonyeward]

Hit me on email and I'll walk you through my setup and see what you are missing. I use it with Ableton Live 10 on Mac and I works great. [e-mail]

[@Irish614]

No phantom power? that is usually pretty standard nowadays. I was looking into this for recording drums but not without Phantom power.

[@kiatsumi7355]

Um, I know 8 years etc etc, but for interested ones, there is phantom power

[@BryanBlaz]

Can this be use with adobe audition 3???

[@fifielcoolio]

yo man if i had say 6 mics to record drums could i record each mic on its own seperate channel on the EnergyXT2.5 software with only the usb.. and then each track be on its own track on the screen, like not all being recorded as 1 track.. thanks

[@anthonyeward]

You can use just one mic and record each one on it own track. Why would you need 6 mics? You would need 6 sound booths too.

[@drumgod0695]

What kind of speakers does it take?

[@anthonyeward]

Any speakers, but designed for studio monitors, I think. It has RCA and XLR inputs.

[@TheMcBravo]

buen vídeo!

[@solohelltown]

@mikeyhaas Can u control fl studio with it

[@wayjo07]

can it connect on my mac using usb?

[@ramiromaldonadojr]

how many watts does it have

[@dewoputradi2017]

does anyone can show me the function of INSERT?